Listen To The Tuner; Listening To The Radio; Station Preset Memory; Auto Memory - Kenwood KDC-610U Instruction Manual

9. Listen to the tuner

9-1. Listening to the radio

Selecting a tuner source
1
Press [SRC].
Enters the Source selection mode.
2
Select a Tuner ("TUNER") source using
[Control] knob.
Refer to <Source selection> (page 10).
Selecting a band (FM or AM)
Press [R].
Selecting a station
Press [E] or [F].
The seek mode can be changed. Refer to
<Selecting a Seek mode> (refer to below), <9-5.
Tuner setting> (page 27).
Selecting a Seek mode
Press [S].
Display Operation
"Auto1" Automatic search for a station.
"Auto2" Search in order of the stations in the preset memory.
"Manual" Normal manual tuning.

9-2. Station preset memory

You can store a station in the memory.
1
Press [E] or [F] to select the station.
2
Press [1/6].
Enter the Preset mode.
3
Turn [Control] knob to select a memory
number (FM: "1" – "18", AM: "1" – "6").
4
Press and hold [Control] knob.
Exiting from the Preset memory mode
Press and hold [1/6].
About the Mix Station preset mode
• If you press [1/6] twice in step 2, the Mix Station preset
mode is selected with "Mixed Preset List" displayed.
In this mode, different bands and tuner sources (FM, AM,
SiriusXM etc.) can be saved in the same preset layer, which
allows you to recall the desired station without switching
between bands or tuner sources.
A maximum of six stations can be preset in the Mix Station
preset mode.
Once the Mix Station preset mode is set, you can enter the
same mode by just pressing [1/6] once in step 2.
Pressing [1/6] twice allows you to return to the normal
Station preset mode.
26
|
KDC-610U

9-3. Auto memory

You can register 18 (FM)/ 6 (AM) stations with good
reception automatically.
1
Press [SRC] and select a Tuner ("TUNER")
source using [Control] knob.
Refer to <Source selection> (page 10).
2
Press [R] to select a band.
3
Press [Control] knob.
Enters the Function setting mode.
4
Select "Settings" > "Auto Memory" using
[Control] knob.
For how to use [Control] knob, refer to <3-3. How
to select the item> (page 9).
5
Select "YES" using [Control] knob.
When 18 (FM)/ 6 (AM) stations that can be received
are stored in the memory, the process in this mode
is completed.
Exiting from the Function setting mode
Press and hold [1/6].

9-4. Recall preset station

Recall the stations in the memory.
1
Press [R] to select a band.
2
Press [1/6].
Enter the Preset mode.
3
Select a memory number (FM: "1" – "18", AM:
"1" – "6") using [Control] knob.

9-5. Tuner setting

You can set up the tuner.
1
Press [SRC] and select a Tuner ("TUNER")
source using [Control] knob.
Refer to <Source selection> (page 10).
2
Press [Control] knob.
Enters the Function setting mode.
3
Select "Settings" using [Control] knob.
For how to use [Control] knob, refer to <3-3. How
to select the item> (page 9).
4
Select a Tuner setting item using [Control]
knob.
Display Description
"Seek Mode" Sets the seek mode.
"Auto1": Automatic search for a station.
"Auto2": Search in order of the stations in the preset
memory.
"Manual": Normal manual tuning.
"MONO" You can reduce the noise when stereo broadcasts are
received as monaural.
"ON" / "OFF"
"TI" Switches to the traffic information automatically when
the traffic bulletin starts.
"ON" / "OFF"
(Colored text: Factory setting)
5
Select a setting using [Control] knob.
Returns to the previous item.
Exiting from the Function setting mode
Press and hold [1/6].

9-6. Direct access tuning

(Function of remote control)
You can search for a station directly by entering
frequency.
1
Press [DIRECT] on the remote control.
"– – – –" appears and enter the Direct access tuning
mode.
2
Press the number buttons on the remote
control to enter the frequency.
Example:
Desired frequency Press the following buttons
92.1 MHz (FM) [9], [2], [1]
810 kHz (AM) [8], [1], [0]
3
Press [ENT] on the remote control.
Exiting from the Direct access tuning mode
Press [6] on the remote control.
|
English
27