Jvc video cassette recorder instructions (44 pages)
Summary of Contents for JVC HR-J239EE
VIDEO CASSETTE RECORDER VIDEO PŘEHRÁVAČ MAGNETOWID KASET VIDEO HR-J239EE OPERATE PROG. CLOCK START STOP DATE DAILY (M-F) WEEKLY C.RESET CANCEL TIMER VOL. PROG. TV/VIDEO PLAY STOP OPERATE PUSH JOG AUTO SP/LP B.E.S.T. TIMER MULTI BRAND REMOTE CONTROL UNIT INSTRUCTIONS POKYNY...
Safety Precautions The rating plate and the safety caution are on the rear of the unit. WARNING: DANGEROUS VOLTAGE INSIDE WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. CAUTION When you are not using the recorder for a long period of time, it is recommended that you disconnect the power cord from the mains outlet.
INSTALLING YOUR NEW RECORDER Basic Connections Back of TV RF Cable (provided) Aerial AV-IN terminal terminals AV Cable (not provided) Mains Power Cord Mains outlet AUDIO OUT/ VIDEO OUT It's essential that your video recorder be properly connected. Follow these steps carefully. THESE STEPS MUST BE COM- PLETED BEFORE ANY VIDEO OPERATION CAN BE PER- FORMED.
If CH36 is occupied by a local station, adjust the RF output channel adjustment screw to use another channel between CH32 and CH40 instead. If some interference noise is continually seen on the screen, consult your JVC dealer. SET TEST/SYSTEM SWITCH Switch position Set to the appropriate position depending on your TV system.
INITIAL SETTINGS On-Screen Displays Turn on the TV and select the VIDEO channel (or AV mode). TV PROG.5∞ OSD ( The superimposed indication on the TV screen tells you what the recorder is doing. PR. 12 23 : 59 31. 12. 96 M –9 : 59 : 59 You can choose whether or not to have various operational indicators appear on screen, by setting this function ON or OFF.
Tuner Set Turn on the TV and select the VIDEO channel (or AV mode). TV PROG. INITIAL SETTINGS (cont.) Your recorder needs to memorise all necessary stations in channel positions in order to record TV programmes. Once stored, you can call them up with the TV PROG. buttons without going through any vacant channels.
SELECT POSITION Press TV PROG.5/∞ until an open position in which SELECT NUMBER you want to store a TV PROG. channel appears, then press OK. [TV PROG5∞] = [CH SET] :EXIT STORE CHANNEL If fine tuning is not necessary, simply press STORE.
INITIAL SETTINGS (cont.) Fine-Tuning Channels Already Stored TURN ON THE RECORDER Press OPERATE. ACCESS CHANNEL SET MODE SELECT SCREEN Press and hold CH SET for more than 2 seconds. The Channel Set Mode Select screen appears. SELECT MODE OPERATE Press TV PROG.5/∞ to place the pointer next to "FINE TUNING", then press OK.
Clock Set Turn on the TV and select the VIDEO channel (or AV mode). NUMBER5∞ TV PROG. TURN ON THE RECORDER Press OPERATE. ACCESS MODE SELECT SCREEN Press CLOCK. SELECT MODE Press TV PROG.5/∞ to place the pointer next to "CLOCK SET", then press OK on the remote control.
Basic Playback Turn on the TV and select the VIDEO channel (or AV mode). The easiest, most basic operation possible with your video recorder is tape playback. Already-recorded signals on a video tape are read by your video recorder and displayed on your TV just like a TV programme.
Playback Features Take advantage of special functions possible with the recorder’s controls or the remote control. Still Picture/Frame-By-Frame Playback PAUSE DURING PLAYBACK Press PAUSE. If there is vertical jitter, use the TV PROG. buttons to correct the picture. ACTIVATE FRAME-BY-FRAME PLAYBACK Press PAUSE.
Instant ReView Simply by pressing a single button, the recorder power comes on, rewinds, and begins playback of the last timer-recorded programme. If you have several programmes recorded, you can easily access any of them. NOTES: Before starting, make sure that the recorder is off and that the Timer mode is disengaged.
0:00:00 automatically. To cancel Counter Memory, press C.MEMORY again. Remote A/B Code Switching The remote control is capable of controlling two JVC video £ 2 recorders independently; one set to respond to the remote control’s A code control signals and another set to respond to B code control signals.
Basic Recording Turn on the TV and select the VIDEO channel (or AV mode). TV PROG. NUMBER SP/LP/EP RECORD TV signals being received by the recorder’s built-in tuner can be recorded onto a video tape. You can “capture” a TV programme using your video recorder.
