Table of Contents
Advertisement
Quick Links
475 Barell Ave., Carlstadt, NJ 07072
Voice: 800-230-9497, 201-549-1160
Fax: 201-549-1161
INSTALLING THE 7400-5708 SHOW DMX VERO NET TRANSCEIVER
Installation
Install the SHoW DMX Vero Net Transceiver in a suitable location, following the instructions
below. When selecting a mounting location, note that for best results the antennas in your
system must be within sight of each other.
Warning
To avoid electric shock, do not energize any circuits before all internal and external electrical
and mechanical clearances are checked to assure that all assembled equipment functions
safely and properly.
Important use notes
This unit must be used with voltages below 600V
This unit must be installed in accordance with the National Electrical Code, ANSI/NFPA 70,
where the ambient temperature does not exceed 40°C (104°F) maximum.
Grounding
This enclosure has been provided with a ground bond jumper for ground connection between
the back box and the cover. This jumper must be installed as shown in the drawing below,
using the provided hardware.
Mounting Bracket
The provided mounting Bracket Base can be mounted on a surface or a vertical pipe. For
surface mounting, the Bracket base is provided with slots and holes suitable for #10 / M4
screws or similar fasteners.
Surface Mounting
Mount the Mounting Bracket Base in the desired location using four x #10 / M4 screws (by
others, as above).
7400-5708 Vero Net™ Transceiver
Installation and Quick Start Guide
© 2012, City Theatrical, Inc.
Page 1
Rev 1.2
Advertisement
Table of Contents
Related Manuals for City Theatrical 7400-5708 Vero Net
Summary of Contents for City Theatrical 7400-5708 Vero Net
- Page 1 7400-5708 Vero Net™ Transceiver Installation and Quick Start Guide Rev 1.2 © 2012, City Theatrical, Inc. 475 Barell Ave., Carlstadt, NJ 07072 Voice: 800-230-9497, 201-549-1160 Fax: 201-549-1161 INSTALLING THE 7400-5708 SHOW DMX VERO NET TRANSCEIVER Installation Install the SHoW DMX Vero Net Transceiver in a suitable location, following the instructions below.
- Page 2 Slide the mating Mounting Bracket (attached to the Unit) into the Mounting Bracket Base until the locking clip engages, and install the provided 8-18 x .500” SS Thread Forming Torx Button Head Security Screw, in the hole on the left side of the Bracket assembly. Mounting Orientation The 7400-5708 SHoW DMX Vero Net Transceiver must be mounted exclusively in an upright mounting position with the cable entries on the bottom and antenna connector on the top as...
- Page 3 Attach the Mounting Bracket Base to a pipe using a stainless steel hose clamp as shown: Slide the mating Mounting Bracket (attached to the Unit) into the Mounting Bracket Base until the locking clip engages, and install the retaining screw. Cable or Conduit Entry The unit enclosure is provided with ½”...
- Page 4 Mains Wire Installation and Termination Install the mains cable or conduit in the entry provided as shown in the drawing below. A liquid tight cable grip is provided for use with suitable outdoor rated cable with diameter range of .170”/4,3mm - .450”/11,4mm. When cable is used, strip outer jacket 6.0”/150mm.
- Page 5 Ethernet Cable entry The unit is provided with an RJ45 Ethernet Jack for Ethernet connection. Install the Ethernet able using the entry provided. An RJ45 Ethernet Plug must be installed on the Ethernet cable after the cable is pulled into the box, using the standard TIA-EIA T568B pin out. Installing the Cover The 7400-5707 SHoW DMX Vero Net Transceiver has a two part cover, with the outer plastic cover connected to the inner metal cover with a hinge.
- Page 6 Configu ration switches: P5, DMX Term: DMX 512 termination On or Off. Turn On for end-of-line DMX512 onnection. P4, Rx/Tx: Receiver (Rx) On, or Transmitter (Tx) Off. Selects Receiver or Transmitter peration 3, Reset: On or Off. Switch On to Reset P2 Bootloader: On or Off.
- Page 7 See the 7400-5708 SHoW DMX Vero Net Users Manual for more details about other system setting options. The Users Manual and the SHoW DMX Neo Installation and Application Guide can be downloaded from the City Theatrical website: www.citytheatrical.com. Page 7 of 7...
Need help?
Do you have a question about the 7400-5708 Vero Net and is the answer not in the manual?
Questions and answers