Page 1
BWD1409W 60 cm 9 kg Freestanding washer dryer...
Page 2
USER MANUAL FOR YOUR BAUMATIC BWD1409W 60 cm 9 kg Freestanding washer dryer NOTE : This User Instruction Manual contains important information, including safety & installation points, which will enable you to get the most out of your appliance. Please keep it in a safe place so that it is easily available for future reference;...
Contents Environmental note Important safety information 5 – 6 Specifications Description of the appliance 8 - 12 Control panel 9 - 10 LCD display Detergent drawer Preparing the wash cycle 13 - 15 Preparing your garments for washing A selection of wash care symbols Detergents and conditioners 14 - 15 Wash program table...
Environmental note o The packaging materials that Baumatic uses are environmentally friendly and can be recycled. o Please discard all packaging material with due regard for the environment.
General Safety o Repairs to your appliance must only be carried out by a Baumatic engineer or one of its authorised service agents. Any attempt by an inexperienced person to repair the appliance, could result in injury or damage to your washer dryer.
Page 6
If you use either dyes or bleaching agents inside this machine, then you should consult with the manufacturer of these products to make sure they are suitable for use in your washer dryer. Baumatic cannot be held responsible for any damage that may result. Child Safety o Your washer dryer should only be used by adults.
Specifications o 18 wash programs o 5 drying programs o 9 kg wash load o 7 kg drying load o 1400 rpm maximum spin speed o LED display o Delay start o Digital condensing dry system o Digital countdown indicator o Wash phase indicator o Tilted drum o Air bubble washing system...
Control panel 1) Power button. Press this button to turn the power on or off. 2) Start/pause button. Operation and temporary stop is repeated as it is pressed. When you want to change a program while it is in use, press this button, then select the program you want to change to, and then press this button again.
Page 10
5) Spin button. By pressing this button, the spin speed can be chosen. You can set the spin speed by rpm through the following options: Rinse Hold 1000 1400 6) Wash button. You can select the cycle you want by using this button.
LED display Wash cycle progress indicator This lights when a wash cycle is in progress, to indicate what stage of the wash cycle the appliance has reached from: Wash Rinse Spin Wash display This lights the wash functions that have been selected such as a pre- wash or a soak.
Detergent drawer Main wash section This compartment should have detergent placed in it (you should also put a water softening agent in this section, if you use one). The detergent will be added to the drum at the start of the main wash program.
Preparing the wash cycle Preparing your garments for washing o Your washing should be sorted out, according to the fabric type and the wash care symbol that is printed on the garment’s wash care label (see separate section on wash care symbols). o Your washing should also be sorted out according to the degree of soiling.
A selection of wash care symbols o The wash care symbols should be used to help you to select the most suitable wash program. They will also help you to sort your laundry into different loads, depending on the fabric type and the highest temperature which the garment can be washed at.
Liquid detergent If you are using liquid detergent, then in the majority of cases the liquid should be placed inside the dosing device supplied by the detergent manufacturer and placed inside the drum. All instructions on the detergent packaging should be followed. Water softening agents If your tap water is hard, then it may be prudent to utilise a water softening agent.
Pre Wash: If the laundry is heavily soiled, the pre-wash option is recommended. This option is available for cotton and synthetic wash programs. You should place detergent in the pre-wash compartment of the detergent drawer, as well as in the main wash compartment. Rinse+: Will introduce an additional rinse, which will help to remove traces of detergent residue.
Selecting a wash program Cotton program o Put the laundry into the drum and then close the door. The maximum load size is 9kg for a cotton wash. o In the detergent drawer, put detergent into the main wash and pre-wash compartments.
Page 18
Synthetic program o Put the laundry into the drum and then close the door. The maximum wash load size is below 3kg for the synthetic program. o In the detergent drawer, put detergent into the main wash and pre-wash compartments. o Put detergent into the pre wash compartment only if you want to use the pre-wash option.
Page 19
Delicate/ handwash program o Put the laundry into the drum and then close the door. The maximum wash load size is below 3kg for the delicate program. o In the detergent drawer, put detergent into the main wash compartment. o Softener should be poured into the middle compartment of the detergent drawer;...
Page 20
Intensive program o Put the laundry into the drum and then close the door. o Put detergent into the main wash and pre-wash compartments in the detergent drawer. Softener should be below the ‘MAX’ level. o Put detergent into the pre-wash compartment only if you want to add pre-wash.
Page 21
Use the wash program selection knob (3) to select the Quick 20 • program. A wash temperature of ‘cold’, with an 800 rpm spin will be • selected automatically by the appliance. * Press the start/pause button (2), the door will lock and after a few seconds you will hear the machine start to fill with water.
