Panasonic PV-GS19P Service Manual page 57

PV-GS19P / PV-GS31P / PV-GS32P / PV-GS35P / PV-GS19PC / PV-GS31PC / PV-GS34PC / PV-GS35PC
I/O CHART OF IC6001
Pin No. I/O Signal Name Description
(Not used)
1 --- NC
2 I AVCC31 +2.8V
3 --- AVSS Ground
4 I DVCC2 +2.4V
5 --- ENDIAN (Not used)
6 --- BOOT (Not used)
7 O PCTS3 (Not used)
8 O PCTS0 (Not used)
9 --- INTLV (Not used)
10 --- SDI / DINT (Not used)
11 O PCTS2 (Not used)
12 --- SDAO / TPC (Not used)
13 --- BW0 (Not used)
14 --- /DBGE (Not used)
15 --- DCLK (Not used)
16 --- USB INT (Not used)
17 O PCTS1 (Not used)
18 --- SYSRDY (Not used)
19 --- Ground
DVSS
20 --- (Not used)
TEST1
21 --- (Not used)
BUSMD
22 --- (Not used)
/DRESET
(Not used)
23 --- TEST5
24 I RESET Reset : Low
25 --- PLL ON (Not used)
26 I FVCC2 +2.4V
27 --- FVSS Ground
28 --- NMI (Not used)
29 --- BW1 (Not used)
30 I DVCC2 +2.4V
31 I DVCC31 +1.8V
32 --- NC (Not used)
33 O SBA SIF CLK Sub Audio / SIF Serial Clock
34 --- NC (Not used)
35 --- NC (Not used)
36 O SBA CS Sub Audio Chip Select
37 --- NC (Not used)
38 I SBA SIF DTI Sub Audio / SIF Serial Data
39 --- NC (Not used)
40 O SBA SIF DTO Sub Audio / SIF Serial Data
41 --- NC (Not used)
42 I S PLUG S-Video In Defect : Low
43 --- NC (Not used)
44 --- NC (Not used)
45 I FVCC3 +3.4V
46 --- FVSS Ground
47 --- DVSS Ground
48 LCD Reverse : Low
I LCD RVS SW
49 --- (Not used)
NC
50 --- (Not used)
NC
51 LCD Open : Low
I LCD OPEN SW
A/V Input Detect : Low
52 I AV PLUG
USB Input Detect : Low
53 I USB DET
(Not used)
54 --- XRST ARM
55 --- ARB (Not used)
(Not used)
56 --- NC
57 O USB DPBIAS USB Bias Addition
58 O XRST Reset : Low
59 --- NC (Not used)
(Not used)
60 --- NC
61 --- NC (Not used)
62 --- NC (Not used)
63 --- NC (Not used)
64 --- NC (Not used)
65 --- NC (Not used)
66 O PWM BIAS PWM Bias Control
67 I ZENC Zoom Encoder
68 I HOST REQ Request from DMA
69 --- NC (Not used)
70 I DVCC32 +2.8V
71 O HOLE BIAS Hall Bias Control
NOTE: For placing a purchase order of the parts,
be sure to use the part number listed in the parts list.
Do not use the part number on this diagram.
Pin No. I/O Signal Name Description Pin No. I/O
(Not used)
72 --- NC 143 ---
73 O HOST ACK Acknowledge for DMA 144 I
74 --- NC (Not used) 145 O
75 --- NC (Not used) 146 ---
76 O LCD CS LCD Chip Select 147 ---
77 O HOLE GAIN Hall Amp Gain Control 148 ---
78 I FENC Focus Encoder 149 ---
79 O S-PHOTO-SW2 Supply Photo TR Switch 2 150 ---
80 O T-PHOTO-SW1 Takeup Photo TR Switch 1 151 I
81 O MIC CLK MIC Serial Clock 152 I
82 I/O MIC DATA MIC Serial Data 153 ---
83 --- DVSS Ground 154 I/O
84 I REMOCON IR Remote Control Data 155 ---
85 O S-PHOTO-SW1 Supply Photo TR Switch 1 156 I
86 O PS L Power Save : Low 157 I
87 O T-PHOTO-SW2 Takeup Photo TR Switch 2 158 ---
88 --- CAM D3OFF (Not used) 159 I/O
89 --- NC (Not used) 160 ---
90 --- (Not used) 161 ---
NC
91 --- (Not used) 162 I/O
NC
92 --- (Not used) 163 I/O
NC
93 O 164 I/O
