Page 1: Specifications
DSC-P71/P71M SERVICE MANUAL US Model DSC-P71/P71M Level 3 Canadian Model AEP Model UK Model E Model Hong Kong Model Ver 1.2 2002. 11 Australian Model Chinese Model Korea Model Tourist Model Japanese Model DSC-P71 This service manual contains information for Japanese model as well.
Page 2 Destination Australian, Chinese, Korea, Tourist Note: DSC-P71M is the same as DSC-P71 (US model) except packing materials. Therefore, information about DSC-P71 (US model) in the text is applied. CAUTION U s e o f c o n t r o l s o r a d j u s t m e n t s o r p e r fo r m a n c e procedures other than those specified herein may result in hazardous radiation exposure.
Page 3: Table Of Contents
DSC-P71/P71M TABLE OF CONTENTS Section Title Page Section Title Page SERVICE NOTE PRINTED WIRING BOARDS AND ..............5 SCHEMATIC DIAGRAMS Self-diagnosis Display ............6 4-1. Frame Schematic Diagrams .......... 4-1 GENERAL Frame Schematic Diagram (1/2) ........4-1 Frame Schematic Diagram (2/2) ........4-3 4-2.
Page 4 DSC-P71/P71M Section Title Page Flange Back Check ............5-17 F No. Compensation ............5-18 Mechanical Shutter Adjustment ........5-18 Light Value Adjustment ..........5-19 Mixed Color Cancel Adjustment ........5-19 Auto White Balance 3200K Standard Data Input ..5-20 Auto White Balance 3200K Check 1 ......5-21 10.
Page 5: Service Note
DSC-P71/P71M SERVICE NOTE • NOTE FOR REPAIR Make sure that the flat cable and flexible board are not cracked of When remove a connector, don’t pull at wire of connector. bent at the terminal. It is possible that a wire is snapped.
Page 6: Self-Diagnosis Display
[Description on Self-diagnosis Display] Self-diagnosis display • C: ss: ss You can reverse the camera mal- function yourself. (However, con- tact your Sony dealer or local authorized Sony service facility when you cannot recover from the camera malfunction.) • E: ss: ss...
Page 7: General
If you have any questions about this product, WARNING Declaration of Conformity you may call: Trade Name: SONY Sony Customer Information Services Center To prevent fire or shock hazard, do Model No.: DSC-P71 1-800-222-SONY (7669) not expose the unit to rain or Responsible Party:Sony Electronics Inc.
Page 8: Before Using Your Camera
DSC-P71/P71M Attention for the Customers in Europe This product has been tested and found compliant with the limits sets out on the EMC Directive for using connection cables shorter than 3 meters. Attention The electromagnetic fields at the specific frequencies may influence the picture and sound of this camera.
Page 9 Exposing the LCD screen, the finder or the lens to direct sunlight for long periods may cause malfunctions. The auto zoom lens (for the DSC-P71 On illustrations Trademarks only) Illustrations used in this manual are of the DSC- •...
Page 10: Identifying The Parts
DSC-P71/P71M Identifying the parts (DSC-P71) Attaching the strap A POWER ON/OFF lamp (20) • Use a tripod with a screw length of less than 5.5mm (7/32 inch). You will be unable to B POWER button (20) firmly secure the camera to tripods having C Shutter button (26) longer screws, and may damage the camera.
Page 11: Preparing Batteries
Nickel-Metal Charging time Hydride battery • If the poles of the Nickel-Metal Hydride • Do not charge any other batteries except Sony batteries are dirty, the batteries may not Nickel-Metal Hydride batteries in the charger NH-AA-DI × 2 Approx. 13 charge properly.
Page 12: Inserting The Batteries
DSC-P71/P71M Charging the Nickel-Metal hydride batteries (continued) Battery remaining indicator The POWER SAVE function When the POWER SAVE function is As the battery power decreases with use, When the POWER SAVE function is set • The LCD screen will be darker than it is when...
Page 13: Using An External Power Source
DSC-P71/P71M Inserting the batteries (continued) Battery life and the number of DSC-P31 **With the LCD screen on, showing single images in order, one approximately every images that can be recorded/ R6 (size AA) Ni-MH (2) (supplied) three seconds played back...
Page 14: Turning On/Off Your Camera
• if you turn the power on when the Mode dial is set to , or SCN, the lens begins to move (DSC-P71 only). Please be careful not to touch the lens. Setting the date and time Mode dial...
Page 15: Inserting And Removing A "Memory Stick
DSC-P71/P71M Setting the date and time (continued) CLOCK SET CLOCK SET Y/M/D CLOCK SET Y/M/D Y/M/D M/D/Y M/D/Y M/D/Y D/M/Y D/M/Y D/M/Y 2002 / 2002 / 2002 / CANCEL CANCEL CANCEL , Choose the year, month, day, , Set the desired numerical , Choose “OK”...
Page 16: Deciding The Still Image Size And Image Quality
DSC-P71/P71M Deciding the still image size and image quality FINE 2048x1536 2048 (3 : 2) 1600x1200 1600x1200 1600 (3 : 2) FINE AUTO 1280 x 960 1280 x 960 STANDARD WHITE BAL 640 x 480 640 x 480 P.QUALITY MODE...
Page 17: Basic Still Image Shooting (Using Auto Adjustment Mode)
Do not cover the lens or flash with your the zoom, and the lens is moving, don’t touch fingers. the lens assembly (DSC-P71 only) (page 28). • If you remove your finger from the shutter, • When the Mode dial is set to , the exposure shooting will be canceled.
Page 18: Digital Zoom
It has only a 3x digital zoom. • The lens moves when the zoom feature is being There is no Digital zoom item in SET used (DSC-P71 only). Be very careful not to touch the lens. • When you are using digital zoom, you •...
Page 19 (the maximum recommended distance for this feature is 2.8m (9.2 ft.) (wide), 1.8m (5.9 • The amount of red-eye reduction possible ft.) (tele) in DSC-P71, 2.5m (8.2 ft.) in DSC- varies according to the individual. In P31, or the subject has weak contrast, the addition, the distance to the subject, and camera may not focus properly.
Page 20 (page 21), and the information will be inserted you press the (Flash mode)/ (Self-timer)/ in the format you chose. (Macro, DSC-P71) or (Spot light- • The “DIGITAL ZOOM” item is not displayed metering, DSC-P31), the image will be on the SET UP screen of the DSC-P31 displayed on the screen for approximately 2 (page 28).
Page 21: Landscape Mode
DSC-P71/P71M Shooting according to scene conditions (SCENE SELECTION) Twilight mode Twilight portrait mode Landscape mode MENU button , Turn the mode dial to SCN, and Twilight portrait mode Ordinarily shoot with the camera set to set press the MENU button.
Page 22: Viewing Images On The Lcd Screen Of Your Camera
DSC-P71/P71M Viewing still images Viewing images on the LCD screen of your Viewing single images camera Single Index Index (Single image display) (9 images display) (3 images display) APERTURE VALUE : F2.2 1/125 100-0028 2002 7 4 10:30 SHUTTER SPEED :...
Page 23: Viewing Images On A Tv Screen
DSC-P71/P71M Viewing images on a TV screen VIDEO OUT jack 100-0028 2002 7 4 10:30 FILE BACK/NEXT Video connecting cable TV/Video toggle switch (supplied) , Using the video connecting , Turn on the power of the TV , Turn the Mode dial to...
Page 24 DSC-P71/P71M Deleting images (continued) Deleting on the Index (9 images) screen 2048 DELETE CANCEL DELETE PROTECT PRINT DELETE CANCEL SELECT MENU button , Select “OK” using v on the , While an Index (9 images) , Select “SELECT” using b/B on...
