Service Mode; Dvd Test Mode; Image Of The Test Mode; Image Of The Front End Test Mode - Pioneer AVH-P5000DVD/XN/UC Service Manual

1

6. SERVICE MODE

QQ
3 7 63 1515 0

6.1 DVD TEST MODE

Image of the test mode.

A
Test mode starting procedure
[SOURCE key] + [EJECT key] press
[2 key of remote control assy] press
Remote Control Assy SW
Start of the test mode.
TEST
(1)
B
FE test selection
Hereafter, to FE test
mode image.
[Note] In order to move on to another test after selecting a test (FE/EDC1/EDC2), it is necessary to restart the DVD mechanism in the test mode.

Image of the front end test mode.

C
TE
L 13942296513
FE test mode
0 x 00 0000
(1)
Power on FE offset coefficient
TE offset coefficient
D
AS offset coefficient
ENV offset coefficient
0FFF 0000
TG offset coefficient
DBAL coefficient
VIN1 offset cancel value
VIN2 offset cancel value
VIN3 offset cancel value
VIN4 offset cancel value
VIN5 offset cancel value
VIN6 offset cancel value
VIN7 offset cancel value
VIN8 offset cancel value
VIN9 offset cancel value
VIN10 offset cancel value
1 x 00 0000
(1)
F close
E
1FFF 0000
Focus close state
FEMAX level
www
FEMIN level
ASMAX level
ENVMAX level
FE normalization coefficient
Spindle gain coefficient
TEMAX level indication
TEMIN level indication
(2)
F
a
62
1
http://www.xiaoyu163.com
2
Legend:
[Note] Higher level 4 characters only. Lower level 4 characters are spaces.
(2)
EDC1 test selection
Hereafter, to EDC1
test mode image.
Legend:
(2)
Disc type DVD1
Disc type DVD2
layer
0000 0000 0100 0000
(3),(4)
(2)
CRG+/-
F search
S curve
measurement
Activates while the key
1A00 0000
is being pressed.
1B00 0000 : CRG+
(2)
1C00 0000 : CRG-
F search
1100 0000
x ao
y
. i
AVH-P5000DVD/XN/UC
2
http://www.xiaoyu163.com
3
8
Test mode stopping procedure Reset or ACC OFF-ON.
... Key operation
... Operation state
... The content displayed on the DVD mechanism (video only)
8 characters data is sent to the product side (HOST) by UART communication.
(3)
EDC2 test selection
Hereafter, to EDC2
test mode image.
... Key operation
... Operation state
... The content displayed on the DVD mechanism (video only)
8 characters data is sent to the product side (HOST) by UART communication.
Q Q
3 6 7 1 3
(3) (4)
Disc type CD
layer
0200 0000
(5)
LD-ON/OFF CRG_HOME
When LO-ON: 1100 0000
1D00 0000
When LD-OFF: 1000 000
[Note] If no action is taken for approximately 10 seconds after LD-ON, it will become LO-OFF automatically.
If F close is selected during LD-OFF, it will become an error.
During focus search (S character measurement mode), too, safety regulation applies if LD_OFF is not selected
within 10 seconds. Therefore, even if focus search is selected after LD-ON, it will become LD-OFF after 9 seconds.
In order to F close after focus search (S character measurement mode), set to Power_OFF first then power on again
before F close.
u163
.
3
4
2 9 9 4 2 8
(4)
LD power on time
mode selection
Hereafter, to LD power on
time mode image.
1 5 0 5 8 2 9
(5) EJECT
EJECT
Disc type CD-RW
0300 0000
(6) (8)
Power_OFF
m
co
4
9 9
9 4 2 8 9 9
b