Table of Contents
Advertisement
Sound Adjustments
7
Front speaker output balance
—"BAL (balance)"
DIGITAL AUTO
L
If the sounds you hear from the front right and left speakers are
unequal, you can adjust the speaker output balance.
Adjust the output balance appropriately from the listening
point within the range of R (Right) –21 to CENTER (0) or
CENTER (0) to L (Left) –21.
Note:
• "CENTER" is the initial setting. If you have already changed
the setting, another setting will be shown.
7
Tone—"BASS" and "TREBLE"
DIGITAL AUTO
L
DIGITAL AUTO
L
You can adjust the bass and treble sounds as you like.
Adjust the tone within the range of –10 to +10 in 2 steps
intervals.
Note:
• "0" is the initial setting. If you have already changed the setting,
another setting will be shown.
Adjusting sound from the remote control
1 Press CONTROL repeatedly
so that "SOUND" appears
on the operation mode
display.
Number buttons now work for sound adjustments.
2 Adjust the level as follows:
To adjust subwoofer, press SUBWOOFER + or –.
To adjust center speaker, press CENTER + or –.
To adjust left rear speaker, press REAR•L + or –.
To adjust right rear speaker, press REAR•R + or –.
To adjust the effect level (for DAP mode), press EFFECT.
About auto memory
This unit memorizes the settings for each source:
• when you turn off the power (see page 11)
• when you change the source (see page 11)
• when you change the analog/digital input mode (see page 13)
• when you change the source name (see page 14)
When you change the source, the memorized settings for the
newly selected source are automatically recalled.
SPK.
R
SPK.
R
SPK.
R
DVD AUDIO/VIDEO RECEIVER
7
Speaker output levels—"SUBWFR
(subwoofer)," "CENTER," "REAR L (left),"
and "REAR R (right)"
VOLUME
DIGITAL AUTO
L
R
SUBWFR
DIGITAL AUTO
L
C
R
DIGITAL
SUBWFR
LFE
LS
RS
DIGITAL AUTO
DIGITAL
L
C
R
SUBWFR
LFE
LS
RS
DIGITAL AUTO
DIGITAL
L
C
R
SUBWFR
LFE
LS
RS
You can adjust the speaker output levels if you have set the
speaker information appropriately.
• You can adjust the output level for center and/or rear speakers
VOLUME
only when one of proper Surround modes is activated (see
page 31).
Adjust the speaker output level within the range of –10 to
VOLUME
+10 in 1 step interval.
Note:
• "0" is the initial setting. If you have already changed the setting,
another setting will be shown.
7
DAP effect level—"EFFECT"
ANALOG
L
R
SUBWFR
LS
RS
While one of DAP modes is activated (the DSP indicator lights
up on the display), you can adjust the effect level.
For details about DAP modes, see pages 29 to 32.
Adjust the effect level within the range of 1 to 5.
Note:
• "3" is the initial setting. If you have already changed the setting,
another setting will be shown.
The following can be stored for each source:
• Analog/digital input mode (see page 13)
• Input attenuator mode (see page 14)
• Front speaker output balance (see above or page 56)
• Speaker output level (see above or page 57)
• Tone adjustment (see above or page 56)
• DAP effect level (see above)
• Surround mode selection (see page 31)
Note:
• If the source is FM or AM, you can assign a different setting for
each band.
SPK.
SPK.
SPK.
SPK.
DSP
SPK.
VOLUME
VOLUME
VOLUME
VOLUME
VOLUME
28
Advertisement
Table of Contents
