4iiii Sportiiiis User Manual
Heads-up display
Hide thumbs
Also See for Sportiiiis:
- Quick start manual (6 pages) ,
- User manual (2 pages) ,
- Quick start manual (2 pages)
Related Manuals for 4iiii Sportiiiis
Summary of Contents for 4iiii Sportiiiis
-
Page 1: Table Of Contents
1. Welcome to Sportiiiis 2. What’s in the Box 3. Getting to know Sportiiiis 4. Charging Sportiiiis 5. Personalize with the Sportiiiis Configuration Utility 6. Attach Sportiiiis to your Glasses 7. Pairing Sensors with Sportiiiis 8. Caring for Sportiiiis 9. Warranty and Support Page 1 Version 1.04... -
Page 2: Welcome To Sportiiiis
When properly mounted to your glasses, the boom of the Sportiiiis unit will be in your peripheral vision, so that its LEDs can tell you whether you are below, above, or in your zone by their color and position. - Page 3 Sportiiiis User Manual Multi-Function Button - The multi-function button is used to turn Sportiiiis on and off, as well as control a variety of other functions. It is activated by holding down the button until your unit announces the desired function. The table below describes the available button functions when Sportiiiis is powered off.
-
Page 4: Charging Sportiiiis
For best results, hold the unit with your middle finger and tap sharply with your index finger. You can adjust the sensitivity of TipTap in the Sportiiiis Configuration Utility. (See page 11 for more information) Charging Sportiiiis Page 4 Version 1.04... - Page 5 Sportiiiis User Manual To charge Sportiiiis, uncover the micro-USB port on the bottom of the unit and plug in the included USB 2.0 Charge/Sync Cable. Plug the other end of the cable into one of your computer’s USB ports or a USB power adapter.
-
Page 6: Personalize With The Sportiiiis Configuration Utility
Mac: launch the program from the applications folder (or system dock if you have copied a shortcut there). Note: If a newer version of firmware is available for your Sportiiiis unit the “update Firmware” dialog box will appear. Click “Flash new firmware” to continue. - Page 7 Zones – configuration of the LEDs Setup – hardware setup such as volume, brightness, etc. 2) Upload Status Button - whenever you make a change in the Sportiiiis Software Application, the Upload Status Button will indicate that it is “Ready to upload.”...
- Page 8 Sportiiiis User Manual The Profile Tab Enter your name, a “nickname” for your Sportiiiis unit, your email address, height, weight, year of birth, and gender in the Profile screen. Page 8 Version 1.04...
- Page 9 NOTE: For increased safety while cycling, it is recommended that you use the eye furthest from the road to view your Sportiiiis unit. Thus, in countries where you drive on the right side of the roadway, it is recommended that you mount your Sportiiiis unit under your right eye, and in countries where you drive on the left side of the roadway, you mount your Sportiiiis unit under your left eye.
- Page 10 Volume – typically a level of approximately 80-85 is acceptable under normal circumstances. Auto-Announce – interval at which your Sportiiiis unit will announce the current data from all paired sensors for which “Include in Auto-Announce” is selected (see Zones tab). To turn auto-announce off, move the slider all the way to the left.
- Page 11 User Manual Setup>Sensors Sensors that are currently paired with Sportiiiis will appear here, to delete a sensor click the “X” on the sensor entry. . Some sensors may have an area to input data, such as wheel circumference for a bike speed sensor as shown above.
- Page 12 User Manual Setup>TipTap Two important features of Sportiiiis are controlled by simply tapping on the side of the unit. A single tap will give you audio feedback of the current sensor being displayed and two taps will switch to the next sensor (if more than one sensor is paired). The slider adjusts the sensitivity of the TipTap function.
- Page 13 The Zone Adjustment widget - The Zone adjustment widget controls the 7 LEDs on the Sportiiiis boom and each LED is represented by a colored section with yellow nodes on their outer limits. Each zone’s start and end are changed bydragging the yellow nodes...
- Page 14 User Manual Example - Setting up a Zone workout: In this example, we’ll set up Sportiiiis for a run with a target heart rate zone of 130-140 bpm. a. Click and drag the yellow node on the left side of the target zone until the value in the corresponding box has reached 130.
- Page 15 Sportiiiis User Manual Speed/Pace Sensor Special Buttons Pace/Speed Selector – use to choose whether you’d like to use pace (minutes/mile(km)) or speed (miles(km)/hour) for footpods and bike speed sensors. Imperial/Metric – selects Imperial (miles) or Metric (kilometers) units. Page 15...
-
Page 16: Attach Sportiiiis To Your Glasses
For increased safety while cycling, it is recommended that you use the eye furthest from the road to view your Sportiiiis unit. Thus, in countries where you drive on the right side of the roadway, it is recommended that you mount your Sportiiiis unit under your right eye, and in countries where you drive on the left side of the roadway, that you mount your Sportiiiis unit under your left eye. - Page 17 Sportiiiis User Manual Sportiiiis Installation Page 17 Version 1.04...
-
Page 18: Pairing Sensors With Sportiiiis
1) Make sure that all ANT+ sensors that you would like to pair with are active* and within range (< 6ft) 2) With Sportiiiis off, hold down the button until you hear Sportiiiis say “Pairing” 3) Release the button - Sportiiiis will say “Start Pairing”... -
Page 19: Technical Support
Warranty 4iiii Innovations Inc. ("4iiii") warrants this product to be free from defects in material and workmanship, under normal use, for a period of one (1) year from the date of original purchase (the invoice date) to the original purchaser. Defects that...