Cleaning The Engine And Deck - Craftsman 247.28905 Operator's Manual

CLEANING
THE ENGINE AND DECK
Anyfuel or oil spilledon the machineshouldbe wipedoff promptly.Do
NOTallowdebristo accumulatearoundthe coolingfins of the engine
or on anyother partof the machine.
IMPORTANT: The useof a pressurewasherto cleanyourtractoris
NOT recommended. I t maycause damageto electricalcomponents,
spindles,pulleys,bearingsor the engine.
A screwplug can be foundon yourtractor'sdeck surfaceas seenin
Fig. 13.This plug can be replacedwith a waterport to be usedas part
of a separately-available d eck wash system.
Thedeck wash systemis usedto rinsegrassclippingsfromthe deck's
undersideand preventthe buildupof corrosivechemicals.
NOTE: A deck wash systemcan be purchasedthroughthe retail
locationin which youpurchasedthis tractor.For moreinformation,
simplycall 1-800-4-MY-HOME®.
/'
/
Figure13
ADJUSTMENTS
Neverattemptto makeanyadjustmentswhilethe engineis running,
exceptwherespecifiedin the operator'smanual.
Leveling the Deck
NOTE: Checkthe tractor'stire pressurebeforeperforminganydeck
levelingadjustments. R eferto Tires inthe Serviceand Maintenance
sectionof this manualfor moreinformation regardingtire pressure.
Front To Rear
Thefront of the cuttingdeck issupportedby a stabilizerbar that can
be adjustedto levelthe deckfrom front to rear.Thefront of the deck
shouldbe between1A-inch a nd 3A-inch lowerthan the rear of thedeck.
Adjustif necessaryas follows:
1. Withthe tractorparkedon a firm,levelsurface,placethe leverfor
lifting the platformon the secondto the top notch(secondhighest
position)and rotatethe bladeas close to the dischargechannel
that is parallelto the tractor.
22
2. Measurethedistancefromthe front of the bladetip to the ground
and the rearof the bladetip to theground.Thefirst measure-
ment takenshouldbe between1A" a nd 3A" less thanthe second
measurement.Determine the approximatedistancenecessaryfor
properadjustmentand proceed,if necessary,to the next step.
3. Locatethe flangelock nuton thefront sideof thestabilizerbracket.
See Fig. 14.
• Tightenthe flangelock nut to raisethe front of thedeck;
• Loosenthe flangelock nutto lowerthe front of the deck.
f
Figure14
Side to Side
If the cuttingdeck appearsto be mowingunevenly,a sideto side
adjustmentcan be performed.Adjustif necessaryas follows:
1. Withthetractorparked onafirm,levelsurface,placethedeckliftlever
in the secondfrom thetop notch (secondhighestposition)and
rotatebothbladessothat they are perpendicular w ith the tractor.
2. Measurethedistancefromthe outsideof the left bladetip to the
groundand the distancefrom the outsideof the rightblade tip to
the ground.Bothmeasurements taken shouldbe equal.If they're
not, proceedto the nextstep.
3. Loosen,but do NOTremove,the hexcap screwon the left deck
hanger bracket.See Fig. 15.
4. Balancethedeck byusingawrenchtoturntheadjustmentgear(found
immediatelybehindthe hexcap screwjustloosened)clockwise/
up or counterclockwise/down. Thedeck isproperlybalanced
when bothbladetip measurements takenearlier are equal.
5. Retightenthe hexcap screwon the left deck hangerbracketwhen
properadjustmentis achieved.