Related Manuals for Strong SM-RAZOR-F-M
Summary of Contents for Strong SM-RAZOR-F-M
- Page 1 SM-RAZOR-F-M SM-RAZOR-F-L • SM-RAZOR-F-XL SM-RAZOR-F-M SM-RAZOR-F-L Strong™ Low Profile Fixed Mount for Ultra-Thin Flat-Panel TVs SM-RAZOR-F-XL Instruction Manual INSTRUCTION MANUAL...
-
Page 2: Specifications
WARNINGS: • Installation of this product should be done by a qualified professional. • Do not begin installation before reviewing and understanding these instructions. • Ensure the mounting wall used can safely support 4 times the combined weight of the mount and chosen display. • Under no circumstances should this product be mounted to metal studs. • The manufacturer does not accept responsibility for incorrect installation. CAUTION: This wall mount is intended for use only with the maximum weight of 100 lbs for models SM-RAZOR-F-M & SM-RAZOR-F-L; 150 lbs for model SM- RAZOR-F-XL. Use with heavier than the maximum weight indicated may result in instability causing possible injury. SPECIFICATIONS TOOLS REQUIRED Maximum Load: • Power Drill SM-RAZOR-F-M 100 lbs. • 5/6” and 3/16” Drill Bit SM-RAZOR-F-L 100 lbs. -
Page 3: Package Contents
L & XL Models Only (O) M8 x 30mm (P) M8 x 40mm (Q) 17.8 x 6.5 x 1.5mm Philips Head Screw (x4) Philips Head Screw (x4) M6 Metal Washer (x8) M Model Only L & XL Models Only (R) 20.5 x 8.5 x 2mm (S) OD13 x ID6 x 12mm (T) OD17 x ID8.5 x 12mm M8 Metal Washer (x8) Black Nylon Spacer (x4) Black Nylon Spacer (x4) L & XL Models Only Wall Plate (U) M10 x 15mm Philips Head Screw (x4) XL Model Only Arms pg.3 © 2012 STRONG... -
Page 4: Installation
SM-RAZOR-F Installation and Users Manual INSTALLATION Step 1: Mounting the Wall Bracket Assembly Figure 1 For Mounting on a Stud Wall A. Pre-drill holes into two wood studs using a 3/16” drill bit. Be sure to drill into the center of the studs at least 2-1/2” deep. The use of a stud finder is highly recommended. B. Insert the Lag screws (A) into holes through the Wall Plate and tighten. (Figure 1). WARNING: Tighten bolts so that wall plate is firmly attached, but do not over tighten. Over tightening can damage the bolts, greatly reducing their holding strength. For Mounting on a Concrete Wall WARNING: When installing wall bracket on cinder block: • Verify first that you have a minimum of 1-3/8” of concrete thickness to be used for the concrete anchors. - Page 5 Drill holes and Wall plaster/ plas ter/ insert anchors. drywall drywall Place wall arm Wall Arm assembly plate concrete concrete over anchor and Figure 2 secure with Flange Bolt lag screw. Tighten all lag screws. Figure 4 pg.5 © 2012 STRONG...
- Page 6 SM-RAZOR-F Installation and Users Manual Step 2: Mount Arms to television A. Determine the diameter of the screw Figure 4 (parts C through P & U) your TV requires by carefully trying to hand-thread one into the threaded insert on the rear of the TV. If there is any resistance, stop immediately. B. Spacers are commonly needed on televisions with curved backs or recessed screw inserts. The screw will thread through the appropriate washer (Q or R), any spacer needed (S or T) and the arms into the TV. C. Ensure the arms are installed flat side to television and are square to each other after all screws have been installed (Figure 4). D. Slide the clip up to lengthen and down to shorten the release string. Adjust the height of the Arm release to be above the bottom of the TV. (Figure 5). Figure 5 Lengthen Shorten Top of Arm pg.6...
- Page 7 WIRE MANAGEMENT KICKSTANDS The SM-RAZOR-F mounts are equipped with a Kickstand that provides space between the TV and the wall for connecting or disconnecting cabling. Note: These Kickstands are provided for servicing only, it is recommended that they are collapsed and the arms locked during normal placement. Figure 8 A. Pull down on the rings at the bottom of the arms to release them from the wall bracket. B. Pull the kickstands out on each arm so that they rest on the wall. (Figure 8). C. When finished, collapse the kickstands to allow the arms to lock onto the wall bracket. pg.7 © 2012 STRONG...
-
Page 8: Lifetime Limited Warranty
LIFETIME LIMITED WARRANTY Strong™ Mounts have a Lifetime Limited Warranty. This warranty includes parts and labor Lifetime repairs on all components found to be defective in material or workmanship under normal conditions of use. This warranty shall not apply to products which have been abused, modified or disassembled. Products to be repaired under this warranty must be returned to SnapAV or a designated service center with prior notification and an assigned return authorization number (RA). CONTACTING TECHNICAL SUPPORT PHONE: (866) 838-5052 EMAIL: TECHSUPPORT@SNAPAV.COM © 2012 STRONG™ 121017-1700...