Page 25: Formatting A "Memory Stick
DSC-P71/P71M Deleting on the Index (3 images) screen (continued) DELETE PRINT PROTECT CANCEL DELETE 100-0028 2002 7 4 10:30 100-0028 2002 7 4 10:30 • • MENU button , Press the MENU button, and , Select “OK” using v on the select “DELETE”...
Page 26: Copying Still Images To Your Computer
Recommended computer Provided as standard equipment copy images using an additional device. See environment the Sony Website for details. • If you connect two or more USB devices to Recommended Windows environment your computer at one time, some devices, OS: Microsoft Windows 98, Windows...
Page 27: Preparing Your Camera
USB connection. into a wall outlet (mains). • You can use the “PIXELA ImageMixer for Sony” software to copy images to your • For further details on the “Memory Stick,” see computer. To install this software, click page 23.
Page 28: Copying Images
2 Confirm if other devices are already installed. 1 Click “Device Manager.” 2 Double-click “ Other Devices.” 3 Confirm if there is a “ Sony , Click “Copy pictures to a folder , Click “Next.” DSC” or “ Sony Handycam” on my computer using with a mark.
Page 29 DSC-P71/P71M 4 Copying images (for Windows XP users) (continued) , Click to remove the , Specify the image file names to , Click “Nothing. I’m finished checkmark from any images be copied and the copy working with these pictures,” you do not want to copy to destination.
Page 30: Viewing The Images On Your Computer
“My Documents” folder on page 48. • When using Windows XP, click “Start”t“My Documents” in that order. • You can use the “PIXELA ImageMixer for Sony” software to view images on your computer. For details, see the software’s help files. 1-24...
Page 31: For Macintosh Users
“Memory Stick” from • You can use the “PIXELA ImageMixer for The “PIXELA ImageMixer” window Sony” software to copy images to your your camera during a USB connection. appears. computer and view the images on your...
Page 32: Adjusting The Exposure
DSC-P71/P71M Advanced still image shooting The value of the exposure adjustment Shooting techniques Adjusting the is displayed. In normal shooting, the camera makes exposure 2048 automatic exposure adjustments. Check the image to be shot, if it looks like the image –...
Page 33: Choosing A Focus Method
DSC-P71/P71M a Turn the Mode dial to either • When you are shooting movies (MPEG Choosing a focus MOVIE) and you choose Multipoint AF, the SCN, or distance to the center of the screen is estimated method as an average, so the AF works even with a b Press the MENU button.
Page 34: Setting The Distance To The Subject
SEPIA NEG.ART margin of error. Use them as guidelines only. • If you point the lens up or down, the error increases (DSC-P71 only). a Turn the Mode dial to Colored to look like an Made to look like a...
Page 35 DSC-P71/P71M To cancel Spot light-metering For the DSC-P31 Shooting multiple Press the MENU button again and select a Turn the Mode dial to , SCN, frames ” using b/B on the control button, “ select “OFF” then using v/V. The Spot b Press B ( –...
Page 36: Shooting Still Images
DSC-P71/P71M a Turn the Mode dial to • When Multi Burst images are played back on a Shooting in Multi camera without the Multi Burst feature, the 16 b Press the MENU button. frames will all be displayed at the same time, as...
Page 37: Enlarging A Portion Of A Still Image
DSC-P71/P71M Advanced still image viewing e Press the T zoom button Enlarging an image – Playback Enlarging a portion of repeatedly, the portion of the zoom a still image image selected in Step 4 will a Turn the Mode dial to be enlarged.
Page 38: Protecting Images
DSC-P71/P71M a Turn the mode dial to , and To stop the playback of the slide Rotating still images show display the image you want to Press the center z, select “EXIT” using B, rotate. Mode dial setting: then press the center z.
Page 39: Changing Image Size
You can change your images to the The resized image is recorded as the following sizes. newest file. 2048×1536 (DSC-P71 only), 1600×1200, 1280×960, 640×480 To stop the resizing process After the resizing is finished, the original In Step 5, select “CANCEL”, then press image is retained.
Page 40: Choosing Images To Print
DSC-P71/P71M Single images Index (9 images) screen Choosing images to a Turn the mode dial to a Turn the mode dial to print press the W zoom button once b Display the image you want to to switch to the Index (9 –...
Page 41: Shooting Movies
“MPEG MOVIE” (pages 55, 97). down. Control button “RECORDING” appears on the screen To shoot close-ups (MACRO) and the camera starts recording the (DSC-P71 only) MENU button image. Mode dial Turn the Mode dial to and follow the procedure on page 28.
Page 42: Deleting Movies
DSC-P71/P71M Deleting on the single Deleting on the Index (9 Deleting movies screen images) screen a Turn the Mode dial to a Turn the Mode dial to Mode dial setting: press the W zoom button once Control button b Select the image you want to to display an Index (9 images) delete using b/B.
Page 43: Editing Movies
DSC-P71/P71M Cutting movies <Example> Cutting a file numbered Editing movies MOV00002.MPG Control button MOV00001.MPG MOV00003.MPG Mode dial setting: MENU button With the Mode dial, you can cut movies, or Mode dial delete unnecessary portions of movies. This is the recommended mode to use when the MOV00002.MPG...
Page 44: Copying Movies To Your Computer
To copy movie files using “ImageMixer” You can copy movie files using the supplied “PIXELA ImageMixer for Sony” software. The operation is the same as the operation used to copy still images. For details, see the software’s help files.
Page 45: Troubleshooting
(pages 26, 74). on the LCD screen. The image is out of focus. • The subject is too close. p Set the macro recording mode (DSC-P71 only) when you shoot a subject that is within 50 cm (19 inches) from the lens.
Page 46 DSC-P71/P71M Symptom Cause Solution Vertical streaks appear • The smear phenomenon is occurring. p This is not a malfunction. when you are shooting a very bright subject. You cannot shoot images. • No “Memory Stick” has been inserted. p Insert a “Memory Stick” (page 23).
Page 47 • The copy procedure differs depending on your p Follow the copy procedure that your OS suggests (pages 48, 49, 54). p If you are using the “PIXELA ImageMixer for Sony” software, — click on HELP. The image cannot be p If you are using the “PIXELA ImageMixer for Sony”...
Page 48: Warnings And Messages
• The battery pack is discharged. when you turn off the adaptor (pages 14, 17, 19). camera. (DSC-P71 only) The lens gets fogged. • Condensation is occurring. p Leave the camera for about an hour and then try to use it again (page 99).
Page 49: Self-Diagnostics Display
(indicated by ss)will differ depending on the state of the camera. If your camera is not still functioning well after trying the countermeasure a couple of times, contact your nearest Sony service station and inform them of the 5-digit C:32:ss service code.
Page 50: Menu Items
DSC-P71/P71M Additional information Menu items Menu items that can be changed differ depending on the position of the Mode dial. The LCD screen shows only the items you can operate based on the current position of the Mode dial. Factory settings are indicated with x.
Page 51 DSC-P71/P71M When the Mode dial is set to (MOVING IMAGE is set to CLIP MOTION in the SET UP settings.) Item Setting Description 2.0 / 1.7 / 1.3 / 1.0 / 0.7 / Adjusts the exposure (page 56). 0.3 / x0 / 0.3 / 0.7 / 1.0 / 1.3 / 1.7 / 2.0...
