Front Panel 3.2.4 MAC Filtering Back Panel 3.2.5 AirTies Mesh Settings Main Features INSTALLATION UPNP Cabling USB Devices Setup Media Server Advanced setup using AirTies Network Tools Assistant 3.7.1 2.3.1 Installation 3.7.2 2.3.2 Running Report AirTies Network Assistant 3.8.1 2.3.3 Network Display 3.8.2...
AirTies Mesh Technology is used for this purpose. The AirTies rights reserved. Manual Overview and reach the router on the wired network through the Mesh network. beginning the installation process. can be connected to the router by creating a wireless bridge between the two Air 4420s.
For Air 4420 Front Panel 1. One Air4420 2. One 12V Power Supplies 3. One Ethernet Cables 4. One Easy Setup CD 5. One Quick Installation Guide LIGHT STATUS Power Blue The device is ON The device is OFF LAN connection established and active Ethernet LAN connection active.
Make sure your gateway is turned on. Cabling Using the black Ethernet cable, connect the other Air 4420 to your TV, set-top box or games console. Connect the power adapters inside the box to the power sockets of each Air 4420 and plug into electric sockets.
Advanced setup using AirTies Network Assistant Your AirTies product will be provided with a CD that contains the AirTies Network www.airties.co . devices. 2.3.1 Installation During AirTies Network Assistant installation your AirTies device will be setup Ensure that you following the cabling for your product in according to the Your AirTies product will be provided with a CD that contains the AirTies Network www.airties.co .
Page 8
Ensure that you following the cabling for your product in according to the Click Next to setup your device.If your device and PC supports AirTouch then Press the AirTouch button on your AirTies device and click the AirTouch button. A secure connection will be initialised between the AirTies device and PC...
You can see the characters by unchecking Hide characters. Click Next . 2.3.2 Running The AirTies Network Assistant application will always run in the background AirTies Network Assistant select the AirTies Network Assistant Programs > AirTies Wireless Networks > AirTies Network Assistant.
2.3.3 Network Display Once AirTies Network Assistant has been installed and the connection between starts the network display will be shown. refresh can ran by clicking the refresh button on the top right of the screen. Network Assistant. Your router device is the device that has a connection to the Internet. It is should be investigated.
2.3.4 Change Node The properties can be displayed for each device. Properties for AirTies devices 2.3.5 Show Properties 2.3.6 Wireless Settings The password used to connect to the wireless network can be changed. This should be at least eight characters long. You can see the characters by unchecking Hide characters.
MESH. USB status shows whether a printer or USB disk is inserted into the device. 2.3.7 USB Status This will check for any newer versions of AirTies Network Assistant and update 2.3.8 Upgrade 2.3.9 User Info Firmware Upgrade.
(see settings below). 2.3.10 USB Host Click Next to install the printer. If a USB disk is attached to your AirTies device then a USB drive icon will 2.3.10 .1 USB Disk...
Ensure that the printer is connected to the device and click Next The printer will be created as a Windows printer. Click Print Test Page to test that the printer has been successfully setup. Cick Finish wireless switch on their PC. connected to your AirTies device.
When another device is added to the network then it will be displayed in the 192.168.2.154. 2.3.12 Adding Settings to register the device. AirTies Devices IP and DHCP Settings Click Edit to change the DHCP settings. network. Clicking OK resisters the new device.
Page 16
Enable DHCP Server DHCP Server DHCP Relay Agent DHCP Client devices. There must only be one DHCP Server on the network, which in most cases will be the router. DHCP is enabled by default. In this section you can assign an address range DHCP Server and enter an IP Save to save your settings.
Enable DHCP Relay Enable DHCP Client Agent server on the network. To enable DHCP client select DHCP Client. Click Save to save your settings. 2.1.2 LAN Clients needs to be known. clients connected to the device. Select LAN Client If DHCP Relay is enabled the DHCP server on your device is disabled and cannot assign IP addresses to clients.
Page 18
Static Addresses” Dynamic Addresses” table shows the IP addresses assigned but not VLAN 1. This is the entire network. reserved. To create a new VLAN click New VLAN. New” and select the LAN. Click save to create the new static address. Save to save your changes.
3.1.4 Port 3.2.2 Wireless VLANs. WIRELESS Wireless Connections screen that lists all Network Settings Select The Wireless Network Active box lets you enable or disable the wireless feature of your device. By default this is enabled. Save to save your changes. Wireless Settings With the N wireless technology you can set up a 300Mbps wireless network.
It is set to Auto MAC Address Filtering allows you to control which network cards can connect to the AirTies device and share your Internet access. For your wireless network encryption protocols be activated. Up to four separate SSIDs can be configured. By default one is configured. To add additional SSIDs you need to check the Enabled check box.
New MAC Address button. Click Save. Your AirTies device supports 802.1x Authentication protocol as well. For You can enter up to 4 network keys and choose the one you want to use. AirTies Website at www.airties.co Click Save.
3.2.5 AirTies Mesh Settings AirTies Mesh Technology resolves weak wireless signal and coverage area strength over long distances and through barriers such as concrete walls. barriers are resolved. Go to MESH under the WIRELESS Click Search AP that you would like your device to setup a Mesh connection with.
Important: To change the password used to protect the Web UI. Select Password Settings. UPNP Universal Plug and Play is a protocol that allows devices on the network Enter the current password and the new password twice. Select Save to save...
Your device supports USB disks and printers. If you want to use a USB device then you should plug the USB cable into your AirTies device. If a USB disk is attached then you should see the disk appear under USB Storage left hand side..
Update and clicking Save. You can check for updates by clicking Check For Updates Now. The device will contact AirTies to see if there are updates. If there are updates then they will Report Firmware Upgrade under the TOOLS Browse...
Page 28
AirTouch Three year warranty 24/7 people support 0845 557 5782 (from United Kingdom) +90 212 444 0239 (International) Visit for full list of technical support t...
Page 29
AirTies Air 4420-TV Описание Характеристики...
Need help?
Do you have a question about the Air 4420 and is the answer not in the manual?
Questions and answers