Honeywell genesis 7580g Quick Start Manual

Honeywell genesis 7580g Quick Start Manual

Presentation area imager
Hide thumbs Also See for genesis 7580g:


Genesis 7580g
Presentation Area Imager

Quick Start Guide

Aller à
Gehe zu
日本語 :
如要到中国简体) 。
pour le français.
로 이동합니다 .
für Deutsch.
7580-QS Rev B


Table of Contents

Summary of Contents for Honeywell genesis 7580g

  • Page 1: Quick Start Guide

    Genesis 7580g Presentation Area Imager Quick Start Guide Aller à pour le français. Gehe zu für Deutsch. 日本語 : をご覧ください。 如要到中国简体) 。 查看繁体版请登陆 한글 로 이동합니다 . 7580-QS Rev B 8/13...
  • Page 2: Getting Started

    Note: Refer to your user’s guide for information about cleaning your device. For localized language versions of this document, go to Getting Started Turn off computer’s power before connecting the scanner, then power up the computer once the scanner is fully connected. Power Supply Assembly (if included) Note: The power supply must be ordered separately, if needed.
  • Page 3: Connecting The Scanner

    Connecting the Scanner USB: Keyboard Wedge: Note: For Keyboard Wedge, only use the power supply if required.
  • Page 4 RS232 Serial Port: RS485:...
  • Page 5 USB: RS232:...
  • Page 6: Reading Techniques

    Reading Techniques Present the bar code to the scanner. The aimer turns on and the LEDs turn up to read the code. If the light level in the room is not high enough, the code may not be read. Standard Product Defaults The following bar code resets all standard product default settings.
  • Page 7: Usb Pc Keyboard

    USB PC Keyboard USB Serial If you are using a Microsoft® Windows® PC, you must down- load a driver from the Honeywell website ( The driver will use the next avail- able COM Port number. Scan the following code to program the scanner to emulate a regular RS232-based COM Port.
  • Page 8: Keyboard Country

    Keyboard Country Scan the Program Keyboard Country bar code below, then scan the numeric bar code(s) from page 13, then the Save bar code to program the keyboard for your country. As a general rule, the following characters are not supported by the scanner for countries other than the United States: @ | $ # { } [ ] = / ‘...
  • Page 9: Scan Modes

    Scan Modes When in Presentation mode, the scanner is activated when it “sees” a bar code. When in Streaming Presentation mode, the scanner leaves the scan illumination on all the time and continuously searches for bar codes. When in Presentation - Mobile Phone mode, your scanner is optimized to read bar codes from mobile phone or other LED displays.
  • Page 10: Add Code Id Prefix To All Symbologies

    Suffix If you want a carriage return after the bar code, scan the Add CR Suffix bar code. To add a tab after the bar code, scan the Add Tab Suffix bar code. Otherwise, scan the Remove Suffix bar code to remove the suffixes.
  • Page 11: Function Code Transmit

    Function Code Transmit When this selection is enabled and function codes are contained within the scanned data, the scanner transmits the function code to the terminal. Charts of these function codes are provided in your User’s Guide. When the scanner is in keyboard wedge mode, the scan code is converted to a key code before it is transmitted.
  • Page 12: Data Format Editor Instructions

    Data Format Editor Instructions The following are abbreviated instructions for entering a data format. For complete instructions refer to your User’s Guide, available at our website, 1. Scan the Enter Data Format symbol. 2. Primary/Alternate Format: scan 0 for Primary Format 3.
  • Page 13: Programming Chart

    Programming Chart...
  • Page 14 Save...
  • Page 15: Technical Assistance

    For localized versions of this document, and to download the User’s Guide, go to Disclaimer Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made.
  • Page 16 Web Address:

Table of Contents