Page 1 DCR-TRV120 Australian Model Chinese Model DCR-TRV120E B700 MECHANISM Tourist Model Photo: DCR-TRV120 DCR-TRV120/TRV120E NTSC MODEL : DCR-TRV120/TRV120P For MECHANISM ADJUSTMENT, refer to PAL MODEL : DCR-TRV120E/TRV125E/TR8000E/TR8100E the “8mm Video MECHANICAL ADJUSTMENT MANUAL ” (9-973-801-11). SPECIFICATIONS – Continued on next page –...
Page 2 DE FONCTIONNEMENT. NE REMPLACER CES COM- SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB- POSANTS QUE PAR DES PIÈCES SONY DONT LES LISHED BY SONY. NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
Page 3 Supplied accessories Table for differences of function Model DCR-TRV120 DCR-TRV120P DCR-TRV120E DCR-TRV125E DCR-TR8000E DCR-TR8100E US, CND, E, HK, AEP, UK, EE, E, AUS, HK, AEP, UK, EE, Destination E, AR KR, BR, JE NE, RU NE, RU CN, JE Color system...
Page 4: Table Of Contents
TABLE OF CONTENTS Section Title Page Section Title Page SERVICE NOTE 2-7. EVF Block ..............2-4 ..............7 2-8. EVF Assembly ............... 2-5 2-9. VF-129 Board , CRT Assembly ........2-5 Power Supply During Repairs ........7 2-10. Battery Panel Assembly ..........2-6 To Take Out a Cassette 2-11.
Page 5 Overall Level Characteristics Check ......5-53 1-5. LCD System Adjustments Overall Distortion Check .......... 5-53 (DCR-TRV120/TRV120E/TRV120P/TRV125E) ..5-28 Overall Noise Level Check ........5-54 LCD Initial Data Input (1) ......... 5-28 Overall Separation Check ........5-54 LCD Initial Data Input (2) ......... 5-29 5-4.
Page 6 Section Title Page 4-3. Service Mode ............5-57 Setting the Test Mode ..........5-57 Emergence Memory Address ........5-57 2-1. C Page Emergence Memory Address ..... 5-57 2-2. F Page Emergence Memory Address ...... 5-58 2-3. EMG Code (Emergency Code) ........ 5-58 2-4.
Page 7: Service Note
SERVICE NOTE POWER SUPPLY DURING REPAIRS Battery switch In this unit, about 10 seconds after power is supplied (8.4 V) to the battery terminal using the service power cord (J-6082-223-A), the power is shut off so that the unit cannot operate. This following two methods are available to prevent this.
Page 8: Note For Repair
NOTE FOR REPAIR When remove a connector, don’t pull at wire of connector. Be in danger of the snapping of a wire. Make sure that the flat cable and flexible board are not cracked of bent at the terminal. Do not insert the cable insufficiently nor crookedly. When installing a connector, don’t press down at wire of connector.
Page 9: Self-Diagnosis Function
SELF-DIAGNOSIS FUNCTION Self-diagnosis Display Self-diagnosis Function When problems occur while the unit is operating, the counter of When problems occur while the unit is operating, the self-diagno- sis function starts working, and displays on the viewfinder or Dis- the viewfinder or Display window shows a 4-digit display consist- play window what to do.
Page 10: Self-Diagnosis Code Table
Self-diagnosis Code Table Self-diagnosis Code Block Detailed Symptom/State Correction Function Code Condensation. Remove the cassette, and insert it again after one hour. Video head is dirty. Clean with the optional cleaning cassette. Non-standard battery is used. Use the InfoLITHIUM battery. LOAD direction.
Page 11 Self-diagnosis Code Block Detailed Symptom/State Correction Function Code Inspect the lens block focus reset sensor (Pin 9 of CN1551 of VC-235 board) when focusing is performed when the control dial Difficult to adjust focus is rotated in the focus manual mode and the focus motor drive circuit (Cannot initialize focus.) (IC1553 of VC-235 board) when the focusing is not performed.
Page 12: General
DCR-TRV120/TRV120E/TRV120P/TRV125E/ TR8000E/TR8100E SECTION 1 GENERAL This section is extracted from DCR-TRV120E/ TRV125E/TRV320E instruction manual.
Page 21 1-10...
Page 22 1-11...
Page 23 1-12...
Page 24 1-13...
Page 25 1-14...
Page 26 1-15...
Page 27 1-16...
Page 28 1-17...
Page 29 1-18...
Page 30 1-19...
Page 31 1-20...
Page 32 1-21...
Page 33 1-22...
Page 34 1-23...
Page 35 1-24...
Page 36 1-25...
Page 37 1-26...
Page 38 1-27 E 1-27...
Page 39 DCR-TRV120/TRV120E/TRV120P/TRV125E/ SECTION 2 TR8000E/TR8100E DISASSEMBLY • This set can be disassembled in the order shown below. Note: TRV model : DCR-TRV120/TRV120E/TRV120P/TRV125E TR model : DCR-TR8000E/TR8100E DCR-TRV120/TRV120E/TRV120P/TRV125E/TR8000E/TR8100E TRV model 2-1. LCD ASSEMBLY, 2-2. FRONT PANEL ASSEMBLY PD-117 BOARD (page 2-3) (page 2-2) 2-3.
Page 40: Lcd Assembly, Pd-117 Board (Trv Model)
Note: Follow the disassembly procedure in the numerical order given. 2-1. LCD ASSEMBLY, PD-117 BOARD (TRV model) ql Indication (LCD) block assembly qk Claw qj Claw qg Flexible board (CN5705) 9 Two screws 6 P cabinet (C) qh Claw qf PD-117 board 2 Two screws (P2 ×...
Page 41: Front Panel Assembly
2-2. FRONT PANEL ASSEMBLY 2-3. CABINET (L) ASSEMBLY, CASSETTE LID ASSEMBLY 1 Two screws 2 Open the control switch block. 5 Cassette lid assembly (2 × 4) 1 Screw (2 × 4) 6 Two screws (2 × 4) 4 Claw 2 Jack cover qa Flexible board (CN253)
Page 42: Cabinet (R) Assembly
2-4. CABINET (R) ASSEMBLY 2-6. CF-71 BOARD (TR model) 2 Two screws 1 Screw (2 × 4) (2 × 4) 5 Flat cable 6 CF-71 board 2 Lithium battery (CN1105) retainer 4 Two screws 5 Rotary switch 1 Two screws 8 Two screws 3 Three screws 9 Indication (LCD)
Page 43: Evf Assembly
2-8. EVF ASSEMBLY 2-9. VF-129 BOARD, CRT ASSEMBLY 3 Turn the finder assembly in the direction of arrow A and 1 F lock screw pull it out. 7 EVF assembly 6 Two screws 2 Release knob. 4 Two screws 6 EVF cabinet (upper) assembly 5 Claw 7 CRT assembly...
Page 44: Battery Panel Assembly
2-10. BATTERY PANEL ASSEMBLY 2-12. LENS BLOCK 1 Two flexible baords (CN1501, 1551) 3 Screw (2 × 4) 4 Battery panel assembly 8 Flexible board (external connector) 3 Screw (2 × 3) 5 Claw 4 Screw (2 × 3) 7 Lens block 2 Screw 2 Screw 1 Connector...
Page 45: Fu-138/143 Board
2-14. FU-138/143 BOARD 2-15. VC-235 BOARD 4 Flexible board 1 Flexible board (CN235) (CN1107) 1 Two screws (2 × 3) 4 Two flexible boards (CN4403, 4404) 2 Connector (CN254) 5 Screw 3 FU-138 board (TRV model) 2 Flexible board (2 × 3) FU-143 board (TR model) (CN1103) 6 VC-235 board...
Page 46: Circuit Boards Location
2-16. CIRCUIT BOARDS LOCATION – TRV model – VC-235 CAMERA PROCESSOR, Y/C PROCESSOR, LENS MOTOR DRIVE, VIDEO/AUDIO IN/OUT, BASE BAND INPUT, VIDEO/AUDIO DSP, DV INTERFACE, OSD, A/D CONVERTER, REC/PB AMP, Hi8/Std8 PB AMP, HI/MECHANISM/CAMERA CONTROL, SERVO, D/A CONVERTER, DC/DC CONVERTER SE-104 STEDY SHOT, AV IN/OUT...
Page 47: Flexible Boards Location
2-17. FLEXIBLE BOARDS LOCATION CONTROL SWITCH BLOCK (SS-10000) FFC-289 FP-157 FP-161 FP-156 PANEL REVERSE SWITCH BLOCK (from LENS BLOCK) (PR-10000) (TRV model) CONTROL SWITCH BLOCK (MF-10000) FP-160 CONTROL SWITCH BLOCK (FK-10000) FFC-257 (from S/T REEL SENSOR) (from CAPSTAN MOTOR) (from DRUM MOTOR) (from VIDEO HEAD) FP-159 from LOADING MOTOR,...
Page 48: Block Diagrams
(SEE PAGE 4-24) MECHA HD S-C I/O XCS ALIGN MECHA VD 960H model PB C RF • 720H model : DCR-TRV120/TRV120P 148 – 153 • • HI SI, HI SO, XHI SCK • 960H model : DCR-TRV120E/TRV125E/TR8000E/TR8100E SPCK XCS TAKO...
Page 49: Overall Block Diagram 2
TRV model : DCR-TRV120/TRV120E/TRV120P/TRV125E LCK0 TR model : DCR-TR8000E/TR8100E INTERFACE VTR REC model : DCR-TRV120/TRV120E : E, HK, AUS, CN, JE/TRV120P RCK0 PLAYER model : DCR-TRV120E : AEP, UK, EE, NE, RUS/TRV125E /TR8000E/TR8100E TYPE S model : DCR-TRV120/TRV120E : AEP, EE, NE, RU, UK...
