Express Timer Programing; To Use The Vcr While It Is In Timer Recording Standby Mode; Checking, Canceling Or Changing Program Settings; Timer Recording - JVC HR-A57U Instructions Manual

Timer Recording

Up to 8 timer recording programs can be made using Express
timer programing method as far as a year in advance. Remember,
the clock must be set before you can program the timer.
NOTES:
● If all the 8 programs have already been set, "PROGRAM FULL"
or "Full" appears on the TV screen or the display panel.
● After timer recording is completed, the VCR turns off
automatically.
● You can program the timer recording while a regular recording
is in progress; the menu screens will not be recorded.
● To timer-record cable or satellite channels, be sure to keep the
cable box or DBS receiver turned on with the correct channel
selected.
● Even if a power failure occurs, the VCR keeps your timer
programs. However, the clock time, channel settings, and other
menu settings are lost. As a result, when the power is supplied
again to this VCR after the power failure, this VCR starts the
Plug&Play setting automatically to restore the clock time and
channel setting. If the clock time and channel setting are
restored correctly, each timer program you have made will start
at its start time unless its end time has elapsed.

Express Timer Programing

Load a cassette with the record safety tab intact. The VCR turns
on, and the counter is reset, automatically.
A
Press PROG. on the Remote to access the Program screen.
B
Press START+/–, STOP+/–, DATE+/–
or CH+/– repeatedly to enter the start
time, stop time, date or channel.
● Press and hold START+/– or
STOP+/– to increase the time in
30-minute intervals.
● To set the tape speed, press SP/EP
( ).
p
● To timer-record daily (Monday–Friday) or weekly serials,
press DAILY (M-F) or WEEKLY. Pressing the button again
makes the "DAILY" or "WEEKLY" display disappear.
PROGRAM 1
START STOP
– –:– –AM – –:– –AM
DATE CH
– –/– –/– – – – – SP
PRESS (+/–, SP/EP, 8=DAILY
9=WEEKLY), THEN (0K)
PRESS (PROG.) TO END
C
Press OK or PROG..
● If "PROGRAM NOT COMPLETED PROGRAM OVERLAP"
appears, see "Program overlap warning display".
D
Press TIMER. The VCR turns off automatically and "
displayed on the display panel.
To use the VCR while it is in timer
recording standby mode
Press TIMER, then press POWER. After you use the VCR, press
TIMER again to put the VCR into timer recording standby mode.
Checking, canceling or changing
program settings
A
Disengage timer
Press TIMER, then press POWER.
● When "AUTO TIMER" is set to "ON", you do not have to press
TIMER.
B
Access Program Check screen
Press PROG. CHECK.
C
Access Program screen
Press PROG. CHECK again. Each time you
press PROG. CHECK, the next program's
Program screen appears.
D
Cancel or change program setting
To cancel a program, press CANCEL when the Program screen
you do not want is shown.
To change a program, press the appropriate button: START+/–,
STOP+/–, DATE+/–, CH+/–, and/or SP/EP (
Program screen on which you want to make changes is shown.
E
Return to normal screen
Press PROG. CHECK repeatedly until no Program screen is
shown.
F
Reengage timer recording standby mode
Press TIMER. The VCR turns off automatically and "
displayed on the display panel.
● When "AUTO TIMER" is set to "ON", the timer recording
standby mode automatically resumes when you turn off the
VCR.
" is
#
PR START STOP CH DATE
1 8:00P 10:00 12 12/24
2 10:00A 10:45 40 12/25
3 11:30P 1:00 125 12/25
4
5
6
7
8
PRESS (CHECK) TO NEXT
PROGRAM 1
START STOP
8:00 PM 10:00 PM
DATE CH
12/24/00 12 SP
PRESS (CANCEL) TO CANCEL
PRESS (CHECK) TO NEXT
) when the
p
" is
#