Recording Features C.RESET TV PROG. Record One Programme While Watching Another SELECT CHANNEL TO WATCH Once recording is in progress, all you need to do is to set the channel controls on the TV for the station you wish to view. The programme selected with the TV’s channel controls appears on the TV screen while the one selected with the TV PROG.
B.E.S.T. Picture System Turn on the TV and select the VIDEO channel (or AV mode). B.E.S.T. indicator TV PROG. RECORD OSD ( The B.E.S.T. (Biconditional Equalised Signal Tracking) system checks the condition of the tape in use during recording and playback, and compensates to provide the highest-possible recording and playback pictures.
PAUSE RECORD NOTES: The B.E.S.T. system works for SP, LP and EP modes only after a tape has been inserted and the Record mode is first initiated. It does not work during recording. In the case of timer recording, the B.E.S.T. system works before recording is initiated.
Timer Programming Remember, the clock must be set before you can programme the timer ( pg. 9). AUTO SP/LP indicator NUMBER CANCEL SP/LP/EP Before performing the following steps: Insert a cassette with the safety tab in place. The recorder will come on automatically.
In case of a power failure after programming, the recorder’s memory backup keeps your selections for 18 hours. Backup time becomes shorter as the unit's internal parts become old. When this occurs, please consult your nearby JVC dealer. Check And Cancel Programmes ACCESS TIMER PROGRAM-...
Edit To Or From Another Video Recorder NUMBER "0" TV PROG. TV Receiver Player VIDEO CHANNEL RF Cable (provided) Another recorder Recorder You can use your video recorder as the source player or the recording deck. MAKE CONNECTIONS Connect the player’s AUDIO/VIDEO OUT connector to the recorder’s AUDIO/VIDEO IN connector.
Edit From A Camcorder NUMBER "0" You can use a camcorder as the source player and your video recorder as the recorder. MAKE CONNECTIONS Connect the camcorder’s AUDIO/VIDEO OUT connectors to the recorder’s AUDIO IN and VIDEO IN connectors. SET RECORDER’S INPUT MODE Press NUMBER key “0”.
SECAM signals will always be recorded as MESECAM. Select the AUTO or the MESECAM mode when recording SECAM signals. When playing back a SECAM tape, select the AUTO or the MESECAM mode. The playback picture will always be monochrome. HR-J239EE Recording circuit Multi-system MESECAM tuner (B/G, D/K) NTSC 3.58...
There are 4 different types of recorded tape, depending on the signal recorded. Recorded tape Playback equipment MESECAM MESECAM SECAM NTSC 3.58 MHz NTSC NTSC 4.43 MHz HR-J239EE Built-in RFconverter G, K HR-J239EE MESECAM Recording circuit SECAM NTSC 3.58 MHz NTSC 4.43 MHz...
Turn on the TV using its remote control. Set the remote control’s TV/VCR switch to TV. NOTE: If your TV is a JVC, you don’t have to set the code in step 1. Go to step 2. SET TV BRAND CODE Refer to the chart below.
Press TV PROG. 5 or ∞ a few times to remove the noise bars from the screen. The video heads may be dirty. Consult your JVC dealer. The wrong colour system is selected Select the correct colour system by for the tape being played back.
Turn the TV’s volume down. Recording is in progress. Press PAUSE to pause the recording, change channels, then press PLAY to resume recording. The TV/VCR switch is in the wrong Set the switch to TV. position. CORRECTIVE ACTION CORRECTIVE ACTION...
QUESTIONS AND ANSWERS PLAYBACK Q. What happens if the end of the tape is reached during playback or search? A. The tape is automatically rewound to the beginning. Q. Can the video recorder indefinitely remain in the still mode? A. No. It stops automatically after 5 minutes to protect the heads.
ABOUT HEAD CLEANING Accumulation of dirt and other particles on the video heads may cause the playback picture to become blurred or interrupted. Be sure to contact your nearest JVC dealer if such troubles occur.
DISPLAY PANEL SP LP R E C NTSC PLAY TIMER 1 PLAY Indicator ( pg. 10) 2 REC Indicator ( pg. 14) 3 NTSC Indicator ( pg. 22) 4 Tape Speed Indicators ( pg. 14) 5 Clock/Counter/Channel Display ( 6 ”Cassette Loaded” Mark 7 Counter Memory Indicator ( 8 ”Timer”...
The remote control can operate most of your video recorder's functions, as well as basic functions of TV sets of JVC and other brands ( Point the remote control toward the sensor window. The maximum operating distance of the remote control is about 8 m.