Page 50: Overall Block Diagram 3
(SEE PAGE 4-40) VC-235 BOARD (3/3) TR model : DCR-TR8000E/TR8100E IC4401 CN4402 VTR REC model : DCR-TRV120/TRV120E : E, HK, AUS, CN, JE/TRV120P OVERALL (2/3) DRUM FG DRUM FG DRUM FG SENS PLAYER model : DCR-TRV120E : AEP, UK, EE, NE, RUS/TRV125E/TR8000E/TR8100E...
Page 51: Power Block Diagram 1
CN1109 TRV model 720H model : DCR-TRV120/TRV120P TRV model : DCR-TRV120/TRV120E/TRV120P/TRV125E VTR REC model : DCR-TRV120/TRV120E : E, HK, AUS, CN, JE/TRV120P 960H model : DCR-TRV120E/TRV125E/TR8000E/TR8100E TR model : DCR-TR8000E/TR8100E PLAYER model : DCR-TRV120E : AEP, UK, EE, NE, RUS/TRV125E/TR8000E/TR8100E...
Page 52: Power Block Diagram 2
DCR-TRV120/TRV120E/TRV120P/TRV125E/ TR8000E/TR8100E 3-5. POWER BLOCK DIAGRAM 2 FP-156 FLEXIBLE VC-235 BOARD (2/2) MI-37 BOARD (SEE PAGE 4-55) IC3901 IC3900 CN1111 CN5804 D3904 F3900 REMOTE VTR UNREG LASER LINK COMMANDER TRANSMITTER RECEIVER (SEE PAGE 4-57) IC5801 (SEE PAGE 4-58) AU 2.8V...
Page 53: Power Block Diagram 3
(SEE PAGE 4-82) BATT LI 3V BH001 LITHIUM BATTERY TYPE C model : DCR-TRV120E : AUS, CN, E, HK, JE TYPE S model : DCR-TRV120/TRV120E : AEP, EE, NE, RU, UK/TRV120P/TRV125E VC-235 BOARD (CN1105) (SEE PAGE 3-8) CAMERA D 2.8V...
Page 54: Frame Schematic Diagrams
DCR-TRV120/TRV120E/TRV120P/TRV125E/ SECTION 4 TR8000E/TR8100E PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS THIS NOTE IS COMMON FOR WIRING BOARDS AND SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block) (For printed wiring boards) (Measuring conditions voltage and waveform) •...
Page 55 SE-104 BOARD TRV120P/TRV125E TALLY_LED SE-113 BOARD VC_SO :DCR-TR8000E/TR8100E XVC_SCK 720H MODEL:DCR-TRV120/TRV120P CN5804 CN1111 KEY_AD2 960H MODEL:DCR-TRV120E/TRV125E/TR8000E/TR8100E IR_FSC IR_FSC KEY_AD3 TRV MODEL:DCR-TRV120/TRV120E/TRV120P/TRV125E VTR REC MODEL:DCR-TRV120/TRV120E:E,HK,AUS,CN,JE/TRV120P REG_GND REG_GND KEY_AD4 PLAYER MODEL:DCR-TRV120E:AEP,UK,EE,NE,RU/TRV125E/TR8000E/TR8100E SIRCS_PWM SIRCS_PWM KEY_AD5 IR_ON IR_ON KEY_AD6 IR_VIDEO IR_VIDEO EVF_B REG_GND REG_GND...
Page 56 LCD904 LCD BLOCK (CHARACTER DISPLAY) Handycam8 01:23:45 FP-94 FLEXIBLE LED904 BACK LIGHT TRV MODEL:DCR-TRV120/TRV120E/TRV120P/TRV125E TR MODEL:DCR-TR8000E/TR8100E TYPE C MODEL:DCR-TRV120E:E,HK,AUS,CN,JE TYPE S 61k/123k MODEL:DCR-TRV120/TRV120E:AEP,UK,EE,NE,RU/TRV120P/TRV125E S004 S001 SEL/PUSH EXEC DIGITAL EFFECT T901 CONTROL SWITCH V901 CRT ASSY CN002 4P :TRV MODEL S002...
Page 57 TR8000E/TR8100E 4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS CD-242 (CCD IMAGER) PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM – Ref. No.: CD-242 board; 20,000 series – – DCR-TRV120/TRV120P – • For Printed Wiring Board. CD-242 BOARD (DCR-TRV120/TRV120P) • There are few cases that the part isn't mounted in this model is printed on this diagram.
Page 58: Cd-244/269 Printed Wiring Board And Schematic Diagram
DCR-TRV120/TRV120E/TRV120P/TRV125E/ TR8000E/TR8100E CD-244/269 (CCD IMAGER) PRINTED WIRING BOARD AND SHEMATIC DIAGRAM • See page 4-87 for waveforms. – Ref. No.: CD-244/269 board; 20,000 series – – DCR-TRV120E/TRV125E/TR8000E/TR8100E – CD-244 BOARD (DCR-TRV120E/TRV125E) • For Printed Wiring Board. • There are few cases that the part isn't mounted in this model CD-269 BOARD is printed on this diagram.
Page 59: Printed Wiring Board
DCR-TRV120/TRV120E/TRV120P/TRV125E/ TR8000E/TR8100E VC-235 (CAMERA PROCESSOR, Y/C PROCESSOR, LENS MOTOR DRIVE, VIDEO/AUDIO IN/OUT, BASE BAND INPUT, VIDEO /AUDIO DSP, DV INTERFACE, OSD, A/D CONVERTER, REC/PB AMP, Hi8/Std8 PB AMP, HI/MECHANISM/CAMERA CONTROL, SERVO, D/A CONVERTER, DC/DC CONVERTER) PRINTED WIRING BOARD – Ref. No.: VC-235 board; 10,000 series –...
Page 60 DCR-TRV120/TRV120E/TRV120P/TRV125E/ TR8000E/TR8100E VC-235 BOARD (SIDE B) Part No. 1-676-764- 12 (22, 32) Location: A – 4, 5 • Refer to the printed wiring board for suffix number 11 (21, 31) for the parts not be shown here. 4-14 CAMERA PROCESSOR, Y/C PROCESSOR, LENS MOTOR DRIVE, VIDEO/AUDIO IN/OUT, BASE BAND INPUT,...
Page 61: Camera Processor) Schematic Diagram
VC-235 BOARD (4/16) C1525 25 26 27 28 29 30 31 32 33 34 35 36 C1520 0.001u SIGNAL PATH Hi8/Std8 C1519 VIDEO SIGNAL 0.22u CHROMA Y/CHROMA 720H MODEL:DCR-TRV120/TRV120P C1513 C1516 C1514 0.47u C1518 960H MODEL:DCR-TRV120E/TRV125E/TR8000E/TR8100E C1517 120p C1514 C1515 :720H MODEL 0.22u...
Page 62: Y/C Processor) Schematic Diagram
DCR-TRV120/TRV120E/TRV120P/TRV125E/ TR8000E/TR8100E VC-235 (Y/C PROCESSOR) SCHEMATIC DIAGRAM • See page 4-11 for VC-235 printed wiring board. • See page 4-87 for waveforms. VC-235 BOARD (2/16) Y/C PROCESSOR (KINUTA BLOCK) -REF.NO.:10,000 SERIES- XX MARK:NO MOUNT NO MARK:REC/PB MODE C2240 R:REC MODE...
Page 63: Lens Motor Drive) Schematic Diagram
DCR-TRV120/TRV120E/TRV120P/TRV125E/ TR8000E/TR8100E VC-235 (LENS MOTOR DRIVE) SCHEMATIC DIAGRAM • See page 4-11 for VC-235 printed wiring board. VC-235 BOARD (3/16) LENS_FILTER_ON_SW LENS MOTOR DRIVE (LD BLOCK) VC-235 BOARD (12/16) -REF.NO.:10,000 SERIES- XX MARK:NO MOUNT HALL_AD R1567 2200 NO MARK:REC/PB MODE...
Page 64: Video In/Out) Schematic Diagram
DCR-TRV120/TRV120E/TRV120P/TRV125E/ TR8000E/TR8100E VC-235 (VIDEO IN/OUT) SCHEMATIC DIAGRAM • See page 4-11 for VC-235 printed wiring board. • See page 4-88 for waveforms. VC-235 BOARD (4/16) VIDEO IN/OUT (TAKO BLOCK) -REF.NO.:10,000 SERIES- XX MARK:NO MOUNT NO MARK:REC/PB MODE A_4.75V R:REC MODE P:Digital8 PB MODE D_2.8V...
Page 65: Base Band Input
DCR-TRV120/TRV120E/TRV120P/TRV125E/ TR8000E/TR8100E VC-235 (BASE BAND INPUT) SCHEMATIC DIAGRAM • See page 4-11 for VC-235 printed wiring board. SIGNAL PATH VC-235 BOARD (5/16) VIDEO SIGNAL BASE BAND INPUT (ALIGN BLOCK) CHROMA -REF.NO.:10,000 SERIES- XX MARK:NO MOUNT NO MARK:REC/PB MODE R:REC MODE...
Page 66: Video/Audio Dsp, D/A Converter) Schematic Diagram
DCR-TRV120/TRV120E/TRV120P/TRV125E/ TR8000E/TR8100E VC-235 (VIDEO/AUDIO DSP, D/A CONVERTER) SCHEMATIC DIAGRAM • See page 4-11 for VC-235 printed wiring board. • See page 4-87, 88 for waveforms. VC-235 BOARD (7/16) VC-235 BOARD (6/16) VC-235 BOARD (7/16) VIDEO/AUDIO DSP,D/A CONVERTER (JC1 BLOCK) -REF.NO.:10,000 SERIES-...