Page 52: Set Up Items
– xON/OFF START – Starts the slide show CANCEL – Cancels the settings and execution of the slide show RESIZE 2048×1536 (DSC-P71) / Changes the recorded image size (page 71). (For single images only.) 1600×1200/1280×960/ 640×480/ CANCEL ROTATE (clockwise) / (counter- Rotates the still image (page 68).
Page 53 DSC-P71/P71M SETUP 2 Item Setting Description Selects the LCD brightness. This has no effect on the recorded images. BRIGHT xNORMAL BRIGHTNESS DARK LCD BACKLIGHT BRIGHT/ Selects the brightness of the LCD backlight. Selecting “BRIGHT” makes the screen bright and easy to...
Page 54: The Lcd Screen
SOLARIZE Q EV adjustment indicator (56) R Iris value indicator S Shutter speed indicator (89) T Macro (DSC-P71) (28) U Self-timer display (29) V Vibration warning indicator (89) W Menu/Guide menu (55) • When you press the MENU button, Menu/ Guide menu is toggled between display/don’t...
Page 55 K EV adjustment indicator (56) display (16) information. C White balance indicator (57) L Macro (DSC-P71) (28) D Picture effect indicator (60) M Self-timer indicator (29) E Spot light-metering aiming point N Menu/Guide menu (55) (61) •...
Page 56: Disassembly
DSC-P71/P71M SECTION 2 DISASSEMBLY • This set can be disassembled in the order shown below. DSC-P71 2-4. CABINET (FRONT) 2-1. CABINET (REAR) BLOCK ASSEMBLY BLOCK ASSEMBLY (Page 2-3) (Page 2-2) 2-8. MEMORY STICK 2-5. CABINET (UPPER) 2-2. PK-064 BOARD 2-7. LENS BLOCK ASSEMBLY...
Page 57: Cabinet (Rear) Block Assembly
DSC-P71/P71M Note: Follow the disassembly procedure in the numerical order given. 2-1. CABINET (REAR) BLOCK ASSEMBLY 8 Cabinet (rear) block assembly 7 FP-067 flexible board (CN701) 5 Claw 1 Screw (M2) 4 Claw 2 Screw (M2) 3 Two screws (M2) 2-2.
Page 58: Lcd Module
DSC-P71/P71M 2-3. LCD MODULE 4 Light guide plate block × 1 Two screws (1.7 5 LCD module 3 LCD retainer × 2 Two screws (1.7 2-4. CABINET (FRONT) BLOCK ASSEMBLY 2 Open the BT lid 1 FP-528 board (CN708) 3 Screw (M 2)
Page 59: Cabinet (Upper) Block Assembly
DSC-P71/P71M 2-5. CABINET (UPPER) BLOCK ASSEMBLY × 1 Screw (1.7 2 Three claws 5 Cabinet (upper) block assembly 4 Flexible board (CN706) 2-6. ST-075 BOARD 3 FP-530 flexible board (CN502) 1 Claw 4 ST-075 board...
Page 60: Lens Block Assembly
DSC-P71/P71M 2-7. LENS BLOCK ASSEMBLY 3 FP-072 flexible board (CN704) 6 Lens block assembly × 1 Screw (1.7 5 FP-074 flexible board (CN102) 4 Flexible board (CN201) 2-8. MEMORY STICK CONNECTOR 1 Connector (CN703) 2 Two screws (M1.7) 4 Memory stick connector...
Page 61: Board
DSC-P71/P71M 2-9. CD-392 BOARD × 1 Two screws (1.7 4 Seal rubber (K) 5 CD-392 board 3 Optical filter block 2-10. JK-231 BOARD 4 JK-231 board 3 FP-072 flexible board (CN203) 2 Fixed JK plate 1 Screw (M 1.7)
Page 62: Board
DSC-P71/P71M 2-11. SY-075 BOARD 6 SY-075 board 3 Connector (CN001) × 2 Two screws (1.7 4 DC jack 5 CH-109 board 1 Connector (CN904) [SERVICE POSITION (SY-075 BOARD: SIDE B)] Adjustment remote commander Note 1: Don't use the 12 pin flexible board of CPC-9 jig.
Page 63: Service Position (Sy-075 Board: Side A)
DSC-P71/P71M [SERVICE POSITION (SY-075 BOARD: SIDE A)] Memory stick connector Memory stick JK-231 board Lens block assembly DC-IN connector DC jack AC power adaptor CH-109 Cabinet (upper) block board assembly Adjustment remote commander SY-075 board Note 1: Don't use the 12 pin flexible board of CPC-9 jig.
Page 64: Circuit Boards Location
DSC-P71/P71M 2-12. CIRCUIT BOARDS LOCATION SY-075 PK-064 CD-392 ST-075 CH-109 JK-231 Board Name Function CD-392 CCD IMAGER CH-109 CAMERA PROCESS SY-075 CAMERA DSP, VIDEO, MEMORY, LENS DRIVE, SH DSP, FLASH MEMORY CLOCK GENERATOR, CONNECTOR, DC IN DC/DC CONVERTER ST-075 FLASH DRIVE...
Page 65: Flexible Board Location
DSC-P71/P71M 2-13. FLEXIBLE BOARDS LOCATION FP-067 Control switch block FP-528 FP-074 FP-530 FP-072 FP-529 2-10...
Page 66: Block Diagrams
DSC-P71/P71M SECTION 3 BLOCK DIAGRAMS 3-1. OVERALL BLOCK DIAGRAM CD-392 BOARD CH-109 BOARD SY-075 BOARD (1/2) PANEL UNIT LENS IRIS PK-064 BOARD (1/2) METER PANEL R PANEL R CCD OUT IC301 DATA BUS PANEL G PANEL G IC801 LCD901 CCD IMAGER...
Page 67: Camera Block Diagram 1
DSC-P71/P71M 3-2. CAMERA BLOCK DIAGRAM 1 1.1 Vp-p 116 µsec Q352 E (CN351 qj) REC CH-109 BOARD SY-075 BOARD (1/4) CD-392 BOARD 65 – 69 CN101 CN705 DATA BUS D00 – 15 ı 71 81 CN102 Q352 CN351 AD0 − AD13 CAMERA BLOCK 2 3.9 Vp-p...
Page 68: Camera Block Diagram 2
DSC-P71/P71M 3-3. CAMERA BLOCK DIAGRAM 2 SY-075 BOARD (2/4) PK-064 BOARD (1/3) CN701 CN901 (3/5) (1/4) 39 41 – 45 47 49 DATA BUS DATA BUS D0 – 15 XMS ACCESS LED D251 51 52 54 56 – 60 MSDIR/PTC (0)
Page 69: Lens Motor Drive Block Diagram
DSC-P71/P71M 3-4. LENS MOTOR DRIVE BLOCK DIAGRAM SY-075 BOARD (3/4) LENS ASSY CN202 SHUTTER+ MSHUT REF PRELAMP AF ON CAMERA BLOCK 2 SELF TIMER LED SHUTTER (3-6) MOTOR SHUTTER– LENS TEMP OUT LENS TEMP AD TEMP CAMERA BLOCK 2 XCAM DR PS...
Page 70: Video Flash Mode Control Block Diagram
DSC-P71/P71M 3-5. VIDEO FLASH MODE CONTROL BLOCK DIAGRAM PK-064 BOARD (2/3) BZ901 Q901 CN902 BUZZER BEEP BUZZER SP+/BEEP OUT CN901 (2/4) FR SI FR SO 460 mVp-p 1.9 Vp-p 1.3 Vp-p CAMERA XFR SCK XMS IN BLOCK 2 32.768 kHz 2.3 Vp-p...
