Table of Contents
Advertisement
Quick Links
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
These instructions are supplementary to the Installation and
Operating Instructions supplied with the fireplace and should be
kept together. Refer to the Installation and Operating Instructions
for proper gas supply, safety requirements and operating
instructions
290409-12
TC36
HEARTWOOD
BURNER INSTALLATION
INSTRUCTIONS
PART#
TC36.NG05.C
FOR TC36 & TC36 AR
Series C
TC36.NG05.C
5056.427.C45
Advertisement
Table of Contents
Related Manuals for T&C TC36.NG05.C
Summary of Contents for T&C TC36.NG05.C
- Page 1 Operating Instructions supplied with the fireplace and should be kept together. Refer to the Installation and Operating Instructions for proper gas supply, safety requirements and operating instructions TC36 HEARTWOOD BURNER INSTALLATION INSTRUCTIONS PART# TC36.NG05.C FOR TC36 & TC36 AR Series C 290409-12 TC36.NG05.C 5056.427.C45...
-
Page 2: Contents Of Package
Contents of Package • BURNER ASSEMBLY (including pilot and manifold) • LOG GRATE • TC36 HEARTWOOD LOGS • EMBER MATERIAL • HARDWARE PACKAGE • AIR DEFLECTOR • COAL CHUNKS • VERMICULITE TC36.NG05.C 290409-12... -
Page 3: Burner Installation
Conceal the spark and sen- sor wires below the supply tubes. A panel set must now be installed. See Installation and Operating Instructions manual for details. 4. Position the slots of the grate securing Fig. # 4 brackets over the holes in the floor shield and secure with the two screws. (Fig. # 4) TC36.NG05.C 290409-12... - Page 4 Fig. #5 More ember material results in lower flame height. Add or remove as needed until desired flame affect. Reduce the amount used on Propane models, as too much will create soot Embers only in this area. Fig. #6 Embers, coal chunks and lava rock. TC36.NG05.C 290409-12...
-
Page 5: Log Placement
LEFT FRONT LOG, #3 Fig. #10 Fig. #12 Fig. #11 LOG WITH HOLE, #4 RIGHT CENTER LOG, #5 FRONT RIGHT LOG, #6 Fig. #13 Fig. #15 Fig. #14 RIGHT BASE LOG, #7 CENTER TWIG, #8 CENTER BASE CHUNK, #9 TC36.NG05.C 290409-12... -
Page 6: Propane Conversion
(Fig. #18) manufacturer's instructions supplied with the kit. 5. Fully open the primary air shutter. Reinstall the manifold assembly and air deflector. CAUTION The gas supply and electrical power must be shut off before proceeding with the conversion. TC36.NG05.C 290409-12... - Page 7 (Fig. #19) Fig. # 20 8. S lide the pilot adjustment band over and ensure that the hole in the orifice band is showing. (Fig. #20 shows NG position, Fig. # 21 shows LP position) Fig. #21 Fig. # 22 Remove the minimum rate screw located in the valve. (Fig. #22) Minimum rate screw TC36.NG05.C 290409-12...
- Page 8 Peel off the protective backing and apply the conversion label directly over the gas specifications on the rating label. Fig #26 14. A ttach the access panel to the side of the firebox with the previously removed screws. (Fig. #26) Note: Gasket must be installed with access panel. TC36.NG05.C 290409-12...
-
Page 9: Gas Pressure Check
Correct gas pressure requirement: Supply Pressure Natural Gas Propane (For purpose of input adjustment) Minimum 5.0" WC 12.5" WC Maximum 13.9" WC 13.9" WC Manifold Pressure Maximum 3.8" WC 11.0w" WC Minimum 2.1" WC 5.5" WC TC36.NG05.C 290409-12... -
Page 10: Flame Adjustment
Installation and Operating Instructions manual. 2. Remove the log set and set aside. 3. Loosen the screw in the Primary Air Shut- ter. 4. Rotate the shutter to increase or decrease the amount of primary air. 5. Reassemble in reverse order. Fig. # 31 PRIMARY AIR SHUTTER TC36.NG05.C 290409-12... -
Page 11: Replacement Parts
ITEM ..DESCRIPTION ..........PART NO. ITEM ..DESCRIPTION ..........PART NO. #4..PILOT ASSEMBLY ......5005.025 #1..TC36.NG05 BURNER ASSEMBLY ..TC36.NG05.C #2..9 PCS LOG SET ......... 5098.74611 #5..MAIN SUPPLY TUBE (FLEX) ..... 5019.223 #3..ORIFICE, NATURAL GAS (#30) ..5022.13 #6.. - Page 12 TECHNICAL SUPPORT: 1-888-715-2664 www.townandcountryfireplaces.net 2975 Allenby Rd., Duncan, BC V9L 6V8 Printed in Canada...