Page 67: Dv Interface, Osd) Schematic Diagram
VBLA CMDCT COL2 EVER_3.0V COL1 XPCL XSYS_RST SIGNAL PATH COL0 DATA OSD_SO VC-235 BOARD(10/16) OSDVD VIDEO SIGNAL XVSYNC XCS_OSD AUDIO OSDHD XHSYNC XCLK XOSD_SCK SIGNAL CHROMA Y/CHROMA IC3302 MB90099PFV-G-102-BND-ER TRV MODEL:DCR-TRV120/TRV120E/TRV120P/TRV125E IC3302 45-1 DV INTERFACE, OSD VC-235 (7/16) 4-27 4-28...
Page 68: A/D Converter, Rec/Pb Amp) Schematic Diagram
DCR-TRV120/TRV120E/TRV120P/TRV125E/ TR8000E/TR8100E VC-235 (A/D CONVERTER, REC/PB AMP) SCHEMATIC DIAGRAM • See page 4-11 for VC-235 printed wiring board. • See page 4-88 for waveforms. VC-235 BOARD (8/16) A/D CONVERTER,REC/PB AMP (RFD BLOCK) -REF.NO.:10,000 SERIES- XX MARK:NO MOUNT NO MARK:REC/PB MODE...
Page 69: Hi8/Std8 Pb Amp) Schematic Diagram
DCR-TRV120/TRV120E/TRV120P/TRV125E/ TR8000E/TR8100E VC-235 (Hi8/Std8 PB AMP) SCHEMATIC DIAGRAM • See page 4-11 for VC-235 printed wiring board. • See page 4-88 for waveforms. VC-235 BOARD (9/16) RP_4.75V Hi8/Std8 PB AMP (RF8 BLOCK) VC-235 BOARD (16/16) A_2.8V -REF.NO.:10,000 SERIES- REG_GND Hi8/Std8...
Page 70: Hi Control) Schematic Diagram
VC-235 BOARD (10/16) XX MARK:NO MOUNT HI CONTROL(HI BLOCK) NO MARK:REC/PB MODE R:REC MODE P:Digital8 PB MODE ˇˇˇÿ TR MODEL C:Hi8/Std8 PB MODE PANEL_VD R4805 TRV MODEL:DCR-TRV120/TRV120E/TRV120P/TRV125E PANEL_HD 3.3k TR MODEL:DCR-TR8000E/TR8100E EVF_B EVF_R VC-235 BOARD (7/16) EVF_G/BW_Y PANEL_G ◊◊◊◊◊ Q4801...
Page 71: Digital8 Mechanism Control) Schematic Diagram
DCR-TRV120/TRV120E/TRV120P/TRV125E/ TR8000E/TR8100E VC-235 (Digital8 MECHANISM CONTROL) SCHEMATIC DIAGRAM • See page 4-11 for VC-235 printed wiring board. • See page 4-88 for waveforms. VC-235 BOARD (11/16) NTSC MODEL:DCR-TRV120/TRV120P PAL MODEL:DCR-TRV120E/TRV125E/TR8000E/TR8100E Digital8 MECHANISM CONTROL (MC BLOCK) -REF.NO.:10,000 SERIES- XX MARK:NO MOUNT...
Page 72: Camera Control, Hi8/Std8 Mechanism Control) Schematic Diagram
Drum speed servo 100k XSCK xBUSY EEP ROM VC_SO WEE2P Drum phase servo VC_SI Drum servo(speed and phase) MARKED:MOUNT TABLE Capstan speed servo MODEL DCR-TRV120/ DCR-TRV120E/ DCR-TR8000E/ REF.NO. TRV120P TRV125E TR8100E R1127 Capstan servo(speed and phase) R1128 100k 100k R1131...
Page 73: Servo) Schematic Diagram
VCC_2 R4448 VC-235 BOARD (8/16) S_REEL_- VCC_1 VCC_1 S_REEL_EVR REG_GND REG_GND DEW_AD DEW SENSOR FP-356 Q002 TAPE TOP FIEXIBLE Q001 NTSC MODEL:DCR-TRV120/TRV120P FP-249 TAPE END CN4404 PAL MODEL:DCR-TRV120E/TRV125E/TR8000E/TR8100E REG_GND REG_GND FIEXIBLE TAPE_TOP_C S001 TAPE_TOP(C) TAPE_TOP(C) HI8_MP_SW SIGNAL PATH HI8_MP HI8_MP...
Page 74 FP-249, FP-355, FP-356 (MECHA DECK) PRINTED WIRING BOARDS AND VC-235 (D/A CONVERTER) SCHEMATIC DIAGRAM • See page 4-11 for VC-235 printed wiring board. – Ref. No.: FP-249, FP-355, FP-356 flexible board; 10,000 series – NTSC MODEL:DCR-TRV120/TRV120P PAL MODEL:DCR-TRV120E/TRV125E/TR8000E/TR8100E VC-235 BOARD (14/16)
Page 75: Audio In/Out) Schematic Diagram
DCR-TRV120/TRV120E/TRV120P/TRV125E/ TR8000E/TR8100E VC-235 (AUDIO IN/OUT) SCHEMATIC DIAGRAM • See page 4-11 for VC-235 printed wiring board. VC-235 BOARD (15/16) AUDIO IN/OUT (AU BLOCK) -REF.NO.:10,000 SERIES- XX MARK:NO MOUNT NO MARK:REC/PB MODE R:REC MODE Hi8/Std8 P:Digital8 PB MODE VC-235 BOARD (9/16)
Page 76: Dc/Dc Converter) Schematic Diagram
DCR-TRV120/TRV120E/TRV120P/TRV125E/ TR8000E/TR8100E VC-235 (DC/DC CONVERTER) SCHEMATIC DIAGRAM • See page 4-11 for VC-235 printed wiring board. • See page 4-89 for waveforms. TRV MODEL:DCR-TRV120/TRV120E/TRV120P/TRV125E VC-235 BOARD (16/16) TR MODEL:DCR-TR8000E/TR8100E DC/DC CONVERTER(DD BLOCK) TRV MODEL -REF.NO.:10,000 SERIES- NO MARK:REC/PB MODE R:REC MODE...
Page 77: Se-104/113 Printed Wiring Board
ID-2 AUDIO/ VIDEO ID-2 LANC VTR REC MODEL DV IN/OUT DV OUT PLAYER MODEL VTR REC MODEL: DCR-TRV120/TRV120E: E, HK, AUS, CN, JE/TRV120P PLAYER MODEL: DCR-TRV120E: AEP, UK, EE, NE, RU/ TRV125E/TR8000E/TR8100E SE-104:1-676-772- SE-104:1-676-772- SE-113:1-676-753- SE-113:1-676-753- STEADY SHOT, AV IN/OUT...
Page 78 TR8000E/TR8100E SE-104/113 (STEADY SHOT, AV IN/OUT) SCHEMATIC DIAGRAM SE-104 BOARD (DCR-TRV120/TRV120E/TRV120P/TRV125E) STEADY SHOT,AV IN/OUT -REF.NO.:20,000 SERIES- SE-113 BOARD (DCR-TR8000E/TR8100E) XX MARK:NO MOUNT NO MARK:REC/PB MODE VTR REC MODEL:DCR-TRV120/TRV120E:E,HK,AUS,CN,JE/TRV120P PLAYER MODEL:DCR-TRV120E:AEP,UK,EE,NE,RU/TRV125E/TR8000E/TR8100E C203 R219 J202 TA A LANC CN202 R220 SE_GND R227...
Page 79: Printed Wiring Boards
DCR-TRV120/TRV120E/TRV120P/TRV125E/ TR8000E/TR8100E • For Printed Wiring Board. FP-156 (MIC/HP JACK, MF SENSOR), MI-37 (STEREO MIC AMP, IR TRANSMITTER) PRINTED WIRING BOARDS • MI-37 board is eight-layer print board. However, the patterns of – Ref. No.: FP-156 flexible board; 10,000/MI-37 board; 10,000 series –...
Page 80 DCR-TRV120/TRV120E/TRV120P/TRV125E/ TR8000E/TR8100E FP-156 FLEXIBLE BOARD J157 J156 (PLUG IN POWER) 1-676-818- 31 PH002 PH001 4-54 MIC/HP JACK, MF SENSOR STEREO MIC AMP, IR TRANSMITTER FP-156 MI-37 4-53...
Page 81: Stereo Mic Amp
DCR-TRV120/TRV120E/TRV120P/TRV125E/ TR8000E/TR8100E FP-156 (MIC/HP JACK, MF SENSOR), MI-37 (STEREO MIC AMP) SCHEMATIC DIAGRAM • See page 4-51 for FP-156 and MI-37 printed wiring boards. MI-37 BOARD (1/2) FP-156 CN5804 FLEXIBLE STEREO MIC AMP AU_GND HP_L HP_L HP_SENSE -REF.NO.:10,000 SERIES- HP_SENSE...
Page 82: Ir Transmitter) Schematic Diagram
DCR-TRV120/TRV120E/TRV120P/TRV125E/ TR8000E/TR8100E MI-37 (IR TRANSMITTER) SCHEMATIC DIAGRAM • See page 4-51 for MI-37 printed wiring board. • See page 4-89 for waveform. MI-37 BOARD (2/2) IR TRANSMITTER -REF.NO.:10,000 SERIES- SIGNAL PATH XX MARK:NO MOUNT VIDEO SIGNAL NTSC MODEL:TRV120/TRV120P AUDIO NO MARK:REC/PB MODE (IR ON)
Page 83 • There are few cases that the part isn't mounted in this model – Ref. No.: CF-69 board; 20,000 series – is printed on this diagram. – DCR-TRV120/TRV120E/TRV120P/TRV125E – • See page 4-93 for printed parts location. • Chip transistor...
Page 84 DCR-TRV120/TRV120E/TRV120P/TRV125E/ TR8000E/TR8100E USER CONTROL CF-69 4-61 4-62...
