Table of Contents
Advertisement
Playback
Basic Playback
Turn on the VCR and TV, and select the VCR channel (or AV
mode).
A
Load a cassette
Make sure the window side is up, the rear label side is facing you
and the arrow on the front of the cassette is pointing towards the
VCR.
Do not apply too much pressure when inserting.
The VCR turns on, and the counter on the on-screen display is
reset, automatically.
If the cassette's record safety tab has been removed, playback
begins automatically.
B
Start playback
Press PLAY (
).
4
The S-VHS indicator lights up when you play back a tape
recorded in S-VHS mode or in S-VHS ET mode (
During playback
Stop playback
Press STOP (
) on the
8
Remote.
Pause playback and view still picture
Press PAUSE (
).
9
Press PLAY (
) to resume normal playback.
4
NOTE:
During still picture, vertical vibration may appear on the TV
screen. Press CH
/
on the Remote to get a clearer picture.
r
t
Pause and Frame-by-Frame playback
Press PAUSE (
) to pause, then press
9
repeatedly.
Press PLAY (
) to resume normal playback.
4
Picture Search
Press REW (
) or FF (
3
5
again to perform high-speed search.
Each time you press REW (
changes between low-speed and high-speed.
Press PLAY (
) to resume normal playback.
4
Variable-Speed Picture Search (including slow-motion)
Press
or
repeatedly.
2
6
Press PLAY (
) to resume normal playback.
4
Each time you press
2
changes. To decrease the speed during picture search, press the
opposite direction button repeatedly.
During still picture, press and hold
to start reverse) slow motion playback. When you release
2
the button, still picture resumes. During still picture, holding
PAUSE (
) for more than 2 seconds also starts forward slow
9
motion playback. If you press PAUSE (
resumes.
NOTE:
During slow motion, some noise may appear on the TV screen.
Press CH
/
on the Remote to eliminate the noise.
r
t
REC
PAUSE
PLAY
STOP/EJECT
pg. 11).
OR Press STOP/EJECT (
the VCR.
or
(or PAUSE (
2
6
). Press REW (
) or FF (
3
) or FF (
), the search speed
3
5
or
, the playback speed
6
to start forward (or
6
) again, still picture
9
Reverse
Reverse
search
3 steps
When the tape is not running
Rewind/fast-forward
Press REW (
Eject the cassette
Press STOP/EJECT (
You can also eject the cassette when the VCR is turned off.
Turn off the VCR
Press POWER 1.
Playback Features
Turn on the VCR and TV, and select the VCR channel (or AV
mode).
Adjusting tracking condition
— Tracking Adjustment
Automatic tracking adjustment
) on
0
Whenever you insert a tape and start playback, automatic tracking
starts working and continuously analyzes the signal to enable
optimum picture quality during playback.
Manual tracking adjustment
If automatic tracking cannot eliminate noises well during
playback, follow the procedures below.
On the Remote
A
Press SP/EP during playback to activate manual tracking.
B
Press CH
))
adjustment, or press and hold for a coarse adjustment.
9
Press SP/EP again to reactivate automatic tracking.
Selecting monitor sound
— Audio Monitor
)
5
While playing back a tape on which stereo sound or SAP sound is
recorded, press A.MONITOR on the Remote. Each time you press
the button, sound changes.
HI-FI: Normally select this. Hi-Fi sound is played back.
HI-FI L: Sound on the left Hi-Fi channel is played back.
HI-FI R: Sound on the right Hi-Fi channel is played back.
NORM: Sound on the normal track is played back.
NORM HI-FI: Both sounds on the Hi-Fi track and normal track are
mixed and played back.
NOTE:
The above indication appears when "SUPERIMPOSE" is set to
"ON" (
pg. 13), though the monitor sound changes in
sequence.
— 9 —
Reverse
Slow
Reverse
slow
motion
play
motion
1 step
1 step
) or FF (
).
3
5
).
0
/
to eliminate the noises. Press it briefly for a fine
r
t
CONTINUED ON NEXT PAGE
Forward
Forward
Normal
search
play
4 steps
Hide quick links:
Advertisement
Table of Contents