Page 22
* Press the start/pause button (2), the door will lock and after a few seconds you will hear the machine start to spin. Only wash o Put the laundry into the drum and put detergent and softener into the detergent drawer. Then close the door. o Press the power button (1) and the LED will show only “---“.
o Press the start/pause button (2) and the machine will begin the cycle after a few seconds. o For approximate drying times for each cycle, see the table below: Drying Cycle Approximate Time (hr.min) Time set 01.00 – 04.00 Low temperature 01.40 Iron 01.30...
o IMPORTANT: Changing the wash program will cancel any spin or temperature alterations that you have made and any program options that you have selected. You will need to make the spin/ temperature alterations again and re-select any program options that you require.
Child lock Your appliance has a child lock option, if this is set, it will mean that nobody can affect the operation of the wash program once it has started. o To activate the child-lock, press and hold the wash button (6) and the temperature button (4) at the same time for approximately three seconds.
o Wash the detergent drawer in warm, soapy water. For ease of cleaning, you can remove the upper part of the fabric softener compartment. o Detergent can also accumulate inside the detergent drawer recess, so you should also clean this out using a brush o Once you have finished cleaning the detergent drawer and recess, you should slide the drawer back...
o At the end of the wash cycle, you should leave the porthole door open for a short period of time. Cleaning the drain pump filter IMPORTANT: Switch off your washer dryer and disconnect the plug from your mains supply. You should clean out the filter approximately every ten washes.
IMPORTANT: If you are draining water from the bail hose and drain pump filter in an emergency. You should take care as the water coming from the machine mid-cycle could be hot. Especially if the water is being drained in the middle of one of the hotter wash cycles. Cleaning the water inlet filter o Clean the filter when water leaks from the water inlet.
Stain removal rules o Use warm water for soaking or pre-washing stained laundry. Hot water can set stains. o Most stains are easier to remove when they are fresh. o Before treating any stain try to establish; what kind of stain it is, how old the stain is, what the fabric type is and whether the fabric is colourfast (check the care label to find this out).
Grease Lay the affected area facedown on an absorbent cloth. Using white spirit or dry cleaning fluid, work on the back of the stain. Wash normally. Iron or rust Apply lemon juice and salt, and then place in the sun. Wash normally.
Installation IMPORTANT: THIS INSTALLATION MUST COMPLETED BY A SUITABLY QUALIFIED PERSON. BAUMATIC ONLY SANCTION INSTALLATION GIVEN THIS INSTRUCTION MANUAL. SHOULD KEEP THE TRANSIT PACKAGING, IN CASE YOU NEED TO TRANSPORT THE MACHINE IN THE FUTURE.
o Using spanner supplied, unscrew the 4 transit bolts. o You should keep the 4 transit bolts and spanners, in case you need to transport the appliance elsewhere in future. o Cover the holes that you removed the transit bolts from, using the 4 transit covers supplied.
o There should be a gap of 2 cm either side of the washer dryer; a 10 cm gap should be left behind the appliance. Connecting to the mains water supply IMPORTANT: The washer dryer should never be connected to the water mains using an existing inlet hose, YOU MUST utilise the inlet hose that is provided with the appliance.
or a screw-shaped tap onnecting to the water outlet Secure the drain hose, so that it cannot move whilst t he washer dryer is in use. Place the end of the drain hose on your drain pipe. Push it a short way down into your drain pipe.
NEVER EXTEND THE DRAINAGE HOSE FROM ITS ORIGINAL LENGTH. Levelling the appliance Place the washer d ryer on a solid and level floor surface. DO NOT PLACE THE WASHER DRYER ON A CARPET O SUSPENDED FLOOR. IMPORTANT: There should be no instability of the machine when the djustable legs have been set to the correct level.
ower supply IMPORTANT:The electrical socket must still accessible once the appliance is installed. Consult the rating plate, located on the inner rim of the porthole door or the right hand side of the cabinet BEFORE making electrical connections. Ensure that the voltage reaching the plug, is the same as that on the rating plate.
Error code failure system If your appliance senses that it is not operating correctly, then an error ode may appear on the LCD display. The following error codes can possibly be remedied by the customer nd the steps outlined below should be followed. BEFORE COMPLETING MAINTAIN...
POWER button. Disconnect appliance from your mains supply. Then arrange for an engineer to attend the appliance. You should contact Baumatic Customer Care Department on (0118) 933 6911. ENGINEER ATTENDS DURING GUARANTEE PERIOD AND FINDS THAT A FAULT...
Page 39
Or any installation other than the one specified by Baumatic Ltd. has been completed. lease refer to the conditions of guarantee that appear on the warranty card that you receive with the appliance.
Need help?
Do you have a question about the BWD1409W and is the answer not in the manual?
Questions and answers