Page 85: Cf-69 Printed Wiring Board
DCR-TRV120/TRV120E/TRV120P/TRV125E/ TR8000E/TR8100E MF-10000 (CONTROL SWITCH BLOCK), CF-69 (USER CONTROL) SCHEMATIC DIAGRAM • See page 4-59 for CF-69 printed wiring boards. CF-69 BOARD (TRV120/TRV120E/TRV120P/TRV125E) CN004 USER CONTROL XVC_SCK XVC_SCK -REF.NO.:20,000 SERIES- XCS_LCD XCS_LCD_DA XX MARK:NO MOUNT VC_SO VC_SO NO MARK:REC/PB MODE...
Page 86: Cf-71 Printed Wiring Board
DCR-TRV120/TRV120E/TRV120P/TRV125E/ TR8000E/TR8100E MF-10000 (CONTROL SWITCH BLOCK), CF-71 (USER CONTROL) SCHEMATIC DIAGRAM • See page 4-67 for CF-71 printed wiring board. CF-71 BOARD (DCR-TR8000E/TR8100E) USER CONTROL -REF.NO.:30,000 SERIES- XX MARK:NO MOUNT NO MARK:REC/PB MODE CN001 EVF_VG EVF_VG EVF_VCO R029 EVF_4.75V EVF_BL EVF_BL EVF_13.3V...
Page 87 DCR-TRV120/TRV120E/TRV120P/TRV125E/ TR8000E/TR8100E • For Printed Wiring Board. CF-71 (USER CONTROL) PRINTED WIRING BOARD • There are few cases that the part isn't mounted in this model – Ref. No.: CF-71 board; 30,000 series – is printed on this diagram. – DCR-TR8000E/TR8100E –...
Page 88 DCR-TRV120/TRV120E/TRV120P/TRV125E/ TR8000E/TR8100E USER CONTROL CF-71 4-69 4-70...
Page 89: Fk-10000 Schematic Diagram
1500 D007 D008 S013,014 TLAU100B(TO5,SOY) TLAU100B(TO5,SOY) R015 PHOTO R014 D009 • CONTROL SWITCH BLOCK(FK-10000) TLAU100B(TO5,SOY) is replaced as a block. so that this PRINTED WIRING BOARD is omitted. VTR REC MODEL:DCR-TRV120/TRV120E:E,HK,AUS,CN,JE/TRV120P 4-71 CONTROL SWITCH BLOCK B/W EVF FK-10000 VF-129 4-72...
Page 90 DCR-TRV120/TRV120E/TRV120P/TRV125E/ TR8000E/TR8100E VF-129 (B/W EVF) SCHEMATIC DIAGRAM • See page 4-90 for waveforms. VF-129 BOARD T902 B/W EVF -REF.NO.:20,000 SERIES- XX MARK:NO MOUNT NTSC MODEL:DCR-TRV120/TRV120P PAL MODEL:DCR-TRV120E/TRV125E/TR8000E/TR8100E NO MARK:REC/PB MODE R :REC MODE Q904 2SD1819A-QRS-TX P :PB MODE VIDEO DRIVE -13.9...
Page 91 DCR-TRV120/TRV120E/TRV120P/TRV125E/ TR8000E/TR8100E • For Printed Wiring Board. PD-117 (RGB/CG LCD DRIVER, TIMING GENERATOR, BACK LIGHT) PRINTED WIRING BOARD • PD-117 board is four-layer print board. However, the patterns – Ref. No.: PD-117 board; 20,000 series – of layers 2 to 3 have not been included in the diagram.
Page 92 DCR-TRV120/TRV120E/TRV120P/TRV125E/ TR8000E/TR8100E BRIGHT BRIGHT – VOLUME+ VOLUME– 4-78 RGB/CG LCD DRIVER, TIMING GENERATOR, BACK LIGHT PD-117 4-77...
Page 93: Rgb Lcd Driver, Timing Generator) Schematic Diagram
GSRT/MODE2 R5567 (2.8) (2.6)<0.4> <0> TG15 XVC_SO GPCK/MODE1 (2.8) TYPE C MODEL:DCR-TRV120E:E,HK,AUS,CN,JE <2.2> XVD_OUT TG14 TYPE S 61k MODEL:DCR-TRV120/TRV120P VSYB GRES/EX1 (2.8) TYPE S 123k MODEL:DCR-TRV120E:AEP,UK,EE,NE,RU/TRV125E MARKED:MOUNT TABLE <0.4> TG13 CP/SPS MODEL MODEL REF.NO. TYPE S 61k MODEL TYPE S 123k MODEL TYPE C MODEL REF.NO.
Page 94 DCR-TRV120/TRV120E/TRV120P/TRV125E/ TR8000E/TR8100E PR-10000 (PANEL REVERSE SWITCH BLOCK), PD-117 (CG LCD DRIVER, BACK LIGHT) SCHEMATIC DIAGRAM • See page 4-75 for PD-117 printed wiring board. • See page 4-89 for waveforms. LCD INDICATION BLOCK ASSY R5710 CN5705 FP-94 PD-117 BOARD(2/2) (DCR-TRV120/TRV120E/TRV120P/TRV125E)
Page 95: Fu-138/143 Printed Wiring Board
DCR-TRV120/TRV120E/TRV120P/TRV125E/ TR8000E/TR8100E FU-138/143 (DC IN) PRINTED WIRING BOARD • For Printed Wiring Board. • There are few cases that the part isn't mounted in this model – Ref. No.: FU-138 board; 20,000 series – is printed on this diagram. • Chip transistor...
Page 96 D253 CHARGE CONTROL 01ZA8.2(TPL3) SWITCH TRV MODEL:DCR-TRV120/TRV120E/TRV120P/TRV125E VTR REC MODEL:DCR-TRV120/TRV120E:E,HK,AUS,CN,JE/TRV120P PLAYER MODEL:DCR-TRV120E:AEP,UK,EE,NE,RU/TRV125E/TR8000E/TR8100E The components identified by mark 0 or dotted Les composants identifiés par une marque 0 sont line with mark 0 are critical for safety. critiques pour la sécurité. Ne les remplacer que 4-86 Replace only with part number specified.
Page 97: Waveforms
4-3. WAVEFORMS CD-242 BOARD CD-244/269 BOARD VC-235 BOARD 1.92 Vp-p 544 mVp-p 7 Vp-p 7 Vp-p 0.4 Vp-p 2.26 Vp-p 720H: 27 MHz 960H: 36 MHz 41.85 MHz 13.3 msec 66 usec 66 usec IC101 1, 2 REC/PB IC151 1, 2 REC/PB IC1501 4 REC/PB IC2201 4 PB (Hi8/Std8) IC3301 <zzv REC/PB...
Page 98 MI-37 BOARD VF-129 BOARD PD-117 BOARD 608 mVp-p 560 mVp-p 2 Vp-p 1 Vp-p 1.96 Vp-p 440 kHz 20 MHz 16.7 msec IC4902 1 REC/PB IC1301 2 REC/PB IC3901 ra REC/PB (IR ON) IC5501 rk REC/PB IC901 1, 5 REC/PB 1.96 Vp-p 2 Vp-p 528 mVp-p...
Page 99: Parts Location
4-4. PARTS LOCATION [-12 $22, 32%] * : C1101 and R2256 are mounted on the board with suffix number VC-235 BOARD VC-235 BOARD SE-104/113 BOARD SE-104/113 BOARD MI-37 BOARD MI-37 BOARD (SIDE A) (SIDE B) (SIDE A) (SIDE B) (SIDE A) (SIDE B) C1320 C3203...
Page 100 CF-69 BOARD CF-69 BOARD CF-71 BOARD CF-71 BOARD PD-117 BOARD PD-117 BOARD (SIDE A) (SIDE B) (SIDE A) (SIDE B) (SIDE A) (SIDE B) CN003 BH001 BH001 CN001 C5504 C5501 CN008 CN005 C5505 C5503 C001 BZ001 CN008 C5506 C5508 D009 C5507 C5509 CN001...
Page 101: Adjustments
DCR-TRV120/TRV120E/TRV120P/TRV125E/ TR8000E/TR8100E SECTION 5 ADJUSTMENTS Before starting adjustment EVR Data Re-writing Procedure When Replacing Board The data that is stored in the repair board, is not necessarily correct. Perform either procedure 1 or procedure 2 or procedure 3 when replacing board.
Page 102: Adjusting Items When Replacing Main Parts And Boards
1-1. Adjusting items when replacing main parts and boards • Adjusting items when replacing main parts When replacing main parts, adjust the items indicated by z in the following table. Replaced part Block replacement Mounted part replacement Adjustment Section Adjustment Initialization of 7, 8, Initialization of 8, C, D page data C, D, E, F page data...
Page 103 • Adjusting items when replacing a board or EEPROM When replacing a board or EEPROM, adjust the items indicated by z in the following table. Note 1: TRV model (DCR-TRV120/TRV120E/ Replaced part TRV120P/TRV125E) only. Block Note 2: 720H model: DCR-TRV120/TRV120P...
Page 104: Camera Section Adjustment
Note 2: Connect the adjustment remote commander to the LANC commander is not the new micro processor (UPD7503G- jack, and set to HOLD switch to the “ADJ” side. Note 3: 720H model: DCR-TRV120/TRV120P C56-12), the pages cannot be switched. In this case, replace with the new micro processor (8-759-148-35).
Page 105: Preparations
Note 1: For details of how remove the cabinet and boards, refer to “2. DISASSEMBLY”. Note 2: When performing only the adjustments, the lens block and boards need not be disassembled. Note 3: TRV model: DCR-TRV120/TRV120E/TRV120P/TRV125E TR model: DCR-TR8000E/TR8100E 1.5 m CF board...
