Main Unit Bottom/Side/Top; Installation And Connection System Diagram; Installing The Camera - JVC Dome Camera TK-C205VP Instructions Manual

Names and Operations of Parts

Main unit bottom/side/top

bottom
1 Safety cable installation screw
Install the safety cable using this screw.
(Safety cable not included.)
CAUTION
To avoid unforeseen accidents, attach a
safety cable. Otherwise, there is nothing
to prevent the camera from falling should
it come loose.
2 Mounting holes (for mounting to the
electrical box)
When using a 4 inch square electrical
box, the 2 holes are used to fix the box
in place.
CAUTION
Use screw size suitable for the mounting
holes (ø5mm ( 3 / ")).
16
3 Mounting holes (for mounting to the
ceiling)
These holes are used to mount the
camera body to the ceiling.
E-8
side top
CAUTION
Use screw size suitable for the mounting
3
holes (ø5mm ( / ")).
16
Conduit hole
4
Hole for installation to conduit hole pipe
and wiring.
5 Conduit plug & hole (side)
When the unit cannot be installed to the
ceiling, the pipe is mounted to this hole
for wiring.
6 Tamper-resistant screws
Tamper-resistant screws for fixing the
dome cover to the base.
Use the provided wrench to install/
remove the Tamper-resistant screws.
Installation and connection
System diagram
Camera 1
Video signal
Power
Camera 2
Video signal
Power
Camera 3 Video signal
Power
Camera 4 Video signal
Power
Power Unit
DC 12 V or AC 24 V
TO CAMERA TO CAMERA
RX RX+ RX RX- TX+ TX-
COM COM 1 2 3 4 5 6 7 8
POWER
OFF
ON
1 2
AC INPUT
1 2 3 4 5 6 7 8
1 2
ON ON
Switcher, etc.
• Turn OFF the power supply to all equipment to be used before making connections.
• Read the Instruction Manual for each piece of equipment to be used before making
connections.

Installing the camera

Install the camera to the ceiling by following the procedure below
• Mounting the base ................................................................................................. 10-11
• Connect the Cables to the Base ................................................................................ 12
• Mount the Camera unit to the Base ........................................................................... 13
• Fill using sealing agent
• Insert the included Silica gel
• Before Adjusting the Camera ..................................................................................... 14
• Adjusting the Lens and Camera Angle ...................................................................... 14
• Attach the Dome cover ............................................................................................... 15
When Installing the Camera Using the Conduit Hole (side) ........................................ 16
When Installing the Camera Using the Electrical Box .................................................. 17
When installing the camera to a ceiling without piping ................................................ 18
MEMO
Power supply necessary for one TK-C205VP
DC 12V : 300mA
AC 24V : 280mA
• When the voltage drops due to fluctua-
tions in voltage or compatibility with the
power supply cable, the current increases
by 30% for each TK-C205VP.
HDR, VTR, etc.
SR-L910E
REC STOP/EJECT CHECK REC VIDEO CASSETTE RECORDER OPERATE
PAUSE/ OPE. LOCK
REVERSE STILL PLAY COUNT/ CLOCK MENU SHIFT/TRACKING RESET /CANCEL
REW FF TIME TIMER SET/V.LOCK AL/PL
MODE REC RESET
VIDEO IN
VIDEO
INPUT
DATA I / O DATA I / O
UNIT UNIT CAMERA CAMERA SERIAL-1 SERIAL-1 SERIAL-2 SERIAL-2
COM 9/1 COM 9/1 10/2 11/3 11/3 12/4 12/4 13/5 13/5 14/6 14/6 15/7 15/7 16/8 16/8 COM COM AUTO AUTO ALARM ALARM COM COM SW SW COM
MONITOR
OUTPUT 2
VIDEO INPUT VIDEO INPUT
3 4 5 6 7
8
MONITOR MONITOR MONITOR
OUTPUT OUTPUT OUTPUT
1 2
3 4 5 6 7 8
VIDEO OUTPUT VIDEO OUTPUT
MONITOR
OUTPUT 1
MONITOR
MONITOR
E-9