Page 71: Lcd Block Diagram
DSC-P71/P71M 3-6. LCD BLOCK DIAGRAM PK-064 BOARD (3/3) 528 mVp-p 8.9 Vp-p 8.9 Vp-p 8.9 Vp-p 448 mVp-p 400 mVp-p IC801 LCD DRIVE IC801 rk REC/PB IC801 w; REC/PB IC801 ws REC/PB IC801 wf REC/PB (2/3) IC801 rh REC/PB IC801 rj REC/PB...
Page 72: Power Block Diagram 1
DSC-P71/P71M 3-7. POWER BLOCK DIAGRAM 1 ST-075 BOARD CAM 15V CAM −7.5V CN502 T501 CN707 Q501, 502 A 4.9V ST UNREG FLASH UNIT A 2.9V POWER BLOCK 2 D 2.9V Q505, (3-16) Q507, Q506 Q704 D 3.1V Q508 M 5V...
Page 73: Power Block Diagram 2
DSC-P71/P71M 3-8. POWER BLOCK DIAGRAM 2 CD-392 BOARD CH-109 BOARD SY-075 BOARD (2/2) CN102 CN301 PK-064 BOARD (2/2) CN705 CN101 CAM 15V CAM 15V CAM 15V CAM 15V IC401 FRONT CONTROLLER CAM −7.5V CAM −7.5V CAM −7.5V CAM −7.5V (1/3)
Page 74: Printed Wiring Boards And Schematic Diagrams
DSC-P71/P71M SECTION 4 PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS 4-1. FRAME SCHEMATIC DIAGRAMS FRAME (1/2) D902 SELF TIMER/ AF ILLUMINATOR OVF_NZM FP-528 CN351 CCD_TEMP CAM_-7.5V CN202 SHUTTER+ SHUTTER+ SHUTTER- SHUTTER- LENS BLOCK CD-392 BOARD IRIS- IRIS+ VSHT N.C. FOCUS_A- FOCUS_B-...
Page 75 DSC-P71/P71M FRAME (2/2) FLASH UNIT ST-075 BOARD CONTROL BZ901 BUZZER SWITCH BLOCK CN903 BL_L1 CN902 BEEP_OUT CVCHK_OUT FP-530 REG_GND N.C. REG_GND PK-064 BOARD CPC_IN BL_L2 CN701 CN901 PANEL_COM REG_GND REG_GND REG_GND REG_GND (FOR CHECK) REG_GND REG_GND REG_GND REG_GND UNREG REG_GND...
Page 76: Schematic Diagrams
DSC-P71/P71M 4-2. SCHEMATIC DIAGRAMS THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block) (For schematic diagrams) • Circled numbers refer to waveforms. • All capacitors are in µF unless otherwise noted. pF : µ...
Page 77: Ccd Imager
DSC-P71/P71M CD-392 (CCD IMAGER) • See page 4-39 for CD-392 printed wiring board. • See page 4-57 for waveforms. CD-392 BOARD CH-109 CCD IMAGER CN102 (THROUGH THE FP-074 FLEXIBLE) XX MARK:NO MOUNT (SEE PAGE 4-10) NO MARK:REC/PB MODE R:REC MODE...
Page 78: Camera Process)
DSC-P71/P71M CH-109 (CAMERA PROCESS) • See page 4-41 for CH-109 printed wiring board. CH-109 BOARD CAMERA MODULE(CH BLOCK) XX MARK:NO MOUNT R118 CN101 REG_GND TG_CLK REG_GND MCK12 R119 REG_GND REG_GND R109 R102 CA_AD12 CA_AD13 R110 R103 CA_AD10 CA_AD11 R111 R104...
Page 79: Sy-075 (1/8) (Camera Dsp)
DSC-P71/P71M SY-075 (1/8) (CAMERA DSP) • See page 4-43 for SY-075 printed wiring board. SY-075 BOARD (1/8) CAMERA DSP(HMS BLOCK 1/2) A_2.9V D_2.9V XX MARK:NO MOUNT CA_HD D_1.5V CA_HD CA_FD CA_FD VSUB_CONT VSUB_CONT REG_GND CA_AD13 CA_AD13 FB301 FB302 CA_AD12 R309...
Page 80: Sy-075 (2/8) (Video, Memory)
DSC-P71/P71M SY-075 (2/8) (VIDEO, MEMORY) • See page 4-43 for SY-075 printed wiring board. • See page 4-58 for waveforms. SY-075 BOARD (2/8) SIGNAL PATH VIDEO MEMORY L302 VIDEO SIGNAL 10uH SY-075 (8/8) A_2.9V (HMS BLOCK 2/2, A_2.9V CHROMA Y/CHROMA...
Page 81: Sy-075 (3/8) (Lens Drive)
DSC-P71/P71M SY-075 (3/8) (LENS DRIVE) • See page 4-43 for SY-075 printed wiring board. SY-075 BOARD (3/8) NO MARK:REC/PB MODE LENS DRIVE(LD BLOCK) XX MARK:NO MOUNT CN201 R236 DRIVE- R231 DRIVE+ R230 0.5% HALL- 0.5% R260 R233 BIAS+ (SUFFIX-12) BIAS-...
Page 82: Sy-075 (4/8) (Sh Dsp)
DSC-P71/P71M SY-075 (4/8) (SH DSP) • See page 4-43 for SY-075 printed wiring board. SY-075 BOARD (4/8) SH DSP(SH BLOCK 1/2) XX MARK:NO MOUNT NO MARK:REC/PB MODE SY-075 (8/8) D_2.9V D_2.9V C501 6.3V SY-075 (8/8) D_3.1V D_1.5V L502 10uH Q501...
Page 83: 5/8)
DSC-P71/P71M SY-075 (5/8) (FLASH MEMORY CLOCK GENERATOR) • See page 4-43 for SY-075 printed wiring board. • See page 4-58 for waveforms. R785 R788 SY-075 BOARD (5/8) MC_CLK1 XX MARK:NO MOUNT NO MARK:REC/PB MODE FLASH MEMORY CLOCK GENERATOR (SH BLOCK 2/2,GEN BLOCK) C784 0.1u...
Page 84: Sy-075 (6/8) (Connector)
DSC-P71/P71M SY-075 (6/8) (CONNECTOR) • See page 4-43 for SY-075 printed wiring board. SY-075 BOARD (6/8) CONNECTOR(CN BLOCK) XX MARK:NO MOUNT NO MARK:REC/PB MODE PK-064 (1/3) CN901 (THROUGH THE FP-067 FLEXIBLE) (SEE PAGE 4-27) CN701 CN706 REG_GND REG_GND XAE_LOCK_SW SY-075 (7/8) EVER_4.0V...
Page 85: Sy-075 (7/8) (Dc In)
DSC-P71/P71M SY-075 (7/8) (DC IN) • See page 4-43 for SY-075 printed wiring board. SY-075 BOARD (7/8) DC IN(DD BLOCK 1/2) XX MARK:NO MOUNT NO MARK:REC/PB MODE Q001 CPH6313-TL SWITCH CN001 R005 J001 C001 470k BATT/XEXT DC IN 0.022u LF001...
Page 86: Sy-075 (8/8) (Dc/Dc Converter)
DSC-P71/P71M SY-075 (8/8) (DC/DC CONVERTER) • See page 4-43 for SY-075 printed wiring board. SY-075 BOARD (8/8) UNREG_SCK UNREG_SCK UNREG_SO UNREG_SO XCS_DDCON DC/DC CONVERTER(DD BLOCK 2/2) XCS_DDCON SYS_DD_ON SY-075 (6/8) Q017 SYS_DD_ON MCH3306-TL-E XX MARK:NO MOUNT SWITCHING DD_CON_SENS L007 L015...