Page 106 TR model Note 1: Press the battery switch of the battery terminal using adhesive tape, etc. Regulated power supply (Note 1) (8.4 ± 0.1 Vdc) Color monitor Vector scope Video (yellow) Terminated 75 Ω Audio L (white) Adjustment remote commander Audio R (red) Battery Lens block...
Page 107 TRV model Note 1: Press the battery switch of the battery terminal using adhesive tape, etc. Note 2: 720H model: DCR-TRV120/TRV120P Regulated power 960H model: DCR-TR120E/TRV125E supply (Note 1) (8.4 ± 0.1 Vdc) Color monitor Vector scope Video (yellow) Terminated 75 Ω...
Page 108: Precaution
1-1-3. Precaution 1. Setting the Switch Unless otherwise specified, set the switches as follows and perform adjustments without loading cassette. Note: TRV model: DCR-TRV120/TRV120E/TRV120P/TRV125E POWER switch (SS-10000 block) ......CAMERA FOCUS switch (MF-10000) ......... MANUAL NIGHT SHOT switch (Lens block) ......... OFF PROGRAM AE (CF-69/71 board) ........
Page 109: Initialization Of 7, 8, C, D, E, F
1-2. INITIALIZATION OF 7, 8, C, D, E, F PAGE 3. 8 Page Table Note1: Fixed data-1: Initialized data. (Refer to “1. Initializing the DATA 8, C, D Page Data”) Note2: Fixed data-2: Modified data. (Refer to “2. Modified of 8, 1-2-1.
Page 110 4. C Page Table Initial value Address Remark Note1: Fixed data-1: Initialized data. (Refer to “1. Initializing the NTSC PAL 8, C, D Page Data”) E1 to E5 Fixed data-1 (Initialized data) Note2: Fixed data-2: Modified data. (Refer to “2. Modified of 8, Fixed data-2 C, D Page Data”) Fixed data-1 (Initialized data)
Page 111 5. D Page Table Initial value Address Remark Note1: Fixed data-1: Initialized data. (Refer to “1. Initializing the NTSC PAL 8, C, D Page Data”) 90 to A1 Fixed data-1 (Initialized data) Note2: Fixed data-2: Modified data. (Refer to “2. Modified of 8, VCO adj.
Page 112: Initialization Of 7, E, F
1-2-2. INITIALIZATION OF 7, E, F PAGE DATA 3. 7 Page Table 1. Initializing the 7, E, F Page Data Note1: Fixed data-1: Initialized data. (Refer to “1. Initializing the Note1: If “Initialization of Pages 7, E, F” is executed, all data on 7, E, F Page Data”) Note2: Fixed data-2: Modified data.
Page 113 4. E Page Table Initial value Address Remark Note1: Fixed data-1: Initialized data. (Refer to “1. Initializing the NTSC PAL 7, E, F Page Data”) Fixed data-1 (Initialized data) Note2: Fixed data-2: Modified data. (Refer to “2. Modified of 7, Fixed data-2 E, F Page Data”) Initial value...
Page 114 5. F Page Table Initial value Address Remark Note1: Fixed data-1: Initialized data. (Refer to “1. Initializing the NTSC PAL 7, E, F Page Data”) Flange back adj. Note2: Fixed data-2: Modified data. (Refer to “2. Modified of 7, E, F Page Data”) Initial value Remark Address...
Page 115: Camera System Adjustments
1-3. CAMERA SYSTEM ADJUSTMENTS Initial value Address Remark Before perform the camera system adjustments, Check that the NTSC PAL specified values of “27 MHz/36 MHz Origin Oscillation Adjustment”, Fixed data-1 (Initialized data) “S VIDEO OUT Y level Adjustment” and “S VIDEO OUT C level Fixed data-2 Adjustment”...
Page 116: Flange Back Adjustment
2. Flange Back Adjustment Adjusting method: (Using the minipattern box) 1) Install the minipattern box so that the distance between it and The inner focus lens flange back adjustment is carried out the front of the lens of the camcorder is less than 3 cm. automatically.
Page 117: More Than 500 M Away
3. Flange Back Adjustment 3-2. Flange Back Adjustment (2) (Using Flange Back Adjustment Chart Subject More Perform this adjustment after performing “Flange Back Adjustment Than 500 m Away) (1)”. The inner focus lens flange back adjustment is carried out Subject Subject more than 500m away automatically.
Page 118: Flange Back Check
4. Flange Back Check Subject Siemens star (PTB-450) (2.0 m from the front of the lens) (Luminance : approx. 200 lux) Measurement Point Check operation on TV monitor Measuring Instrument Specified Value Focused at the TELE end and WIDE end. Switch setting: 1) NIGHT SHOT ..............
Page 119: Optical Axis Adjustment
5. Optical Axis Adjustment Select page:F, address:60, and set correction data, then press Correct a deviation of optical axis between the lens and the CCD the PAUSE button on the adjusting remote commander. imager. 10) Shoot the Siemens Star with the zoom at TELE end. If deviated, the screen center will be shifted when the lens is zoomed 11) Change the lens direction so that the center of Siemens Star from TELE end to WIDE end.
Page 120: Picture Frame Setting
6. Picture Frame Setting Check on the oscilloscope Subject Color bar chart (PTB-450) 1. Horizontal period (Color reproduction adjustment frame) (1.5 m from the front of the lens) Measurement Point Video output terminal of A/V jack Measuring Instrument Oscilloscope and TV monitor Specified Value A=B, C=D, E=F Note: “Flange Back Adjustment”...
Page 121: Color Reproduction Adjustment
Adjustment Address 47, 49, D7, D8 Specified Value All color luminance points should settle within each color reproduction frame. Note: NTSC 720H model: DCR-TRV120/TRV120P PAL 960H model: DCR-TRV120E/TRV125E/TR8000E/ TR8100E Switch setting: NIGHT SHOT ..............OFF DIGITAL ZOOM (Menu display) ........OFF Burst position STEADY SHOT (Menu display) ........
Page 122: Awb & Lv Standard Data Input
Note 1: Perform “Auto White Balance Standard Data Input” before this adjustment. Note 2: Displayed data of page 1 of the adjustment remote commander. 1 : XX : XX Display data Note 3: NTSC 720H model: DCR-TRV120/TRV120P PAL 960H model: DCR-TRV120E/TRV125E/TR8000E/ TR8100E 5-22...
Page 123: White Balance Check
10. White Balance Check 2 mm Subject Clear chart (PTB-450) (Color reproduction adjustment frame) Filter Filter C14 for color temperature correction ND filter 1.0, 0.4 and 0.1 2 mm Measurement Point Video output terminal of A/V jack Measuring Instrument Vectorscope Fig.
Page 124: Angular Velocity Sensor Sensitivity Data Preset And Steady Shot Check
Note 1: Displayed data of page 1 of the adjustment remote commander. 1 : XX : XX Display data Note 2: NTSC model: DCR-TRV120/TRV120P PAL model: DCR-TRV120E/TRV125E/ TR8000E/TR8100E Adjusting method: 1) Select page: 0, address: 01, and set data: 01.
Page 125: Monochrome Electronic Viewfinder System Adjustments
1-4. MONOCHROME ELECTRONIC 1-4-2. Centering Adjustment VIEWFINEDER SYSTEM ADJUSTMENTS Mode Playback Note: NTSC model: DCR-TRV120/TRV120P Signal Hi8/standard 8 mm alignment tape : PAL model: DCR-TRV120E/TRV125E/TR8000E/TR8100E For checking operation (WR5-8NSE(NTSC)) 1-4-1. Horizontal Slant Check (WR5-8CSE(PAL)) Mode Playback Monoscope section Signal Hi8/standard 8 mm alignment tape : Specified Value ±...
Page 126: Aberration Adjustment
1-4-4. Aberration Adjustment 1-4-5. Horizontal Amplitude Adjustment (VF-129 board) Mode VTR stop Mode Playback Signal Dot pattern Signal Hi8/standard 8 mm alignment tape : 2 × a1 For checking operation Specified Value 0.8 × a2 (WR5-8NSE(NTSC)) (WR5-8CSE(PAL)) Monoscope section Adjustment method: 1) Adjust the aberration adjustment ring so that the tracing of the Adjusting Element C909 (SOL901)
Page 127: Vertical Amplitude Adjustment (Vf-129 Board)
1-4-6. Vertical Amplitude Adjustment (VF-129 board) 1-4-7. Brightness Adjustment (VF-129 board) Mode Playback Mode Playback Signal Hi8/standard 8 mm alignment tape : Signal Hi8/standard 8 mm alignment tape : For checking operation For checking operation (WR5-8NSE(NTSC)) (WR5-8NSE(NTSC)) (WR5-8CSE(PAL)) (WR5-8CSE(PAL)) Monoscope section Monoscope section Adjusting Element RV903...
Page 128: Lcd System Adjustments (Dcr-Trv120/Trv120E/Trv120P/Trv125E)
Set the LCD COLOR (Menu display) to the center. 2) Select page: C, and input the data in the following table. Note 4: TYPE S 61 k model: DCR-TRV120/TRV120P Note: To write in the non-volatile memory (EEPROM), press TYPE S 123 k model: DCR-TRV120E: AEP, UK, EE,...
Page 129: Lcd Initial Data Input (2)
Arbitrary Adjustment Address A0 to AA, AC to B1 Measurement Point Pin 8 of CN5502 (XHD OUT) Note: TYPE S 61 k model: DCR-TRV120/TRV120P Measuring Instrument Frequency counter TYPE S 123 k model: DCR-TRV120E: AEP, UK, EE, NE, Adjustment Page...
