Kärcher STH 10.66 C Operating Instructions Manual page 24

English
If there is no additional (higher)
•
hole or it is already in use, then
– Remove the V-belt cover (4).
– Hook spring (6) at the end of the
coupling cable into the next
highest hole (from 7a to 7b, from
7b to 7c).
– Replace V-belt cover.
Adjusting the shift lever
(STH 8.66, STH 10.66 C)
Figure 12
Remove spring clip (4) and washer
•
(5), extract spindle
nut (6) from the hole (7).
Press gearshift arm (2) down-
•
wards, set shift lever (3) to gear
"6".
Rotate spindle nut (6) in such
•
a way that the pin can be put into
the same hole (7).
Secure spindle nut with washer
•
and spring clip.
Adjusting the caterpillar track
(STH 10.66 C)
Figure 6
The caterpillar track (1) is correctly
adjusted if it can be forced down by
hand by 10–12 mm. If it can be
forced down by a greater or lesser
amount, it must be adjusted:
Set the machine on a secure and
•
horizontal support so that the
caterpillar tracks no longer touch
the ground.
Rotate nut (2) until the caterpillar
•
track has the correct tension:
– To tighten, rotate in clockwise
direction
– To slacken, rotate in anti-
clockwise direction.
Replacing the caterpillar track
(STH 10.66 C)
Figure 6
Set the machine on a secure and
•
horizontal support so that the
caterpillar tracks no longer touch
the ground.
Rotate nut (2) sufficiently in an
•
anti-clockwise direction to enable
the caterpillar track to be removed.
24
Replace caterpillar track and
•
adjust the tension of the new
caterpillar track with the nut (2)
(see "Adjusting the caterpillar
track").
Replacing a shear bolt
Figure 9
The worm (3) is fastened to the drive
shaft (4) with shear bolts (1) and
lock-nuts (2). The bolts are
constructed in such a way that they
break (shear off) if the worm strikes
solid extraneous objects. In this
way damage to the machine is
prevented. These bolts (1) and nuts
(2) may only be replaced with
original spare parts (two replace-
ment bolts and lock-nuts are
supplied with the machine):
Remove sheared-off bolt and nut,
•
clean place of attachment and
lubricate it.
Use a new shear bolt and lock-nut
•
to replace the broken one.
Replacing the clearing plate
(STH 5.56, STH 8.66, STH 10.66 C)
Figure 7
Remove screws (6), washers (7)
•
and nuts (8).
Replace clearing plate (5).
•
Screw new clearing plate to
•
housing with screws, washers
and nuts.
Replacing the clearing plate
(STH 953)
Figure 11
Tip machine backwards.
•
Remove screws (4) and nuts (5).
•
Replace clearing plate (2).
•
Screw new clearing plate to
•
housing with screws and nuts.
Tip machine back again, check
•
setting (see "Adjust clearing
plate").
Replace skids
Figure 7
Remove nuts (2), washers (3) and
•
bolts (4).
Replace skids (1) on both sides of
•
the housing.
Adjust new skids (see "Adjust the
•
skids").
Operating Manual – Snowthrower
Preparing the machine
for non-use
! Danger of causing an
explosion by fuel fumes igniting
Before you prepare the machine for
non-use, empty the fuel tank into a
suitable container in the open air
(see "Engine instructions").
When the machine is not to be used
for more than a month, e.g. after the
winter:
Prepare engine (see "Engine
•
instructions").
Clean machine.
•
To protect from rust, wipe over all
•
metal parts with an oily cloth or
spray with spray lubricant.
Park the machine in a clean, dry
•
enclosed space.
Warranty
The warranty terms issued by our
company or importer are valid in
every country.
We remedy faults to your machine
free of charge within the scope of the
warranty provided that the
cause proves to be a material or
manufacturing error. Should you
need to call upon the warranty,
please apply to the vendor of your
machine or to the nearest agency.