Page 87: Pk-064 (1/3) (Front Control)
DSC-P71/P71M PK-064 (1/3) (FRONT CONTROL) • See page 4-47 for PK-064 printed wiring board. • See page 4-59 for waveforms. PK-064 BOARD (1/3) NO MARK:REC/PB MODE R:REC MODE FRONT CONTROL(FR BLOCK) P:PB MODE ∗ :IMPOSSIBLE TO MEASURE THE XX MARK:NO MOUNT VOLTAGE AT THE MARKED POINTS.
Page 88: Pk-064 (2/3) (Lcd Drive, Timing Generator)
DSC-P71/P71M PK-064 (2/3) (LCD DRIVE, TIMING GENERATOR) • See page 4-47 for PK-064 printed wiring board. • See page 4-59, 60 for waveforms. PK-064 BOARD (2/3) XX MARK:NO MOUNT LCD DRIVE,TIMING GENERATOR(RGB/TG BLOCK) NO MARK:REC/PB MODE L803 10uH PANEL_13.5V 12.8...
Page 89: Jack
DSC-P71/P71M PK-064 (3/3) (CONTROL SWITCH) • See page 4-47 for PK-064 printed wiring board. JK-231 (JACK) • See page 4-51 for JK-231 printed wiring board. SIGNAL PATH JK-231 BOARD PK-064 BOARD (3/3) VIDEO SIGNAL Y/CHROMA JACK CONTROL SWITCH(SW1 BLOCK) XX MARK:NO MOUNT...
Page 90: Flash Drive)
DSC-P71/P71M ST-075 (FLASH DRIVE) • See page 4-53 for ST-075 printed wiring board. ST-075 BOARD FLASH DRIVE(ST BLOCK) XX MARK:NO MOUNT LND501 NO MARK:REC/PB MODE Q502 Q503 D502 XE_H T501 MCH3306-TL CPH3209-SONY-TL-E HAU160C030TP R:REC MODE SWITCH TRANS DRIVE R514 P:PB MODE 4.7M...
Page 91: Printed Wiring Boards
DSC-P71/P71M 4-3. PRINTED WIRING BOARDS THIS NOTE IS COMMON FOR WIRING BOARDS (In addition to this, the necessary note is printed in each block) (For printed wiring boards) • : Uses unleaded solder. • Chip parts. Transistor Diode • : Pattern from the side which enables seeing.
Page 92 DSC-P71/P71M CD-392 (CCD IMAGER) • For Printed Wiring Board. • :Uses unleaded solder. • CD-392 board is four-layer print board. However, the patterns of layers 2 to 3 have not been included in the diagram. • There are a few cases that the part isn't mounted in this model is printed on this diagram.
Page 93 DSC-P71/P71M CH-109 (CAMERA PROCESS) • For Printed Wiring Board. • :Uses unleaded solder. • CH-109 board is eight-layer print board. However, the pat- terns of layers 2 to 7 have not been included in the diagram. • There are a few cases that the part isn't mounted in this model is printed on this diagram.
Page 94 DSC-P71/P71M SY-075 (CAMERA DSP, VIDEO MEMORY, LENS DRIVE, SH DSP, FLASH MEMORY, CLOCK GENERATOR, DC/DC CONVERTER) • For Printed Wiring Board. • :Uses unleaded solder. • SY-075 board is eight-layer print board. However, the patterns of layers 2 to 7 have not been included in the diagram.
Page 95 DSC-P71/P71M 11, (21) (MS SOCET) 4-45 4-46 SY-075...
Page 96 DSC-P71/P71M PK-064 (FRONT CONTROL, LCD DRIVE, TIMING GENERATOR, CONTROL SWITCH) • For Printed Wiring Board. • :Uses unleaded solder. • PK-064 board is four-layer print board. However, the patterns of layers 2 to 3 have not been included in the diagram.
Page 97 DSC-P71/P71M (TALLY/ACCESS) (AE LOCK/FLASH) ZOOM (W) ZOOM (T) MODE DIAL (STRB/CHARGE) MENU DISPLAY/LCD CONTROL (MS ACCESS) RESET 4-49 4-50 PK-064...
Page 98 DSC-P71/P71M JK-231 (JACK) • For Printed Wiring Board. • :Uses unleaded solder. • JK-231 board is four-layer print board. However, the patterns of layers 2 to 3 have not been included in the diagram. • There are a few cases that the part isn't mounted in this model is printed on this diagram.
Page 99 DSC-P71/P71M ST-075 (FLASH DRIVE) • For Printed Wiring Board. • :Uses unleaded solder. • ST-075 board is four-layer print board. However, the patterns of layers 2 to 3 have not been included in the diagram. • There are a few cases that the part isn't mounted in this model is printed on this diagram.
Page 100: Waveforms
DSC-P71/P71M 4-4. WAVEFORMS CD-392 BOARD 7.9 Vp-p 1.1 Vp-p 116 µsec 116 µsec IC351 1, 2, 3 (CN351 5, 6, 7) REC Q352 E (CN351 qj) REC 7.9 Vp-p 116 µsec IC351 4, 5, 6 (CN351 8, 9, q;) REC 3.9 Vp-p...
Page 101 DSC-P71/P71M SY-075 BOARD 460 mVp-p 310 mVp-p Q301 E REC/PB IC651 6 REC/PB 4.0 Vp-p 330 mVp-p 27 MHz Q302 E REC/PB IC781 2 (X781) REC/PB 3.0 Vp-p 340 mVp-p 44 MHz Q303 E REC/PB IC781 4 REC/PB 450 mVp-p 4.3 Vp-p...
Page 102 DSC-P71/P71M PK-064 BOARD (1/2) 2.3 Vp-p 5.2 Vp-p 10 MHz IC401 wk REC/PB IC801 wj REC/PB 1.3 Vp-p 448 mVp-p 32.768 kHz IC401 ts REC/PB IC801 rh REC/PB 400 mVp-p 8.9 Vp-p IC801 w; REC/PB IC801 rj REC/PB 528 mVp-p 8.9 Vp-p...
Page 103 DSC-P71/P71M PK-064 BOARD (2/2) 4.2 Vp-p 11.4 MHz IC802 wj REC/PB 3.0 Vp-p IC802 rk REC/PB 4-60...
Page 104: Parts Location
DSC-P71/P71M 4-5. PARTS LOCATION no mark : SIDE A * mark : SIDE B CD-392 BOARD CH-109 BOARD SY-075 BOARD C325 * F004 * Q021 * R204 * C351 * C103 * C001 C326 * F005 * Q022 * R206...
Page 105 DSC-P71/P71M PK-064 BOARD JK-231 BOARD ST-075 BOARD * R710 Q805 R811 BT401 * CN201 C503 * R711 Q806 R812 * CN202 C504 R785 Q807 R813 C401 * C507 R786 Q808 R814 C402 * D201 C508 R787 Q809 R815 C403 * D206...
Page 106: Adjustments
DSC-P71/P71M SECTION 5 ADJUSTMENTS Before starting adjustment EVR Data Re-writing Procedure When Replacing Board The data that is stored in the repair board, is not necessarily correct. Perform either procedure 1 or procedure 2 or procedure 3 when replacing board.
Page 107: Adjusting Items When Replacing Main Parts And Boards
DSC-P71/P71M 1-1. Adjusting items when replacing main parts and boards When replacing main parts and boards, adjust the items indicated by z in the following table. Replaced parts Block Mounted parts Board replacement replacement replacement Adjustment section Adjustment Initialization of A, D page data...
