Table of Contents
Advertisement
Quick Links
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
These instructions are supplementary to the Installation and
Operating Instructions supplied with the fi replace and should be
kept together. Refer to the Installation and Operating Instructions
for proper gas supply, safety requirements and operating
instructions
281009-12
TC42
CHALET
BURNER KIT
INSTRUCTIONS
PART#
TC42.NG01.C
For TC 42
Series C
TC42.NG01.C
5056.426.C1
Advertisement
Table of Contents
Related Manuals for T&C TC42
Summary of Contents for T&C TC42
- Page 1 These instructions are supplementary to the Installation and Operating Instructions supplied with the fi replace and should be kept together. Refer to the Installation and Operating Instructions for proper gas supply, safety requirements and operating instructions TC42 CHALET BURNER KIT INSTRUCTIONS PART# TC42.NG01.C...
-
Page 2: Contents Of Package
Contents of Package • BURNER ASSEMBLY • LOG GRATE • TC42 LOGS • EMBER MATERIAL • HARDWARE PACKAGE TC42.NG01.C 281009-12... - Page 3 4. Attach spark electrode (ORANGE) and sensor leads to the electrical bulk head. (Fig. # 4) (The spark electrode connection has a red dot above it) A panel set must now be installed. See Installation and Operating Instructions manual for details. TC42.NG01.C 281009-12...
-
Page 4: Ember Material Placement
Note: Ember material placement and amount will affect fl ame appearance. More ember material results in lower fl ame height. Add or remove as needed until desired fl ame affect. Fig. #6 LOG GRATE GLOWING EMBERS TC42.NG01.C 281009-12... -
Page 5: Log Placement
Step 5 Bottom Left Log Placement Step 6 Center Log Placement Note: Improper placement of logs will cause sooting on internal parts and glass. The logs may need to be repositioned slightly to avoid excessive fl ame impingement. TC42.NG01.C 281009-12... -
Page 6: Propane Conversion
(3/32”)(our part # 5021.31) manufacturer's instructions (Fig. #15) supplied with the kit. Fully open the primary air shutter. Reinstall the manifold and air defl ector. CAUTION The gas supply and electrical power shall be shut off before proceeding with the conversion. TC42.NG01.C 281009-12... - Page 7 (Fig. #19) Minimum rate screw Minimum rate screw Replace the minimum rate screw with the one provided in the propane conversion kit supplied with this fi replace. Ensure that the screw is fully installed. (Fig. #20) TC42.NG01.C 281009-12...
- Page 8 The access panel including the fi rebox with the previously removed screws. (Fig. #24) gasket must be reinstalled after conversion/ installation or servicing has been completed. Failure to do so will overheat and cause premature failure of the control system. TC42.NG01.C 281009-12...
-
Page 9: Gas Pressure Check
Correct gas pressure requirement: Supply Pressure Natural Gas Propane (For purpose of input adjustment) Minimum 5.0" WC 12.5" WC Maximum 13.9" WC 13.9" WC Manifold Pressure Maximum 3.8" WC 11.0" WC Minimum 2.1" WC 5.5" WC TC42.NG01.C 281009-12... -
Page 10: Burner Flame Adjustment
Operating Instructions manual. 2. Carefully remove the log set and set aside. 3. Loosen the screw in the Primary Air Shutter. 4. Rotate the shutter to increase or decrease the amount of primary air. 5. Reassemble as needed TC42.NG01.C 281009-12... -
Page 11: Kit Contents
#5..MAIN SUPPLY TUBE ......5019.223 #2..6 PCS LOG SET ......... 5098.31061 #6..PILOT TUBE ........5019.225 #3..ORIFICE, NATURAL GAS (#25) ..5022.12 #7..PROPANE CONVERSION KIT ... TC42.LPCE01 NOT SHOWN KIT CONTENTS: LOG #1 #1..BURNER ASSEMBLY #2.. - Page 12 TECHNICAL SUPPORT: 1-888-715-2664 www.townandcountryfi replaces.net 2975 Allenby Rd., Duncan, BC V9L 6V8 Printed in Canada...