Page 130: Rgb Amp Adjustment (Pd-117 Board)
A=3.47 ± 0.07 Vp-p A=2.81 ± 0.05 Vp-p (TYPE C model) (TYPE S 61 k model) A=3.34 ± 0.07 Vp-p Note: TYPE S model: DCR-TRV120/TRV120E: AEP, UK, EE, (TYPE S 123 k model) NE, RU/TRV120P/TRV125E A=2.80 ± 0.07 Vp-p (TYPE C model)
Page 131: Com Amp Adjustment (Pd-117 Board)
A=6.33 ± 0.05 Vp-p (TYPE S model) Adjustment Address A=5.05 ± 0.05 Vp-p (TYPE C model) Note: Perform “Bright Adjustment” and “Contrast Adjustment” Note: TYPE S model: DCR-TRV120/ before this adjustment. TRV120E: AEP, UK, EE, NE, RU/ TRV120P/TRV125E Adjusting method: TYPE C model: DCR-TRV120E: E, HK, AUS, CN, JE Select page: 0, address: 01, and set data: 01.
Page 132: White Balance Adjustment (Pd-117 Board)
8. White Balance Adjustment (PD-117 board) Correct the white balance. If deviated, the LCD screen color cannot be reproduced. Mode Camera Subject Arbitrary Measurement Point Check on LCD display Measuring Instrument Adjustment Page Adjustment Address A8, A9 Specified Value The LCD screen should not be colored. Note 1: Check the white balance only when replacing the following parts.
Page 133: Mechanism Section Adjustment
Mechanism Adjustment Manual VII ”. Turn on the HOLD switch of the adjustment remote commander. Note 1: NTSC model: DCR-TRV120/TRV120P Select page: 0, address: 01, and set data: 01. PAL model: DCR-TRV120E/TRV125E/TR8000E/ Select page: 2, address: 2E, and set data: 02.
Page 134: Digital8 Mode
2-2. DIGITAL8 MODE 2-2-3. OVERALL TAPE PATH CHECK 2-2-1. HOW TO ENTER RECORD MODE WITHOUT 1. Recording of the tape path check signal CASSETTE 1) Clean the tape running side (tape guide, capstan shaft, pinch roller). 1) Connect the adjustment remote commander to the LANC jack. 2) Connect the adjustment remote commander to the LANC jack.
Page 135: Video Section Adjustment
Use the following measuring instruments for video section • For checking Standard 8 mode operations adjustments. For LP (WR5-4CL) Parts code: 8-967-995-56 Note: NTSC model: DCR-TRV120/TRV120P For SP (WR5-5CSP) PAL model: DCR-TRV120E/TRV125E/TR8000E/TR8100E Parts code: 8-967-995-47 Note: The following alignment tapes can also be used.
Page 136: Precautions On Adjusting
(R) block has been removed, the self-diagnosis data, data on history of use (total drum rotation time etc. ) will be lost. Before Note 4: TRV model: DCR-TRV120/TRV120E/TRV120P/TRV125E removing, note down the self-diagnosis data and data on history TR model: DCR-TR8000E/TR8100E use (data of page: 2, address: A2 to AA).
Page 137: Adjusting Connectors
3-1-3. Adjusting Connectors CN1108 Some of the adjusting points of the video section are concentrated at VC-235 board CN1108. Connect the measuring instruments via the CPC-13 jig (J-6082-443-A). The following table lists the pin numbers and signal names of CN1108. Pin No.
Page 138: Alignment Tape
3-1-5. Alignment Tape The following table lists alignment tapes which are available. Use the tape specified in the signal column for each adjustment. If the type of tape to be used for checking operations is not specified, use whichever type. Digital8 alignment tape Name Usage...
Page 139: Input/Output Level And Impedance
Fig. 5-3-3 Shows the color bar signals recorded on the alignment tape. Note: Measure using the VIDEO terminal (Terminated at 75 Ω). For NTSC model White (100%) White (75%) Burst signal 0.714 V (75%) 0.286 V Black 0.286 V White (100%) Horizontal sync signal Color bar signal waveform...
Page 140: System Control System Adjustment
3-2. SYSTEM CONTROL SYSTEM ADJUSTMENT 2-2. Input of Serial No. Write the serial No. and model code to the EEPROM (nonvolatile memory). 1. Initialization of 7, 8, C, D, E, F Page Data In writing the serial No., a decimal number should be converted into If the 7, 8, C, D, E, F page data is erased due to some reason, perform a hexadecimal number.
Page 141 0000 8192 2000 16384 4000 24576 6000 32768 8000 40960 A000 49152 C000 57344 E000 0100 8448 2100 16640 4100 24832 6100 33024 8100 41216 A100 49408 C100 57600 E100 0200 8704 2200 16896 4200 25088 6200 33280 8200 41472 A200 49664 C200...
Page 142: Battery End Adjustment (Vc-235 Board)
1) AUTO FOCUS ..............OFF Fig. 5-3-4 2) LCD screen (TRV model) ..........Closed 3) NIGHT SHOT ..............OFF Note 2: TRV model: DCR-TRV120/TRV120E/TRV120P/ TRV125E Connection: 1) Connect the regulated power supply and the digital voltmeter to the battery terminal as shown in Fig. 5-3-4.
Page 143: Servo And Rf System Adjustments
3-3. SERVO AND RF SYSTEM ADJUSTMENTS 2. PLL f & LPF f Pre-adjustment (VC-235 board) Before perform the servo and RF system adjustments, check that Mode VTR stop the specified value of “27 MHz/36MHz Origin Oscillation Measurement Point Display data of page: 3, address: 03 Adjustment”...
Page 144: Switching Position Adjustment (Vc-235 Board)
3. Switching Position Adjustment (VC-235 board) 4. AGC Center Level Adjustment (VC-235 board) To obtain normal playback waveform output, adjust the switching Mode Camera record and playback position. Subject Arbitrary Mode VTR playback Measurement Point Pin qh of CN1108 (RF MON) Signal Digital8 alignment tape : (Note 1)
Page 145: Apc & Aeq Adjustment (Vc-235 Board)
5. APC & AEQ Adjustment (VC-235 board) 6. PLL f & LPF f Final Adjustment (VC-235 board) Mode Camera record and playback Mode VTR stop Subject Arbitrary Signal Arbitrary Measurement Point Pin qh of CN1108 (RF MON) Measurement Point Display data of page: 3, address: 03 (Note 1) Measuring Instrument Adjustment remote commander...
Page 146: (Vc-235 Board)
7. Hi8/standard 8 mm Switching Position Adjustment 8. CAP FG Duty Adjustment (VC-235 board) (VC-235 board) Improve the capstan servo characteristic. If it is not correct. jitters If deviated in this case causes switching noise or jitter on the Hi8/ will increase.
Page 147: Video System Adjustments
36 MHz ... 960H model Check that the burst signal (B) is output to the chroma signal 720H model: DCR-TRV120/TRV120P terminal of S VIDEO jack. 960H model: DCR-TRV120E/TRV125E/TR8000E/ Select page: 3, address: 0C, set data: 04, and press the PAUSE TR8100E button.
Page 148: S Video Out Y Level Adjustment (Vc-235 Board)
3. S VIDEO OUT Y Level Adjustment (VC-235 board) 4. S VIDEO OUT Chroma Level Adjustment (VC-235 board) Mode VTR stop Mode VTR stop Subject Arbitrary Subject Arbitrary Measurement Point Y signal terminal of S VIDEO jack (75 Ω terminated) Measurement Point Chroma signal terminal of S VIDEO jack (75 Ω...
Page 149: Video Out Y, Chroma Level Check (Vc-235 Board)
5. VIDEO OUT Y, Chroma Level Check (VC-235 board) 6. Hi8/standard 8 mm AFC f Adjustment (VC-235 board) Mode VTR stop (Using Digital Voltmeter) Subject Arbitrary Adjust the pull-in range of the clock generator (IC2201) for A/D VIDEO jack (75 Ω terminated) Measurement Point conversion during Hi8/standard 8 mm playback.
Page 150: Ir Transmitter Adjustments
± 0.05 MHz (NTSC model) IR receiver jig Main unit f=11.55 ± 0.05 MHz (PAL model) VIDEO Note: NTSC model: DCR-TRV120/TRV120P 75 Ω (1-247-804-11) PAL model: DCR-TRV120E/TRV125E/TR8000E/TR8100E Fig. 5-3-15 Connection of Equipment Connect the measuring device as shown in the following figure, Adjusting method: and adjust.
Page 151: Ir Audio Deviation Adjustment (Mi-37 Board)
3. IR Audio Deviation Adjustment (MI-37 board) Adjusting method: Select page: 0, address: 01, and set data: 01. Mode VTR stop Only for the TR model (Note), Select page: D, address: 20, set Signal Audio signal: data: 01, and press the PAUSE button of the adjustment remote 400 Hz, –7.5 dBs: Audio left and commander.
Page 152: Audio System Adjustments
3-6. AUDIO SYSTEM ADJUSTMENTS 1. Hi8/standard 8 mm AFM BPF f Adjustment (VC-235 board) Sets the BPF passing frequency of IC5701 so that the AFM signal [Connecting the measuring instruments for the audio] can separate from the playback RF signal properly. If deviated. the Connect the audio system measuring instruments in addition to the mono/stereo mode will be differentiated incorrectly, and noises and video system measuring instruments as shown in Fig.
Page 153: Hi8/Standard 8 Mm Afm 1.5 Mhz Deviation Adjustment (Vc-235 Board)
2. Hi8/standard 8 mm AFM 1.5 MHz Deviation 4. Digital8 Playback Level Check Adjustment (VC-235 board) Mode VTR playback Adjust to the optimum 1.5 MHz audio FM signal deviation. Signal Digital8 alignment tape: If the adjustment is not correct, its playback level will differ from For audio operation check that of other units.
Page 154: Overall Noise Level Check
7. Overall Noise Level Check Mode Camera recording and playback Signal No signal: Insert a shorting plug in the MIC jack Measurement Point Audio left or right terminal of A/V jack Measuring Instrument Audio level meter Specified Value Below –45 dBs (IHF-A filter ON, 20 kHz LPF ON) Checking Method: 1) Insert a shorting plug in the MIC jack.