Page 108: Camera Section Adjustments
DSC-P71/P71M 5-1. CAMERA SECTION ADJUSTMENT 1-1. PREPARATIONS BEFORE ADJUSTMENT 1-1-1. List of Service Tools • Oscilloscope • Color monitor • Vectorscope • Regulated power supply • Digital voltmeter Ref. No. Name Parts Code Usage Auto white balance adjustment/check Filter for color temperature correction (C14)
Page 109: Preparations
DSC-P71/P71M 1-1-2. Preparations Note 1: For details of how remove the cabinet and boards, refer Pattern box to “2. DISASSEMBLY”. Note 2: When performing only the adjustments, the lens block and boards need not be disassemble. 1) Connect the equipment for adjustments according to Fig. 5-1- 2) Connect the Adjusting remote commander to PK-064 board CN903 via CPC-9 jig (J-6082-393-C).
Page 110 DSC-P71/P71M Note 1: Don’t use the 12 pin flexible board of CPC-9 jig. It causes damage to the unit. Adjusting Note 2: The old CPC-9 jig (Parts code: J-6082-393-B) remote cannot be used, because it cannot operate commander the adjusting remote commander.
Page 111: Precautions
DSC-P71/P71M 1-1-4. Precautions 1. Setting the Switch Unless otherwise specified, set the switches as follows and per- form adjustments. 1. Mode Dial .......... CAMERA 2. ZOOM switch (PK-064 board S252, S254) ....WIDE end 3. EV (Menu display) ......0EV 4.
Page 112: Preparing The Flash Adjustment Box
DSC-P71/P71M 4. Preparing the Flash Adjustment Box A dark room is required to provide an accurate flash adjustment. If it is not available, prepare the flash adjustment box as given below; 1) Provide woody board A, B and C of 15 mm thickness.
Page 113: Initialization Of A, B, D, E, F
DSC-P71/P71M 1-2. INITIALIZATION OF A, B, D, E, F, 7, 9 PAGE 3. A Page Table Note 1: Fixed data-1: Initialized data. DATA (Refer to “1. Initializing the A Page Data”) 1-2-1. Initialization of A, D Page Data Note 2: Fixed data-2: Modified data.
Page 114: Initialization Of B, E, F
DSC-P71/P71M 1-2-2. Initialization of B, E, F, 7, 9 Page Data 3. B Page Table 1. Initializing B, E, F, 7, 9 Page Data Note 1: Fixed data-1: Initialized data. Note: If the B, E, F, 7, 9 Page data has been initialized, (Refer to “1.
Page 115 DSC-P71/P71M 5. F Page Table Note 1: Fixed data-1: Initialized data. (Refer to “1. Initializing the B, E, F, 7, 9 Page Data”) Note 2: Fixed data-2: Modified data. (Refer to “2. Modification of B, E, F, 7, 9 Page Data”)
Page 116: Page Table
DSC-P71/P71M Address Initial value Remark Address Initial value Remark Color reproduction adj. AWB 3200K standard data input AWB 5800K standard data input AWB 3200K standard data input AWB 5800K standard data input Strobe white balance adj. AWB 3200K standard data input Fixed data-1 (Initialized data) Strobe white balance adj.
Page 117: Video System Adjustment
DSC-P71/P71M 1-3. VIDEO SYSTEM ADJUSTMENT 1. Composite Video Level Adjustment Adjust the sync level of the composite video signal output and check the burst level of the composite video signal output. Mode PLAY Signal Arbitrary Measurement Point Video terminal of VIDEO OUT jack (75 Ω...
Page 118: Camera System Adjustments
DSC-P71/P71M 1-4. CAMERA SYSTEM ADJUSTMENTS After completing the camera system adjustments, release the data setting: Before perform the camera system adjustments, check that the specified values of “VIDEO SYSTEM ADJUSTMENTS” are sat- Order Page Address Data Procedure isfied. Note: For “CAMERA SYSTEM ADJUSTMENTS”, perform in order of item numbers.
Page 119: Picture Frame Setting
DSC-P71/P71M Picture Frame Setting How to reset the zoom and focus when they deviated: Order Page Address Data Procedure Mode CAMERA Subject Color bar chart (Standard picture frame with the zoom lens at WIDE end) Measurement Point Video terminal of VIDEO OUT (Note 2) jack (75 Ω...
Page 120: Flange Back Adjustment (Using The Minipattern Box)
DSC-P71/P71M 1. Flange Back Adjustment Adjusting method: RadarW RadarW RadarW (Using the minipattern box) Order Page Address Data Procedure The inner focus lens flange back adjustment is carried out auto- Perform “Data setting during matically. In whichever case, the focus will be deviated during camera system adjustment”.
Page 121: Flange Back Adjustment (Using The Flange Back Adjustment Chart And Subject More Than 500 M Away)
DSC-P71/P71M RadarW RadarW RadarW RadarW RadarW 2. Flange Back Adjustment 2-2. Flange Back Adjustment (2) (Using the flange back adjustment chart and Perform this adjustment after performing “Flange Back Adjust- Subject More than 500 m Away) ment (1)”. The inner focus lens flange back adjustment is carried out auto-...
Page 122: Flange Back Check
DSC-P71/P71M 3. Flange Back Check Mode CAMERA Subject Siemens star (1.0 m from the front of the lens) (Luminance: 200 to 400 lux) Measurement Point Check operation on monitor TV Measuring Instrument Specified value Focused at the TELE end and...
Page 123: F No. Compensation
DSC-P71/P71M RadarW RadarW RadarW RadarW RadarW RadarW 4. F No. Compensation 5. Mechanical Shutter Adjustment Compensate the unevenness of the iris meter sensitivity. Adjust the period which the mechanical shutter is closed, and com- pensate the exposure. Mode CAMERA Mode...
Page 124: Light Value Adjustment
DSC-P71/P71M RadarW RadarW RadarW RadarW RadarW RadarW RadarW RadarW 6. Light Value Adjustment 7. Mixed Color Cancel Adjustment Adjust the standard LV value. To perform mixed color cancel adjustment based on data of each color in color bar. Mode CAMERA...
Page 125: Auto White Balance 3200K Standard Data Input
DSC-P71/P71M 8. Auto White Balance 3200K Standard Data Input Processing after Completing Adjustment: RadarW RadarW RadarW RadarW RadarW Order Page Address Data Procedure Adjust the white balance standard data at 3200K. Press PAUSE button. Mode CAMERA Subject Clear chart (Standard picture frame with the...
Page 126 DSC-P71/P71M RadarW RadarW RadarW RadarW RadarW Processing after Completing Adjustment: 9. Auto White Balance 3200K Check 1 Order Page Address Data Procedure Mode CAMERA Press PAUSE button. Subject Clear chart (Standard picture frame with the zoom lens at TELE end)
Page 127: Auto White Balance 3200K Check 1
DSC-P71/P71M RadarW RadarW RadarW 10. Auto White Balance 3200K Check 2 Processing after Completing Adjustment: Mode CAMERA Order Page Address Data Procedure Subject Clear chart Press PAUSE button. (Standard picture frame with the zoom lens at TELE end) Measurement Point...
Page 128: Auto White Balance 5800K Standard Data Input
DSC-P71/P71M Processing after Completing Adjustment: 11. Auto White Balance 5800K Standard Data Input RadarW RadarW RadarW RadarW RadarW Order Page Address Data Procedure Adjust the white balance standard data at 5800K. Press PAUSE button. Mode CAMERA Subject Clear chart (Standard picture frame with the...