LCD EVF SCK LCD / EVF Serial Clock
Serial Clock
94 O ERF CLK 165 I/O
Serial Data 0
95 O ERF DO 166 I/O
Serial Data 1
96 I ERF DI 167 ---
(Not used)
97 --- NC 168 I
98 I LCD EVF DI LCD / EVF Serial Data 169 I/O
(Not used)
99 --- NC 170 ---
100 I DVCC2 +2.4V 171 I/O
101 I DVCC32 +2.8V 172 I/O
102 O LCD EVF DO LCD / EVF Serial Data 173 I/O
103 I PC RST RS-232C Reset 174 I/O
104 --- NC (Not used) 175 I/O
105 I 232C RXD RS-232C Received Data 176 I/O
106 O 232C TXD RS-232C Transmitted Data 177 I
107 --- NC (Not used) 178 ---
108 --- NC (Not used) 179 I/O
109 --- NC (Not used) 180 ---
110 O LIGHT ON Light On : High 181 ---
111 --- NC (Not used) 182 O
112 O MIC ON MIC Power On : Low 183 O
113 --- NC (Not used) 184 O
114 O RTC CS Timer Chip Select 185 O
115 O SNS LED Sensor LED On : High 186 ---
116 --- NC (Not used) 187 I
117 --- DVSS Ground 188 I/O
118 --- OSD SCK (Not used) 189 ---
119 --- (Not used) 190 ---
OSD DO
120 --- (Not used) 191 O
NC
121 O IC701 Reset 192 O
LENS DRV RST
122 O Power On : High 193 O
POWER ON
Lens Drive Test 2
123 I LENS DRV TST2 194 ---
LED Control
124 O LENS LED 195 I
Lens Drive Test 1
125 I LENS DRV TST1 196 I
(Not used)
126 --- RSTPUP 197 ---
127 O EE PROTECT EEPROM Write Protect 198 ---
128 O FLASH WE EEPROM Write Enable 199 ---
129 I DVCC32 +2.8V 200 ---
(Not used)
130 --- EVF ON H 201 ---
(Not used)
131 --- NC 202 ---
132 --- NC (Not used) 203 ---
133 --- NC (Not used) 204 ---
134 O EVF BL EVF Backlight On : High 205 O
135 --- NC (Not used) 206 ---
136 --- NC (Not used) 207 ---
137 --- NC (Not used) 208 ---
138 --- NC (Not used) 209 ---
139 --- NC (Not used) 210 I
140 --- NC (Not used) 211 I
141 --- DVSS Ground 212 I
142 --- NC (Not used) 213 ---
NOTE:
PARTS MARKED "PT" ARE NOT USED.
Signal Name Description Pin No. I/O Signal Name
(Not used)
NC 214 O X2
DVCC33 +1.8V 215 --- NC
LCD ON H LCD Power On : High 216 I CASS DOWN
(Not used)
MODE14 217 O CG RST
(Not used)
NC 218 --- USB2 INT
NC (Not used) 219 --- AFST
LCD BL (Not used) 220 I DUO INT3
NC (Not used) 221 I DUO INT2
S/S SW REC / Pause SW On : Low 222 I DUO INT1
PHOTO SW Photo SW On : Low 223 --- DVSS
TEST4 (Not used) 224 I HPDET L
ADM[2] Address / Data 2 225 I TIMER INT
STNDBY SW (Not used) 226 I CAM VD
CARD DET SD Card Detect 227 I DUO INT0
SD PROTECT SD Card Protect 228 --- EXT H
TEST3 (Not used) 229 --- NC
ADM[0] Address / Data 0 230 --- NC
DVSS Ground 231 I EJECT SW
(Not used) 232 ---
CAM TEST NC
Address / Data 1 233 O
ADM[1] ACCESS LED
Address / Data 6 234 ---
ADM[6] OSD CS
Address / Data 3 235 I
ADM[3] POWER SW
Address / Data 5
ADM[5] 236 --- OSD RST
Address / Data 4
ADM[4] 237 --- NC
FVSS Ground 238 --- NC
FVCC2 +2.4V 239 O EEP CS
ADM[9] Address / Data 9 240 I DVCC34
(Not used)
TEST0 241 O FLASH CE
ADM[8] Address / Data 8 242 --- NC
ADM[7] Address / Data 7 243 --- NC
ADM[10] Address / Data 10 244 --- NC
ADM[13] Address / Data 13 245 I LIGHT SW
ADM[11] Address / Data 11 246 O STNDBY LED