Page 155: Service Mode
2. Precautions Upon Using 5-4. SERVICE MODE the Adjustment Remote Commander Mishandling of the adjustment remote commander may erase the 4-1. ADJUSTMENT REMOTE COMMANDER correct adjustment data at times. To prevent this, it is recommended The adjustment remote commander is used for changing the that all adjustment data be noted down before beginning adjustments calculation coefficient in signal processing, EVR data, etc.
Page 156: Data Process
4-2. DATA PROCESS The calculation of the DDS display and the adjustment remote commander display data (hexadecimal notation) are required for obtaining the adjustment data of some adjustment items. In this case, after converting the hexadecimal notation to decimal notation, calculate and convert the result to hexadecimal notation, and use it as the adjustment data.
Page 157: Service Mode
4-3. SERVICE MODE 2. Emergence Memory Address 2-1. C Page Emergence Memory Address Additional note on adjustment Note: After the completion of the all adjustments, cancel the service Page C Address F4 to FF mode by either of the following ways. 1) After data on page: D and F is restored, unplug the main Address Contents...
Page 158: F Page Emergence Memory Address
2-2. F Page Emergence Memory Address 2-3. EMG Code (Emergency Code) Note 1: Emergence of PB mode only. Codes corresponding to the errors which occur are written in C page, addresses F4, F8 and FC (or F page, addresses 10, 14 and 18). The type of error indicated by the code are shown in the following Page F Address 10 to 1B...
Page 159: Msw Code
2-4. MSW Code • The lower parts of the data of C page, addresses F6, FA and FE (or F page, addresses 12, 16 and 1A) represent the MSW codes (mode switch mechanism position) when errors occurs. • The upper parts of the data of C page, addresses F6, FA and FE (or F page, addresses 12, 16 and 1A) represent, when the mechanism position is to be moved, the MSW codes at the start movement (when moving the loading motor).
Page 160: Bit Value Discrimination
3. Bit Value Discrimination Display on the Bit values Bit values must be discriminated using the display data of the adjustment bit3 bit2 bit1 bit0 adjustment remote commander for the following items. Us the table remote below to discriminate if the bit value is “1” or “0”. commander bit7 bit6...
Page 161: Record Of Use Check
CF-69 board TRV model Note 2: CF-71 board TR model TRV model: DCR-TRV120/TRV120E/TRV120P/TRV125E TR model: DCR-TR8000E/TR8100E Note 3: When the drum was replaced, initialize the drum rotation counted time. Initializing method of drum rotation counted time: Select page: 0, address: 01, and set data: 01.
Page 162: Switch Check (2)
(S001) Note: CF-69 board PD-117 board TRV model CF-71 board — TR model TRV model: DCR-TRV120/TRV120E/TRV120P/TRV125E TR model: DCR-TR8000E/TR8100E 9. Headphone Jack Check Page 3 Address 5A Function When bit value = 1 When bit value = 0 Headphone jack...
Page 163: Repair Parts List
DCR-TRV120/TRV120E/TRV120P/TRV125E/ SECTION 6 TR8000E/TR8100E REPAIR PARTS LIST 6-1. EXPLODED VIEWS The components identified by mark 0 or dotted line with mark 0 are critical for safety. NOTE: Replace only with part number speci- • -XX and -X mean standardized parts, so they may •...
Page 164: Cabinet (R) Section
6-1-2. CABINET (R) SECTION (TRV120/TRV120E/TRV120P/TRV125E) EVF block SP003 (See page 6-4) S008 LCD assembly (See page 6-5) not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-058-670-01 COVER (R) (101), HINGE (TRV120/TRV120P) * 58 3-059-650-01 BLIND (B) (101), VF 3-058-670-11 COVER (R) (101), HINGE (TRV120E/TRV125E) 1-418-801-11 SWITCH BLOCK, CONTROL (MF-10000) 3-948-339-61 TAPPING...
Page 165 6-1-3. CABINET (R) SECTION (TR8000E/TR8100E) EVF block (See page 6-4) LED904 not supplied (LCD904) not supplied not supplied The components identified by Les composants identifiés par une mark 0 or dotted line with marque 0 sont critiques pour la mark 0 are critical for safety. sécurité.
Page 166: Evf Block Section
6-1-4. EVF BLOCK SECTION V901 The components identified by Les composants identifiés par une mark 0 or dotted line with marque 0 sont critiques pour la mark 0 are critical for safety. sécurité. Replace only with part num- Ne les remplacer que par une pièce ber specified.
Page 167: Lcd Assembly Section (Trv120/Trv120E/Trv120P/Trv125E)
6-1-5. LCD ASSEMBLY SECTION (TRV120/TRV120E/TRV120P/TRV125E) ND901 LCD901 LED901 not supplied (LCD902) not supplied The components identified by Les composants identifiés par une mark 0 or dotted line with marque 0 sont critiques pour la mark 0 are critical for safety. sécurité.
Page 168: Cabinet (L) Section
6-1-6. CABINET (L) SECTION supplied Lens block (See page 6-7) Ref. No. Part No. Description Ref. page No. Ref. No. Part No. Description Ref. page No. 3-713-786-21 SCREW (M2X3) 1-418-800-41 SWITCH BLOCK, CONTROL (SS-10000) 3-968-729-01 SCREW (2X4) (TRV120E: AEP, UK, EE, NE, RU/TRV125E/ X-3950-223-1 CABINET (L) ASSY (TRV120/TRV120E: E, HK, TR8000E/TR8100E) AUS, CN, JE/TRV120P)
Page 169: Lens Block Section
6-1-7. LENS BLOCK SECTION supplied IC101, 151 (Note) M906 M905 (including A) (Note) Be sure to read “Precuations for Replcement of CCD Imager” on page 4-8, 4-10 when changing the CCD imager Ref. No. Part No. Description Ref. page No. Ref.
Page 170: Main Board Section
6-1-8. MAIN BOARD SECTION Mechanism deck (See page 6-9 to 6-11) Ref. No. Part No. Description Ref. page No. Ref. No. Part No. Description Ref. page No. 1-676-819-11 FP-157 FLEXIBLE BOARD A-7074-278-A SE-104 BOARD, COMPLETE A-7094-782-A VC-235 BOARD, COMPLETE (SERVICE) (TRV120E/TRV125E) (TRV120/TRV120P) A-7074-285-A SE-113 BOARD, COMPLETE...
Page 171: Cassette Compartment Assembly
6-1-9. CASSETTE COMPARTMENT ASSEMBLY LS chassis assembly (See page 6-10) Mechanism chassis assembly (See page 6-11) Ref. No. Part No. Description Ref. page No. Ref. No. Part No. Description Ref. page No. A-7040-421-A DAMPER ASSY X-3945-399-1 GEAR ASSY, GOOSENECK 7-624-102-04 STOP RING 1.5, TYPE -E 3-947-503-01 SCREW (M1.4) X-3949-153-2 CASSETTE COMPARTMENT ASSY 3-979-686-01 WASHER, STOPPER...
Page 172: Ls Chassis Assembly
6-1-10. LS CHASSIS ASSEMBLY S002 S001 D001 FP-249 (not supplied) Ref. No. Part No. Description Ref. page No. Ref. No. Part No. Description Ref. page No. A-7040-419-A BASE (S) BLOCK ASSY, GUIDE 3-965-579-01 ROLLER, PINCH PRESS A-7040-418-B BASE (T) BLOCK ASSY, GUIDE 3-965-563-01 GEAR, T SOFT 3-965-559-01 STOPPER (T) 3-965-565-01 CLAW, T SOFT...
Page 173: Mechanism Chassis Assembly
6-1-11. MECHANISM CHASSIS ASSEMBLY M901 81 1 M903 M902 S901 supplied Ref. No. Part No. Description Ref. page No. Ref. No. Part No. Description Ref. page No. 3-987-953-01 SPACER, RUBBER 3-965-542-01 SHIELD, MOTOR 3-965-550-02 SCREW (M1.7X1.6) 3-965-539-01 GEAR (A) 1-657-785-11 FP-248 FLEXIBLE BOARD 3-965-538-01 SLEEVE, MOTOR HOLDER 3-054-404-01 SPACER, CAPSTAN 3-965-540-01 HOLDER, MOTOR...
Page 174: Electrical Parts List
CD-242 CD-244/CD-269 CF-69 6-2. ELECTRICAL PARTS LIST The components identified by NOTE: mark 0 or dotted line with mark • Due to standardization, replacements in the • Items marked “*” are not stocked since they 0 are critical for safety. parts list may be different from the parts speci- are seldom required for routine service.
Page 175 CF-69 CF-71 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < CONNECTOR > < SWITCH > CN001 1-785-760-11 CONNECTOR, FFC/FPC (ZIF) 45P S001 1-771-138-61 SWITCH, KEY BOARD (DIGITAL EFFECT) * CN002 1-785-379-01 HOUSING, CONNECTOR S003 1-771-138-61 SWITCH, KEY BOARD (PICTURE EFFECT) CN003 1-778-506-21 PIN, CONNECTOR (PC BOARD) 2P S005...
Page 176 CF-71 FP-249 FP-355 FU-138/FU-143 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R007 1-216-833-91 RES-CHIP 1/16W S002 1-572-688-11 SWITCH, PUSH (1 KEY) (C LOCK) R009 1-216-816-11 METAL CHIP 1/16W R010 1-216-864-11 METAL CHIP 1/16W R011 1-216-822-11 METAL CHIP 1.2K 1/16W 1-658-213-11 FP-355 FLEXIBLE BOARD...