Page 129 DSC-P71/P71M RadarW RadarW RadarW Processing after Completing Adjustment: 12. Auto White Balance 5800K Check 1 Order Page Address Data Procedure Mode CAMERA Press PAUSE button. Subject Clear chart (Standard picture frame with the zoom lens at TELE end) Filter Filter C14 for color temperature...
Page 130: Auto White Balance 5800K Check 1
DSC-P71/P71M RadarW RadarW RadarW RadarW RadarW 13. Auto White Balance 5800K Check 2 Processing after Completing Adjustment: Mode CAMERA Order Page Address Data Procedure Subject Clear chart Press PAUSE button. (Standard picture frame with the zoom lens at TELE end)
Page 131: Color Reproduction Adjustment
DSC-P71/P71M RadarW RadarW RadarW 14. Color Reproduction Adjustment Adjust the color separation matrix coefficient so that proper color reproduction is produced. Mode CAMERA Subject Color bar chart (Standard picture frame with the zoom lens at WIDE end) Measurement Point Video terminal of VIDEO OUT jack (75 Ω...
Page 132: Ccd White Defect Compensation
DSC-P71/P71M RadarW RadarW RadarW RadarW RadarW 15. CCD White Defect Compensation Mode CAMERA Subject Not required Measurement Point Displayed data of page: 6, address: 55 Measuring Instrument Adjusting remote commander Note 1: Check that the data of page: 6, address: 02 is “00”.
Page 133: Ccd Black Defect Compensation
DSC-P71/P71M RadarW RadarW RadarW RadarW RadarW Processing after Completing Adjustment: 16. CCD Black Defect Compensation Order Page Address Data Procedure Mode CAMERA Press PAUSE button. Subject Clear chart (Standard picture frame with the zoom lens at WIDE end) Measurement Point...
Page 134: Ccd Linearity Check
DSC-P71/P71M RadarW RadarW RadarW RadarW RadarW 17. CCD Linearity Check Order Page Address Data Procedure Check that CCD output keeps being straight even ISO sensitivity Press PAUSE button. is changed. Check the data changes to Mode CAMERA “01”. Subject Clear chart...
Page 135: Strobe White Balance Adjustment
DSC-P71/P71M RadarW RadarW RadarW RadarW RadarW 18. Strobe White Balance Adjustment Order Page Address Data Procedure Adjust the white balance when the strobe light flashed. Press PAUSE button. Mode CAMERA Check the flashing. Subject Flash adjustment box (Note 3) Check the data changes to (50 cm from the front of lens) “01”.
Page 136 DSC-P71/P71M Processing after Completing Adjustment: Order Page Address Data Procedure Press PAUSE button. “Set data noted down at step 3, and press PAUSE button.” Release the data setting performed at step 1. (Refer to page 5-13) 5-31...
Page 137: Af Illumination Check
DSC-P71/P71M RadarW RadarW RadarW RadarW RadarW 19. AF Illumination Check Check the deviation of optical axis of AF illuminator. Mode CAMERA Subject Flash adjustment box (Note 3) (50 cm or 1 m from the front of lens) Measurement Point Check operation on monitor TV...
Page 138: Lcd System Adjustments
DSC-P71/P71M 1-5. LCD SYSTEM ADJUSTMENTS [Adjusting connector] Most of the measuring points for adjusting the LCD system are Before perform the camera system adjustments, check that the concentrated in CN 903 of the PK-064 board. specified values of “VIDEO SYSTEM ADJUSTMENTS” are sat- Connect the Measuring Instruments via the CPC-9 jig (J-6082- isfied.
Page 139: Lcd Initial Data Input (1)
DSC-P71/P71M 1. LCD Initial Data Input (1) 2. LCD Initial Data Input (2) Mode PLAY Mode PLAY Signal Arbitrary Signal Arbitrary Adjustment Page Adjustment Page Adjustment Address 62, 63, 80 to 8F, A3, A4 Adjustment Address 3A to 3F Adjusting method: Adjusting method: 1) Select page: 0, address: 01, and set data: 01.
Page 140: Backlight Current Adjustment (Pk-064 Board)
DSC-P71/P71M 3. Backlight Current Adjustment (PK-064 Board) 4. VCO Adjustment (PK-064 Board) Adjust electric current value of backlight in two modes. Set the VCO free-run frequency. If deviated, the LCD screen will be blurred. Mode PLAY Mode PLAY Signal Arbitrary...
Page 141: Psig Gray Adjustment (Pk-064 Board)
DSC-P71/P71M 5. PSIG Gray Adjustment (PK-064 Board) 6. D Range Adjustment (PK-064 Board) Set the common electrode drive signal level of LCD to the speci- Set the D Range of the RGB decoder for driving the LCD to the fied value.
Page 142: Black Limit Adjustment (Pk-064 Board)
DSC-P71/P71M 7. Black Limit Adjustment (PK-064 Board) 8. Contrast Adjustment (PK-064 Board) Set the maximum amplitude of the RGB decoder for driving the Set the level of the VIDEO signal for driving the LCD to the speci- LCD to the specified value.
Page 143: Center Voltage Adjustment (Pk-064 Board)
DSC-P71/P71M 9. Center Voltage Adjustment (PK-064 Board) 10. V-COM DC Adjustment (PK-064 Board) Set the center level of VIDEO signal for driving the LCD to the Set the DC bias of the common electrode drive signal of LCD to specified value.
Page 144: White Balance Adjustment (Pk-064 Board)
DSC-P71/P71M 11. White Balance Adjustment (PK-064 Board) Correct the white balance. If deviated, the LCD screen color cannot be reproduced. Mode PLAY Signal Arbitrary Measurement Point Check on the LCD screen Measuring Instrument Adjustment Page Adjustment Address 88, 89 Specified Value...
Page 145: Service Mode
DSC-P71/P71M 5-2. SERVICE MODE • Changing the address The address increases when the FF (M) button is pressed, 2-1. ADJUSTING REMOTE COMMANDER and decreases when the REW (M) button is pressed. There The adjusting remote commander is used for changing the calcu- are altogether 256 addresses, from 00 to FF.
Page 146: Data Process
DSC-P71/P71M 2-2. DATA PROCESS The calculation of the adjusting remote commander display data (hexadecimal notation) are required for obtaining the adjustment data of some adjustment items. In this case, after converting the hexadecimal notation to decimal notation, calculate and convert the result to hexadecimal notation, and use it as the adjustment data.
Page 147: Service Mode
DSC-P71/P71M 2-3. SERVICE MODE 3. Switch Check (1) 1. Setting the Test Mode Page 2 Address 80 Page D Address 21 Function When bit value=1 When bit value=0 Data Function POWER SW (CONTROL Normal SWITCH BLOCK) Forced MOVIE mode power ON...
Page 148: Switch Check (2)
DSC-P71/P71M 4. Switch Check (2) Page 2 Addresses 90, 91, 92, 94 Using method: 1) Select page: 2, addresses: 90, 91, 92 and 94. 2) By discriminating the dispaly data, the pressed key can be discriminated. Data Address 00 to 0C...
Page 149: Repair Parts List
• Items marked “*” are not stocked since they are • DSC-P71M is the same as DSC-P71 (US model) Les composants identifiés par une marque 0 sont critiquens pour la seldom required for routine service. Some delay except packing materials.
Page 150: Cabinet (Rear) Assembly
DSC-P71/P71M 6-1-2. CABINET (REAR) ASSEMBLY ns: not supplied LCD901 BZ901 D901 : BT401 (BATTERY, LITHIUM SECONDARY) Board on the mount position. (See page 4-48.) The components identified by Les composants identifiés par une mark 0 or dotted line with marque 0 sont critiques pour la mark 0 are critical for safety.
