Subscribe to Our Youtube Channel
Related Manuals for Leggett & Platt E-95MR
Summary of Contents for Leggett & Platt E-95MR
- Page 1 99300791-d EDR12010 9/12 E-95MR remote control operation guide n English / Spanish [ adjustable bases ]...
- Page 3 E-95MR Function ......................4 Receiver Unit Programming ..................5 E-95MR Programming (1 remote control - 1 base) ............6 E-95MR Programming (2 remote controls - 1 base) ............7 E-95MR Programming (1 remote control - 2 bases) ............8 E-95MR Programming (2 remote controls - 2 bases) ............
- Page 4 30 minutes. note REMOTE CONTROL REqUIRES FOUR (4) AAA SIzE BATTERIES. TO CONSERVE BATTERY LIFE, THE TRANSMITTER TURNS OFF ALL FUNCTIONS WHEN ANY BUTTON IS PRESSED FOR MORE THAN 50 SECONDS. E-95MR Remote Control Operation Guide 99300791-d...
- Page 5 PRESS IN (SLIGHTLY) AND INDICATED INSIDE BATTERY COMPARTMENT PUSH DOWN TO REMOVE BATTERY COMPARTMENT DOOR DOOR INSTALLATION: PRESS COMPARTMENT DOOR AGAINST THE BATTERY ENDS, SLIDE DOOR UP AND IN TO ENGAGE THE DOOR TABS TABS E-95MR Remote Control Operation Guide 99300791-d...
- Page 6 ReMote contRoL pRogRaMMing (1 remote control - 1 base) Program One Remote to Operate One Base - your adjustable base will be equipped with one of the following: (A) a DC motor with a power down box, (B) an AC J box, (C) a DC motor without a power down box (FIGURE 2).
- Page 7 ReMote contRoL pRogRaMMing (2 remote controls - 1 base) Program Two Remotes to Operate One Base - your adjustable base will be equipped with one of the following: (A) a DC motor with a power down box, (B) an AC J box, (C) a DC motor without a power down box (FIGURE 2).
- Page 8 ReMote contRoL pRogRaMMing (1 remote control - 2 bases) Program One Remote to Operate Two Bases - your adjustable base will be equipped with one of the following: (A) a DC motor with a power down box, (B) an AC J box, (C) a DC motor without a power down box (FIGURE 2).
- Page 9 ReMote contRoL pRogRaMMing (2 remote controls - 2 bases) Program Two Remotes to Operate Two Bases - your adjustable base will be equipped with one of the following: (A) a DC motor with a power down box, (B) an AC J box, (C) a DC motor without a power down box BASE 1 (FIGURE 2).
- Page 10 ReMote contRoL pRogRaMMing (separating 2 bases) Program Two Remotes to Operate Two Bases - your adjustable base will be equipped with one of the following: (A) a DC motor with a power down box, (B) an AC J box, (C) a DC motor without a power down box (FIGURE 2).
- Page 12 Función E-95MR ......................4 Programación de la unidad receptora ................5 Programación de E-95MR (1 control remoto - 1 base) ............. 6 Programación de E-95MR (2 controles remotos - 1 base) ..........7 Programación de E-95MR (1 control remoto - 2 bases) ............ 8 Programación de E-95MR (2 controles remotos - 2 bases) ..........
- Page 13 EL CONTROL REMOTO REqUIERE CUATRO (4) PILAS TAMAñO AAA. PARA ALARGAR LA VIDA DE LAS PILAS, EL TRANSMISOR APAGA TODAS LAS FUNCIONES AL PRESIONAR CUALqUIER BOTóN POR MáS DE 50 SEGUNDOS. Guía de Operación de Control Remoto E-95MR 99300791-d...
- Page 14 INSTALACIóN DE LA TAPA: PRESIONE LA PUERTA DEL COMPAR- TIMIENTO CONTRA LOS EXTREMOS DE LA PILA, DESLICE LA PUERTA HACIA ARRIBA Y ADEN- TRO PARA INSERTAR LAS LENGÜETAS DE LA PUERTA LENGÜETAS Guía de Operación de Control Remoto E-95MR 99300791-d...
- Page 15 (1 control remoto - 1 base) Programe un control remoto para operar una base - su base ajustable incluirá uno de los siguientes: (A) un motor DC con una caja de apagado (B) una caja de conexiones AC, (C) un motor DC sin una caja de apagado (FIGURA 2).
- Page 16 (2 controles remotos - 1 base) Programe dos controles remoto para operar una base - su base ajustable incluirá uno de los siguientes: (A) un motor DC con una caja de apagado (B) una caja de conexiones AC, (C) un motor DC sin una caja de apagado (FIGURA 2).
- Page 17 (1 control remoto - 2 bases) Programe un control remoto para operar dos bases- su base ajustable incluirá uno de los siguientes: (A) un motor DC con una caja de apagado (B) una caja de conexiones AC, (C) un motor DC sin una caja de apagado (FIGURA 2).
- Page 18 (2 controles remotos - 2 bases) Programe dos controles remoto para operar dos bases - su base ajustable incluirá uno de los siguientes: (A) un motor DC con una caja de apagado (B) una caja de conexiones AC, (C) un motor DC sin una caja de apagado (FIGURA 2).
- Page 19 Manténgalos presionados durante 5 CABEzA segundos y suéltelos. paso 3 Repita el Paso 1 y el Paso 2 con el control remoto 1. Nota: Espere 90 segundos antes de iniciar el Paso 4. FIGURA 3 Guía de Operación de Control Remoto E-95MR 99300791-d...
- Page 20 [ adjustable bases ] asseMbLed in usa nationwide custoMeR seRvice toll free: (800) 888-3078 lpadjustablebases.com © 2012 Leggett & Platt Adjustable Bed Group, a division of Leggett & Platt, Incorporated...
Need help?
Do you have a question about the E-95MR and is the answer not in the manual?
Questions and answers
how to program remote to go to preset levels automatically
To program the Leggett & Platt E-95MR remote to go to preset levels automatically, follow these steps:
1. Ensure Power Connection: Plug the adjustable base into a power source and wait 30 seconds.
2. Enter Programming Mode:
- On the remote, press and hold the horizontal position button and the head massage on/off button simultaneously.
- The transmission indicator light will first blink slowly, then rapidly, indicating programming mode.
- Hold both buttons for 5 seconds, then release them.
3. Repeat for Additional Remotes (if applicable): If using multiple remotes, repeat the steps above for each remote.
4. Wait Before Proceeding: Allow 90 seconds before using the preset functions.
This process sets the remote to recall preset positions automatically when the corresponding button is pressed.
This answer is automatically generated