Specifications Of Speaker Setup - Pioneer SX-SW404 Service Manual

5

7.1.2 SPECIFICATIONS OF SPEAKER SETUP

QQ
3 7 63 1515 0
1. Overview
Several types of speakers are planned to be used with this product, and according to speaker type, the sound-quality
parameters to be sent to the Digital Amplifier section are different. Since the parameters for the planned speaker types have
been written in the EEPROM, by simply selecting the speaker type, as shown below, speaker setting is completed.
2. How to select the settings
• Except SX-X360 (XBOX model)
1. While holding the VOL+ and STANDBY/ON keys on the Display unit pressed, connect the power cord to the wall outlet.
Note: If the power cord was disconnected immediately before, be sure to wait at least one minute before turning on the
power in this way. Otherwise, the unit may not operate properly.
Or, Immediately after the power is turned off (within 5 seconds after the "-OFF-" indication goes dark), simultaneously
hold the VOL+ and STANDBY/ON keys on the Display unit pressed for more than 3 seconds.
2. The power comes on; then the following indication appears.
3. Press the key corresponding to the speaker to be used to determine the setting. The power will automatically be turned off.
VOL- key
VOL+ key
AUDIO INPUT key
SURROUND key
STANDBY/ON key
Note: Be sure to select the setting corresponding to the model number of the speaker. (See the table below.)
Destination
Europe
(Continent)
Europe (UK)
North America SX-SW260/KUCXCN
TE
L 13942296513
General
• SX-X360 (XBOX model) only
No setting is required. After the power cord is plugged in, "XBOX" is automatically set.
Destination
Europe
North America SX-X360/KUCXCN
3. How to confirm the speaker setting
1. While holding the AUDIO INPUT and STANDBY/ON keys on the Display unit pressed, connect the power cord to the wall
outlet.
Note: If the power cord was disconnected immediately before, be sure to wait at least one minute before turning on the
power in this way. Otherwise, the unit may not operate properly.
Or, in the standby mode, simultaneously hold the VOL+ and STANDBY/ON keys on the Display unit pressed for
more than 3 seconds.
2. Enter Test mode.
3. Hold the AUDIO INPUT key pressed for more than 8 seconds.
4. The setting is displayed.
If no setting has been written in the EEPROM, "UNKNOWN" is displayed.
www
4. Error indication
When the unit is turned on without any speaker setting, a warning "NO SPTYP" will be displayed. Even with this warning
.
displayed, all key operation is possible. After a key operation, the display will return to this warning indication.
5
http://www.xiaoyu163.com
6
S P T Y P E
R E G U L A R
T A L L - 1
T A L L - 2
For Japan model
A V R A C K
Not used
: Flashing
Model Number
SX-SW404/WYXCN5
SX-SW606/WYXCN5
SX-SW505HX/WVXCN5
SX-SW560/KUCXCN
SX-SW303/WLPWXCN
SX-SW505/WLPWXCN
Model Number
SX-X360/WYXCN5, WVXCN5 XBOX
T A L L - 1
U N K N O W N
x ao u163
y
i
N O S P T Y P
6
http://www.xiaoyu163.com
2 9
8
Speaker setting
REGULAR
TALL-1
REGULAR
REGULAR
TALL-1
Q Q
3 6 7 1 3
For reference
REGULAR
TALL-1
Speaker setting
XBOX
.
SX-SW404
7
9 4 2 8
1 5 0 5 8 2 9 9 4
m
co
7
8
9 9
A
B
C
2 8 9 9
D
E
F
57
8