Provisiones especiales: Disposizioni speciali: Representative in the Union: Patrick Vervier, Stanley Dubuis 17-19, rue Jules Berthonneau-BP 3406 41034 Blois Cedex, France. Vertreter in der Union/Représentant dans l’union/Representante en la Union/Rappresentante presso l’Unione Done at/Ort/Fait à/Dado en/Fatto a Stanley Hydraulic Tools, Milwaukie, Oregon USA...
REPAIRS AND / OR SERVICE TO THIS TOOL MUST ONLY BE DONE BY AN AUTHORIZED AND CERTIFIED DEALER. For the nearest authorized and certified dealer, call Stanley Hydraulic Tools at the number listed on the back of this manual and ask for a Customer Service Representative.
Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULATIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel. 4 ► RS25 User Manual...
Long hair or loose clothing can become drawn the space provided in this manual. into rotating components. The model RS25 Hydraulic Rail Saw will provide safe • Always use accessories that conform to the speci- and dependable service if operated in accordance with fications given in the OPERATION section of this the instructions given in this manual.
Page 6
Stanley recommends wheels rated at 4700 RPM for 16 inch models and 5300 RPM for 14 inch mod- els.
SEE OTHER SIDE safety instructions listed on this tag before removal. We suggest you retain this tag and attach it to the tool when not in use. SAFETY TAG P/N 15875 (Shown smaller then actual size) RS25 User Manual ◄ 7...
HOSE SAFETY TAGS To help ensure your safety, the following DANGER tags are attached to all hose purchased from Stanley Hydraulic Tools. DO NOT REMOVE THESE TAGS.
2000 psi 2000 psi 2000 psi (at the power supply outlet) (172 bar) (138 bar) (138 bar) (138 bar) (138 bar) NOTE: These are general hydraulic system requirements. See tool specification page for tool specific requirements 10 ► RS25 User Manual...
A record of the speed checks 2. There should be no signs of leaks. should be maintained. The rated speed of the RS25 Rail 3. The tool should be clean, with all fittings and fasten- Saw is 3600 rpm at 10 gpm/38 lpm for the 16 inch/400 ers tight.
Readjust the lower link as required and Figure 3. finish the cut. 5. Tighten the bell crank to the rail by turning the clamp screw (75) clockwise. 12 ► RS25 User Manual...
Page 13
Wheels should not be stored where they will be exposed to high humidity, water, other liquids or freezing temperature. If wheels are supplied with blotters attached, suitable separators should be used to preserve flatness. RS25 User Manual ◄ 13...
This can cause damage to internal seals. • Always replace hoses, couplings and other parts with replacement parts recommended by Stanley Hydraulic Tools. Supply hoses must have a mini- mum working pressure rating of 2500 psi/172 bar. 14 ► RS25 User Manual...
Fluid leakage. Seal failure. Do not use. Have serviced by an authorized dealer. Off-center cut and binding. Bearings worn on link arms. Have unit serviced by an authorized dealer. Incorrect cutting technique. Review operating procedures. RS25 User Manual ◄ 15...
Includes 65625 Disconnect Pivot Bolt, 65626 Pivot Tube, 65627 Indicator Rod, 66133 Motor Assy) Motor Upgrade Kit 16 inch Model (After Serial No. 2598) .................66192 Includes 65625 Disconnect Pivot Bolt, 65626 Pivot Tube, 65627 Indicator Rod, 66134 Motor Assy) 16 ► RS25 User Manual...
28409 COMPOSITE STICKER (14 IN MODEL) 56708 CLAMP SCREW ASSY 25610 RAILROAD HELP DESK (16 IN MODEL) 03012 JAM NUT 28728 NAME TAG (14 IN MODEL) 62291 OUTER COLLAR 03787 GPM STICKER (16 IN MODEL) 18 ► RS25 User Manual...
Page 19
REFER TO ITEM 129 66138 RAIL CLAMP ASSY 11210 SOUND POWER STICKER 05152 LOGO-ADDRESS DECAL 66134 MOTOR ASSY 31845 SEAL KIT Item 133 (P/N-05152) Logo/Address Decal (UP Model Only) WHEEL GUARD 16 INCH “LOW SPARK” P/N-73168 RS25 User Manual ◄ 19...
Page 20
Stanley Hydraulic Tools 3810 SE Naef Road Milwaukie, Oregon 97267-5698 USA (503) 659-5660 / Fax (503) 652-1780 www.stanleyhydraulic.com...