IMPORTANT SAFETY INSTRUCTIONS This symbol is to alert you to important operating or servicing instructions that may appear in the user's manual. Always follow basic safety precautions when using this product to reduce the risk of injury, fire, or electrical shock. When using this product, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1.
FCC REGULATIONS Modifying or tampering with the telephone's internal components can cause a malfunction and might invalidate the tele- phone's warranty and void your FCC authorization to operate it. If the trouble is harming the telephone lines, the telephone company might ask you to disconnect the telephone until you have resolved the problem. As it complies with Part 68 of the FCC rules, your unit has been registered with the FCC.
BATTERY CAUTIONARY INSTRUCTIONS BATTERIES: CAUTION To Reduce the risk of fire or injury to persons, read and follow these instructions: • For the cordless handset, use only 3.6V 600mAh Nickel Cadmium (Ni-Cd), RDAA600 cordless telephone replace- ment battery packs. (Included). •...
IBM-3415 PARTS CHECKLIST IN USE VOLUME PQRS WXYZ OPER TONE REDIAL FLASH CHARGE/ IN USE 1. Handset 2. Base 3. Reversible pedestal 5. Belt-Clip 6. Ni-Cd Battery Pack 4. DC power adapter QUICK START GUIDE IBM-3415 IBM-3150 ® SETTING UP THE BASE...
LOCATION OF CONTROLS AND FEATURES Handset View Antenna Headset Jack Volume Up/Down Keys IN USE In Use LED Talk Key Channel Key VOLUME Dial Pad PQRS WXYZ OPER TONE Temporary Tone Key Memory Key Redial Key Flash Key REDIAL FLASH Ringer ON/OFF Switch Microphone...
Page 8
LOCATION OF CONTROLS AND FEATURES Talk P The TALK key is used to access the telephone line. Dial Pad Numeric keys are used in the conventional manner for dialing. Flash Key G The G key is used to access telephone company services, like call waiting. Redial Key F The telephone will automatically redial the last number dialed.
LOCATION OF CONTROLS AND FEATURES Base View Antenna Handset Catch Page Button Charging Contacts Charge/In Use LED CHARGE/ IN USE PAGE - Used to initiate a handset page Handset Catch - Used to hold handset on the base when wall mounted Charging Contacts - Used to recharge battery in handset and reset the security code Charge/In Use LED - On when the handset is charging, or when the phone is in use...
LOCATION OF CONTROLS AND FEATURES Right Side View Data Jack Data Jack Used for connecting to a computer or fax machine. Rear View Use only with class 2 Power Source 300mA DC-9V TEL LINE Tone Pulse DC-9V Telephone Switch Jack Line Jack Tone/Pulse Switch Used to set the dialing method for tone or pulse dialing.
CHOOSING A LOCATION Do the following: • Choose the best location • Connect the base phone • Choose the dialing mode Away from VCR’s, TV sets and other electronic equipment Away from noise sources such as a Away from heat sources, such as radiators, air ducts, and sunlight window by a street with heavy traffic Away from a...
TELEPHONE SETUP Connecting the Phone to the Wall Jack BASE Use only with class 2 Power Source 300mA DC-9V TEL LINE PEDESTAL Note: This unit can be desk or wall mounted. 1. Insert the pedestal into the slots on the bottom of the base and slide up to lock in place. The pedestal is reversible for desk or wall mounting.
TELEPHONE SETUP Wall Mounting The IBM-3415 telephone may be installed on the studs of a standard wall phone plate or onto two screws (not included) fastened into the wall. When installing screws into plasterboard walls, use wall anchors (not included) to insure that the screws remain secure. Insert the screws into the wall leaving 3/16"...
TELEPHONE SETUP Tone/Pulse Switch 1. Choose the correct dialing mode Use only with class 2 Power Source 300mA 2. Select either Tone or Pulse dialing mode by setting the switch at the back of the base unit. Note: Changes to the switch position during a call do not take effect until the call has ended. Tip: If you are unsure of the proper dialing mode, make a trial call with the dial mode setting to TONE.
BATTERY INSTALLATION Battery Installation To install the 3.6V 600mAh cordless handset battery pack: 1. Slide open the battery compartment door on the back of the handset. 2. Insert the battery pack so that its connectors line up with those built into the handset. 3.
HEADSET AND DATA JACK The Data Jack The jack located on the side of the telephone labeled "DATA " is a convenience jack. It is useful for connecting a fax machine or modem when there is no telephone jack available for that device.
FLASH Flash handset back in the base. Redialing 1. Press P, once the IBM-3415 has acquired a line, press F to redial the number last dialed. To Receive a Call Waiting Call Press G to go to the new caller •...
SPEED DIALING The IBM-3415 will store up to 10 speed dial numbers. Storing Phone Numbers 1. With the handset in the idle state, press E. The handset will beep. 2. Dial the number you wish to store up to 16 digits and press E.
OTHER FEATURES Using the Handset Finder (PAGE) 1. Press N on the base, and if the handset is within range, the handset will beep for 20 seconds. 2. Press any key on the handset to stop the page find feature. Out-of-Range Warning If you venture too far from the base, the handset will beep a warning tone.
1. Keep the IBM-3415 away from heat as high temperatures can shorten the life of the electrical components and distort or melt its plastic parts. 2. The IBM-3415 should be kept free of dust and moisture. If it gets wet, wipe it dry immediately. Liquids can contain minerals that can corrode electronic circuits.
TROUBLESHOOTING No dial tone/phone will not dial out. • Check that you have plugged the AC power adapter into a working AC power outlet. • Confirm that the AC power adapter is plugged into the DC jack on the base of the unit. •...
From 91 days to 365 days, you may return the IBM-3415 to TT Systems LLC at the following address: TT Systems LLC, 4 Executive Plaza, Yonkers, New York 10701. Shipping charges are at the customer’s expense. Please include a copy of your sales receipt and a check or money order made out to TT Systems LLC for the amount of $14.50 to cover shipping and handling.