Basic Operations; Turning On The Power; Selecting The Source To Play - JVC RX-5020VBK Instructions Manual

Basic Operations

Front Panel
Display
STANDBY lamp
FM/AM TUNING FM/AM PRESET FM MODE
UP UP
STANDBY
MEMORY
DOWN DOWN
STANDBY/ON
D I G I T A L
S U R R O U N D
SURROUND ON/OFF
INPUT ANALOG INPUT DIGITAL
INPUT ATT
SURROUND MODE
SPEAKERS ON/OFF
PHONES
PHONES SPEAKERS
jack ON/OFF
STANDBY/ON

Turning On the Power

Press STANDBY/ON (or STANDBY/ON
remote control).
STANDBY
STANDBY/ON
On the front panel
The STANDBY lamp goes off. The name of the current source (or
station frequency) appears on the display.
Current source name appears
SPK
ANALOG
L C R
S.WFR LFE
LS S RS
CH-
Current volume level is shown here
To turn off the power (into standby mode)
Press STANDBY/ON (or
STANDBY/ON AUDIO on the remote
control) again.
The STANDBY lamp on the front panel lights up.
Note:
A small amount of power is consumed in standby mode. To turn the
power off completely, unplug the AC power cord.

Selecting the Source to Play

Press one of the source selecting buttons. The selected source name
appears on the display.
DVD VCR TV SOUND
CD TAPE/CDR FM/AM
SOURCE NAME
On the front panel
8
AUDIO/VIDEO CONTROL RECEIVER
ANALOG SPK TUNED STEREO AUTO MUTING SLEEP
DIGITAL AUTO L C R PRO LOGIC ΙΙ DSP H.PHONE VOLUME
INPUT ATT
LINEAR PCM S.WFR LFE
DIGITAL LS S RS
CH-
DVD VCR TV SOUND
ADJUST SETTING
CD TAPE/CDR FM/AM
CONTROL
DOWN UP
SOURCE NAME
Source
SOURCE
selecting
NAME
buttons
AUDIO on the
STANDBY/ON
AUDIO
From the remote control
VOLUME
STANDBY
STANDBY/ON
TAPE/CDR CD DVD
FM/AM TV SOUND VCR
From the remote control
Remote Control
MASTER VOLUME
Source
selecting
buttons
MASTER
VOLUME
DVD : Select the DVD player.
VCR : Select the VCR.
TV SOUND : Select the TV sound (or the CATV converter).
CD * : Select the CD player.
TAPE/CDR * : Select the cassette deck (or the CD recorder).
FM/AM * : Select an FM or AM broadcast.
• Each time you press the button, the band
alternates between FM and AM.
Notes:
• When connecting a CD recorder (to the TAPE/CDR jacks), change
the source name that appears on the display. See below for details.
• When you have connected some digital source components using
the digital terminals (see page 7), you need to select the digital
input mode (see page 11).
• When you press one of the source selecting buttons on the remote
control marked above with an asterisk ( * ), the receiver
automatically turns on.
Changing the source name
When you connect the CD recorder to the TAPE/
CDR jacks on the rear panel and select the CD
recorder as the source, change the source name
shown on the display.
1
Press TAPE/CDR (SOURCE NAME).
• Make sure "TAPE" appears on the display.
2
Press and hold SOURCE NAME
(TAPE/CDR) until "ASSIGN CDR" appears on the display.
To change the source name from "CDR" to "TAPE," repeat the
same procedure above (in step 1 , make sure "CDR" appears on the
display).
Note:
Without changing the source name, you can still use the connected
component. However, there may be some inconvenience.
– "TAPE" will appear on the display when you select the CD
recorder.
– You cannot use the digital input (see page 11) for the CD recorder.
– You cannot use the COMPU LINK remote control system (see page
24) to operate the CD recorder.
TV CATV
A/V CONTROL
STANDBY/ON
RECEIVER
STANDBY/
TEST CENTER AUDIO
1 2 3
EFFECT REAR L
TV/CATV ON
4 5 6
MENU REAR R
VCR
AUDIO
7/P 8 9
ENTER SUBWOOFER
DVD
10 0 10
RETURN 100
SLEEP
SLEEP
SOUND
PTY–PTY SEARCH–PTY
REW FF
REC PAUSE CD–DISC
TAPE/CDR CD DVD
ANALOG
FM/AM TV SOUND VCR /DIGITAL
FM MODE FM MODE
ON/OFF
TV/VIDEO SURROUND
MUTING MUTING
MODE
VOLUME
VCR CH TV/CATV CH TV VOLUME
+/–
VOLUME
REMOTE CONTROL RM - SRX5020J
Remote
NOT
TAPE/CDR
SOURCE NAME