Page 151: Lens Block Assembly
DSC-P71/P71M 6-1-3. LENS BLOCK ASSEMBLY J001 BT901 IC351 (Note) (Note) Be sure to read “Precuations for Replacement of CCD Imager” on page 4-8 when changing the CCD imager. The components identified by Les composants identifiés par une mark 0 or dotted line with marque 0 sont critiques pour la mark 0 are critical for safety.
Page 152: Electrical Parts List
µF METAL OXIDE: Metal oxide-film resistor. F: nonflammable • COILS • DSC-P71M is the same as DSC-P71 (US uH: µH model) except packing materials. Therefore, • Abbreviation information about DSC-P71 (US model) in the...
Page 153 DSC-P71/P71M CH-109 JK-231 PK-064 Ref. No. Part No. Description Ref. No. Part No. Description R103 1-218-943-11 RES-CHIP 1/16W C402 1-119-750-11 TANTAL. CHIP 22uF 6.3V R104 1-218-943-11 RES-CHIP 1/16W C403 1-125-777-11 CERAMIC CHIP 0.1uF R105 1-218-943-11 RES-CHIP 1/16W C404 1-125-777-11 CERAMIC CHIP 0.1uF...
Page 154 DSC-P71/P71M PK-064 Ref. No. Part No. Description Ref. No. Part No. Description IC402 6-702-096-01 IC BD4201FV-E2 R424 1-218-949-11 RES-CHIP 1/16W IC801 8-759-660-93 IC RB5P004AM1 R425 1-218-949-11 RES-CHIP 1/16W IC802 8-752-407-33 IC CXD3512R-T4 IC803 8-759-387-31 IC TC75S55F (TE85R) R426 1-218-949-11 RES-CHIP...
Page 155 DSC-P71/P71M PK-064 ST-075 SY-075 Ref. No. Part No. Description Ref. No. Part No. Description R840 1-208-707-11 METAL CHIP 0.5% 1/16W Q502 8-729-055-89 TRANSISTOR MCH3306-TL-E R841 1-218-941-81 RES-CHIP 1/16W Q503 6-550-183-01 TRANSISTOR CPH3209-SONY-TL-E Q504 8-729-053-57 TRANSISTOR RN1902FE (TPLR3) R842 1-218-939-11 METAL CHIP 0.5%...
Page 156 DSC-P71/P71M SY-075 Ref. No. Part No. Description Ref. No. Part No. Description C032 1-115-565-11 CERAMIC CHIP 2.2uF C339 1-127-895-91 TANTAL. CHIP 22uF C034 1-115-566-11 CERAMIC CHIP 4.7uF C340 1-117-919-11 TANTAL. CHIP 10uF 6.3V C035 1-115-566-11 CERAMIC CHIP 4.7uF C341 1-117-919-11 TANTAL. CHIP 10uF 6.3V...
Page 157 DSC-P71/P71M Ver 1.2 2002. 11 SY-075 Ref. No. Part No. Description Ref. No. Part No. Description D206 8-719-077-57 DIODE DF3A8.2C (TPL3) L012 1-469-549-21 INDUCTOR D207 8-719-077-57 DIODE DF3A8.2C (TPL3) L013 1-469-549-21 INDUCTOR D208 8-719-077-57 DIODE DF3A8.2C (TPL3) L014 1-419-628-21 INDUCTOR...
Page 158 DSC-P71/P71M SY-075 Ref. No. Part No. Description Ref. No. Part No. Description Q305 6-550-016-01 TRANSISTOR UMF5NTR R204 1-218-973-11 RES-CHIP 1/16W Q501 8-729-052-59 TRANSISTOR DTA144EHT2L R206 1-218-990-11 SHORT Q701 6-550-016-01 TRANSISTOR UMF5NTR Q703 8-729-427-72 TRANSISTOR XP4501 R215 1-218-961-11 RES-CHIP 4.7K 1/16W...
Page 159 DSC-P71/P71M SY-075 Ref. No. Part No. Description Ref. No. Part No. Description R583 1-218-973-11 RES-CHIP 1/16W 3-074-351-41 MANUAL, INSTRUCTION (DUTCH, ITALIAN) R586 1-218-985-11 RES-CHIP 470K 1/16W (AEP) 3-074-351-51 MANUAL, INSTRUCTION R651 1-218-953-11 RES-CHIP 1/16W (TRADITIONAL CHINESE, SIMPLIFIED CHINESE) R652 1-218-990-11 SHORT...
Page 160 DSC-P71/P71M FOR CAMERA COLOR REPRODUCTION ADJUSTMENT Take a copy of CAMERA COLOR For NTSC mode REPRODUCTION FRAME with a clear sheet for use. DSC-P71/P71M – 201 –...
Page 162 DSC-P71/P71M US Model DSC-P71/P71M Canadian Model SERVICE MANUAL AEP Model UK Model Level 3 E Model Hong Kong Model Ver 1.1 2002. 04 Australian Model Brazilian Model Chinese Model Korea Model Tourist Model Japanese Model DSC-P71 SUPPLEMENT-1 File this supplement with the service manual.
Page 163 DSC-P71/P71M 4-3. PRINTED WIRING BOARDS THIS NOTE IS COMMON FOR WIRING BOARDS (In addition to this, the necessary note is printed in each block) (For printed wiring boards) • : Uses unleaded solder. • Chip parts. Transistor Diode • : Pattern from the side which enables seeing.
Page 164 DSC-P71/P71M CH-109 (CAMERA PROCESS) • For Printed Wiring Board. • :Uses unleaded solder. • CH-109 board is eight-layer print board. However, the pat- terns of layers 2 to 7 have not been included in the diagram. • There are a few cases that the part isn't mounted in this model is printed on this diagram.
Page 165 DSC-P71/P71M SY-075 (CAMERA DSP, VIDEO MEMORY, LENS DRIVE, SH DSP, FLASH MEMORY, CLOCK GENERATOR, DC/DC CONVERTER) • For Printed Wiring Board. • :Uses unleaded solder. • SY-075 board is eight-layer print board. However, the patterns of layers 2 to 7 have not been included in the diagram.
Page 166 DSC-P71/P71M 12, 22 (MS SOCET) – 9 – – 10 – SY-075...
Page 167 DSC-P71/P71M 4-5. PARTS LOCATION no mark : SIDE A * mark : SIDE B CH-109 BOARD SY-75 BOARD * C225 CN707 * L011 * R010 * C103 * C001 * C226 * CN708 * L012 * R011 * C105 * C002...
Page 168 DSC-P71/P71M * R236 R786 * R247 R787 * R256 R788 * R258 R789 * R259 R790 * R260 R304 X781 R306 R309 R310 R311 R312 * R313 * R314 * R315 * R316 * R317 R318 R319 * R320 * R321...
Page 170: Revision History
Reverse 992994913.pdf Revision History S.M. Rev. Ver. Date History Contents issued 2002.03 Official Release — — 2002.04 Supplement-1 • Addition of Brazilian Model. (S1 PV01-066) • Change of the end number of the board. 2002.11 Correction-1 • Correction of repair parts (C1) S.M.

This manual is also suitable for:

Cyber-shot dsc-p71m

Sony Cyber-shot DSC-P71 Service Manual

Quick Links

SPECIFICATIONS

Related Manuals for Sony Cyber-shot DSC-P71

Summary of Contents for Sony Cyber-shot DSC-P71

This manual is also suitable for:

Table of Contents