Related Manuals for Hobart FP Series
Summary of Contents for Hobart FP Series
- Page 1 Glass and dIshwashers Fp serIes InstallatIon and operatIon InstructIons wIth Vapo rInse eco Starting from Serial No.: 8651 xxxx reV. 02.03.2009...
- Page 2 1637-A-03-09...
-
Page 3: Table Of Contents
content Page Important notes ................ 4 InstallatIon ................5 .1 Location ..................5 . Electrical connection .................5 .3 Water connection ................5 .4 Drain connection ................5 controls ..................6 start-up ..................7 4.1 Detergent ..................7 4. Rinse aid ..................7 4.3 Priming the suction hoses ..............7 operatIon ................... -
Page 4: Important Notes
Important notes use in accordance with regulations This machine is exclusively to be used to wash ware such as plates, cups, glasses, cutlery, trays etc. do not use for electrically heated cooking and heat conservation appliances. safety Never hose down the machine. The "attention"... -
Page 5: Installation
InstallatIon locatIon – Wall clearence is not required. – Level machine by turning the feet. – Distribute machine weight equally onto all feet. Vapour may escape from the dishwasher door. Therefore adjacent furniture has to be protected to prevent swelling. electrIcal connectIon must be carried out by an authorized technician according to the local and national codes. -
Page 6: Controls
controls ➀ Machine on / oFF Pushing this button switches the machine on. As soon as the machine is ready for operation, the wash cycle is started by pushing this button also. By pushing and holding (3 seconds) this button, the drain and self cleaning cycle starts. -
Page 7: Start-Up
start-up deterGent do not use any acidic detergent products with the built-in detergent pump! (the ph-value has to be higher than 7.) – Place the suction hose into the detergent container. Fill the suction hose according to chapter 4.3. – the dosing pump can operate to a max. -
Page 8: Operation
start-up soFtener (only on option) For the first run, the softener has to be filled with regeneration salt and potable water. Filling the salt reservoir with cleaning agent will damage the water softener. – Open the door. – Unscrew the softener lid and fill the softener with 2 kg of "Granular regeneration salt"... -
Page 9: Run
operatIon – Remove any food debris before loading plates into rack. – Spray off greasy food soil. – Put rack into the machine and close the door. – Push the on/oFF button ➀ . During the wash cycle is running, the color of the on/oFF button changes from blue increasingly back to green. -
Page 10: Switch-Off And Cleaning The Machine
➈ lights up to indicate that an automatic hygiene cleaning of the machine interior should be carried out. – Before end of operation: Take out rack and put one HOBART-Hygiene-Cleaner Tab into the machine interior. – Close the door. –... -
Page 11: Preview Of Temperatures
preVIew oF temperatures – Press and hold (3 seconds) the program button ➁ until the actual temperatures (°c) are displayed (top = rinse, bottom = wash). The indicators go out 10 seconds after releasing the program button. Permanent temperature display can be activated on request by the service technician. -
Page 12: Settings And Counter Values
settInGs and counter Values attentIon: the machine has to be switched off. open the door. – If the door will be closed or if no button is pressed for 10 seconds, the indicator automatically switches off and the new settings will be saved. -
Page 13: Cycle Counter
settInGs and counter Values cycle counter – Push program button ➁ again. The display will show alternately "p" or the number of wash cycles. In the lower display ➄ appears the value up to 999. – ➅ Thousands will be shown in the upper Display Example: 103 wash cycles Max. -
Page 14: Activation / Deactivation Of Dryer
settInGs and counter Values actIVatIon / deactIVatIon oF dryer – Push program button ➁ again until "dry" is displayed. By pushing the on/oFF button ➀ – automatic drying can be activated / deactivated. – The lower Display ➄ shows "on" (activated) or "0FF" (deactivated). termInatIon oF settInG mode / counter dIsplay –... - Page 15 trouBleshootInG GuIde type oF FaIlure possIBle cause remedy poor wash result Dishes are not clean. Fine strainer soiled or obstructed by Take out fine strainer. If heavily soiled soak in a lime. vinegar solution. Then clean it thoroughly until the pores are free.
- Page 16 As continued product improvement is a policy of HOBART, specifications are subject to change without notice. Printed in Germany aG-21637-a-03-09-pc...