ADM[12] Address / Data 12 247 O POWER LED
DVCC33 +1.8V 248 --- NC
NC (Not used) 249 O CROSS LED
ADM[15] Address / Data 15 250 --- DVSS
NC (Not used) 251 --- NC
DVSS Ground 252 I DVCC2
XDUO CS IC3001 Chip Select 253 --- AVSS
XWEH Write Enable : Low 254 I LOAD LOCK DET
XREADY Ready : Low 255 I AVCC32
XRE Read Enable : Low 256 I T PHOTO
FVSS Ground 257 I BATT D
FVCC2 +2.4V 258 I S PHOTO
ADM[14] Address / Data 14 259 I MIC AD1
USB CS (Not used) 260 I MIC AD2
(Not used) 261 I
NC MIC AD3
CCD Power On : High 262 ---
CCD ON H AVSS
Latch Enable 263 I
ALE ADKEY 1
White Enable : Low 264 I
XWEL ADKEY 4
(Not used)
TEST2 265 I SENSE TMP LENS
+1.8V
DVCC33 266 I ZOOM
DVCC2 +2.4V 267 I REGD3V DET
(Not used)
ICS3 268 I BATT REF
(Not used)
ICS2 269 I ADKEY 3
(Not used)
NC 270 I BATTERY
(Not used)
XT1 271 I Y LEVEL ADJ
(Not used)
CVCCH 272 I ADKEY 2
(Not used)
CAP1 273 I EXT MIC
(Not used)
CAP2 274 I IROUT
(Not used)
XT2 275 I FNO
TDO Test Data 276 I DEW
TDI Test Point 277 I HANSEIHW DET
TMS Test Point 278 I UNI REMO
TRST (Not used) 279 I JACK DET
TCK Test Point 280 --- VREFL
DVCC34 +2.8V 281 I VREFH
CVCC2 +2.4V 282 --- NO PIN
X1 13.5MHz Clock 283 --- NO PIN
CVSS Ground 284 --- NO PIN
PV-GS19P/PV-GS19PC/PV-GS31P/PV-GS31PC/PV-GS32P/PV-GS34PC/PV-GS35P/PV-GS35PC
60
NOTE:
FOR SCHEMATIC DIAGRAM AND CIRCUIT BOARD LAYOUT NOTES,
REFER TO BEGINNING OF SCHEMATIC SECTION.
I/O CHART OF IC6002
Description Pin No. I/O Signal Name
13.5MHz Clock 1 I CS EEPROM chip select
(Not used)
2 I SCK EEPROM serial clock
Cassette Down : Low
3 I SI EEPROM serial data 0
IC302 Reset
4 O SO EEPROM serial data 1
USB Interrupt
5 - GND Ground
(Not used)
6 I RESET EPROM write protect
IC3001 Interrupt 3
7 - R/B (Not used)
IC3001 Interrupt 2
8 I VDD +3.0V
IC3001 Interrupt 1
Ground
Headphone Detect : Low
Timer Interrupt
Camera V-sync
IC3001 Interrupt 0
(Not used)
(Not used)
(Not used)
Eject SW On : Low
(Not used)
Access LED On : Low
(Not used)
Power SW On : Low
(Not used)
(Not used)
(Not used)
IC 6002 Chip Select
+2.8V
IC 6009 Chip Select
(Not used)
(Not used)
(Not used)
Light SW On : Low
Standby LED On : Low
Power LED On : Low
(Not used)
CROSS LED ON : High
Ground
(Not used)
+2.4V
Ground
Loading Lock Detect
+2.8V
Takeup Photo TR On : Low
Battery Detect
Supply Photo TR On : Low
MIC On : High
MIC Serial Clock
MIC Serial Data
Ground
ANALOG KEY INPUT
ANALOG KEY INPUT
Lens Temperature Sensor
ANALOG KEY INPUT
+3V Detect
V-Ref for Battery
ANALOG KEY INPUT
Battery Voltage Detect
Y LEVEL ADJUST
ANALOG KEY INPUT
EXT MIC In Detect : Low
IR Detect
F Number
Dew Sensor
(Not used)
Wired Remote Control Data
JACK Detect
V-Ref Low (0V)
V-Ref High (+2.8V)
(Not used)
(Not used)
(Not used)
COMPARISON CHART
OF MODELS & MARKS
MODEL MARK
PV-GS19P-S A
PV-GS19PC-S B
PV-GS31P-S C
PV-GS31PC-S D
PV-GS32P-S E
Description - - - - - F
PV-GS34PC-S G
PV-GS35P-S H
PV-GS35PC-S I
Not Used PT
I/O CHART OF IC6001
LSJB8295
I/O CHART OF IC6002