Page 177 FU-138/FU-143 MI-37 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark Q257 8-729-042-56 TRANSISTOR MGSF3455VT1 C3933 1-107-686-11 TANTALUM CHIP 4.7uF C3934 1-125-837-91 CERAMIC CHIP 6.3V < RESISTOR > C3935 1-164-943-11 CERAMIC CHIP 0.01uF C3936 1-164-943-11 CERAMIC CHIP 0.01uF R251 1-216-821-11 METAL CHIP...
Page 178 MI-37 PD-117 (TYPE S) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < COIL > R5826 1-218-963-11 RES-CHIP 6.8K 1/16W L3900 1-469-525-91 INDUCTOR 10uH R5827 1-218-968-11 RES-CHIP 1/16W L3901 1-469-525-91 INDUCTOR 10uH R5828 1-218-968-11 RES-CHIP 1/16W L3902 1-412-948-11 INDUCTOR 5.6uH...
Page 179 PD-117 (TYPE S) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C5606 1-107-826-91 CERAMIC CHIP 0.1uF R5506 1-216-826-11 METAL CHIP 2.7K 1/16W 0 C5607 1-131-959-91 CERAMIC CHIP 12PF R5507 1-216-841-11 METAL CHIP 1/16W C5608 1-104-851-11 TANTALUM CHIP 10uF R5508 1-216-843-11 METAL CHIP 1/16W...
Page 180 PD-117 (TYPE C) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-7074-290-A PD-117 (TYPE C) BOARD, COMPLETE (TRV120E: E, HK, AUS, CN, JE) < IC > ****************************** (Ref. No.: 20, 000 Series) IC5501 8-759-591-94 IC RB5P0030M1 IC5502 8-759-591-93 IC CM7019L3-T4 <...
Page 181 PD-117 (TYPE C) SE-104/SE-113 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R5616 1-216-810-11 METAL CHIP 1/16W < DIODE > R5617 1-216-837-11 METAL CHIP 1/16W R5618 1-216-817-11 METAL CHIP 1/16W D211 8-719-069-59 DIODE UDZS-TE17-8.2B R5702 1-216-822-11 METAL CHIP 1.2K 1/16W D212...
Page 182 VC-235 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-7094-782-A VC-235 BOARD, COMPLETE (SERVICE) C1347 1-135-216-11 TANTALUM CHIP 10uF (TRV120/TRV120P) (TRV120/TRV120E/TRV120P/TRV125E) A-7094-783-A VC-235 BOARD, COMPLETE (SERVICE) C1348 1-135-157-21 TANTALUM CHIP 10uF 6.3V (TRV120E/TRV125E) C1350 1-113-985-11 TANTALUM CHIP 10uF A-7094-784-A VC-235 BOARD, COMPLETE (SERVICE) C1351 1-164-943-11 CERAMIC CHIP...
Page 183 VC-235 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C1572 1-125-777-11 CERAMIC CHIP 0.1uF C3133 1-164-943-11 CERAMIC CHIP 0.01uF C2201 1-164-943-11 CERAMIC CHIP 0.01uF C3134 1-125-777-11 CERAMIC CHIP 0.1uF C2202 1-135-259-11 TANTALUM CHIP 10uF 6.3V C3135 1-164-874-11 CERAMIC CHIP 100PF C2203...
Page 184 VC-235 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C3335 1-125-777-11 CERAMIC CHIP 0.1uF C3732 1-126-246-11 ELECT 220uF C3337 1-125-837-91 CERAMIC CHIP 6.3V C3733 1-126-246-11 ELECT 220uF C3338 1-164-882-11 CERAMIC CHIP 220PF C3734 1-135-259-11 TANTALUM CHIP 10uF 6.3V C3342 1-125-837-91 CERAMIC CHIP...
Page 185 VC-235 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C4814 1-164-943-11 CERAMIC CHIP 0.01uF C5745 1-164-943-11 CERAMIC CHIP 0.01uF C4816 1-125-777-11 CERAMIC CHIP 0.1uF C5746 1-117-863-11 CERAMIC CHIP 0.47uF 6.3V C4817 1-125-777-11 CERAMIC CHIP 0.1uF C5747 1-117-863-11 CERAMIC CHIP 0.47uF 6.3V...
Page 186 VC-235 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark FB1503 1-500-284-21 INDUCTOR CHIP 0uH FB1504 1-414-760-21 FERRITE L1306 1-412-056-11 INDUCTOR 4.7uH FB1505 1-500-284-21 INDUCTOR CHIP 0uH L1307 1-412-056-11 INDUCTOR 4.7uH L1308 1-469-524-91 INDUCTOR 4.7uH FB2202 1-414-760-21 FERRITE L1309 1-469-524-91 INDUCTOR 4.7uH...
Page 187 VC-235 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark Q1309 8-729-046-98 TRANSISTOR CPH6702-TL (TRV120/TRV120E/TRV120P/TRV125E) Q4402 8-729-042-29 TRANSISTOR RN1104F (TPL3) Q1310 8-729-037-52 TRANSISTOR 2SC4738F-Y/GR (TPL3) Q4801 8-729-037-52 TRANSISTOR 2SC4738F-Y/GR (TPL3) Q1311 8-729-017-61 TRANSISTOR 2SB1581-T1 (TRV120/TRV120E/TRV120P/TRV125E) Q4802 8-729-037-52 TRANSISTOR 2SC4738F-Y/GR (TPL3) Q1312 8-729-037-53 TRANSISTOR 2SA1832F-Y/GR (TPL3) Q4803...
Page 188 VC-235 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R1134 1-218-990-11 SHORT R1343 1-208-931-11 METAL CHIP 0.5% 1/16W R1137 1-218-953-11 RES-CHIP 1/16W (TRV120/TRV120E/TRV120P/TRV125E) R1141 1-216-295-91 SHORT R1345 1-218-990-11 SHORT R1142 1-218-953-11 RES-CHIP 1/16W R1347 1-208-715-11 METAL CHIP 0.5% 1/16W R1143...
Page 189 VC-235 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R2242 1-218-967-11 RES-CHIP 1/16W R2243 1-218-967-11 RES-CHIP 1/16W R3215 1-208-939-11 METAL CHIP 150K 0.5% 1/16W R3305 1-218-990-11 SHORT R2244 1-218-966-11 RES-CHIP 1/16W R3308 1-218-990-11 SHORT R2245 1-218-949-11 RES-CHIP 1/16W R3309 1-218-990-11 SHORT...
Page 190 VC-235 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R3378 1-218-941-11 RES-CHIP 1/16W R4424 1-218-967-11 RES-CHIP 1/16W R3379 1-218-941-11 RES-CHIP 1/16W (TRV120/TRV120P) R3380 1-218-941-11 RES-CHIP 1/16W R4424 1-218-973-11 RES-CHIP 1/16W (TRV120E/TRV125E/TR8000E/TR8100E) R3381 1-218-941-11 RES-CHIP 1/16W R4425 1-218-959-11 RES-CHIP 3.3K 1/16W...
Page 191 VC-235 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R4803 1-218-977-11 RES-CHIP 100K 1/16W R4874 1-218-953-11 RES-CHIP 1/16W R4805 1-218-959-11 RES-CHIP 3.3K 1/16W (TR8000E/TR8100E) R4875 1-218-953-11 RES-CHIP 1/16W R4806 1-218-953-11 RES-CHIP 1/16W R4876 1-219-570-11 RES-CHIP 1/16W (TRV120/TRV120E/TRV120P/TRV125E) R4877 1-218-953-11 RES-CHIP...
Page 192 VC-235 VF-129 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R5702 1-218-990-11 SHORT < CAPACITOR > R5707 1-218-953-11 RES-CHIP 1/16W C901 1-107-854-11 TANTALUM CHIP 68uF 6.3V R5708 1-218-953-11 RES-CHIP 1/16W C902 1-163-038-91 CERAMIC CHIP 0.1uF R5709 1-218-973-11 RES-CHIP 1/16W C903...
Page 193 VF-129 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R917 1-218-891-11 METAL CHIP 0.5% 1/16W (TRV120/TRV120P) 1-758-216-21 FILTER BLOCK, OPTICAL (TRV120/TRV120P) 8-848-736-01 DEVICE, LENS LSV-680A R917 1-218-893-11 METAL CHIP 0.5% 1/16W 1-758-445-11 IRIS IR-680 (including FLEXIBLE BOARD) (TRV120E/TRV125E/TR8000/TR8100) 1-676-819-11 FP-157 FLEXIBLE BOARD R918...
Page 194 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark ACCESSORIES & PACKING MATERIALS 3-058-874-21 MANUAL, INSTRUCTION (SPANISH, PORTUGUESE) (TR8000E: AEP/TR8100E) ******************************** 3-058-874-31 MANUAL, INSTRUCTION (DUTCH, ITALIAN) 1-475-141-61 COMMANDER, REMOTE (RMT-814) (TR8000E: AEP/TR8100E) 1-475-599-11 ADAPTOR, AC (EXCEPT TRV120: KR) 1-475-599-71 ADAPTOR, AC (TRV120: KR) 3-058-874-41 MANUAL, INSTRUCTION (GERMAN, FRENCH) 1-569-007-11 ADAPTOR, CONVERSION 2P...
Page 195 DCR-TRV120/TRV120E/TRV120P/TRV125E/ TR8000E/TR8100E Sony Corporation 2000B0535-1 9-929-806-11 Personal VIDEO Products Company Printed in Japan © 2000. 2 – 254 – Published by Safety & Service Engineering Dept.

This manual is also suitable for:

Dcr-trv120e Dcr-tr8000e Dcr-tr8100e Dcr-trv120p Dcr-trv125e

Sony DCR-TRV120 Service Manual

Quick Links

Related Manuals for Sony DCR-TRV120

Summary of Contents for Sony DCR-TRV120

This manual is also suitable for:

Table of Contents