General - Sony AIR-SA10 Service Manual

AIR-SA10
Operations
Unit (AIR-SA10/Wireless Speaker System)
Setting the clock
1
Turn on the unit.
Press .
2
Select the clock set mode.
Press CLOCK/TIMER MENU
mode appears on the display, press
repeatedly to select "CLOCK, " and then press
CLOCK/TIMER ENTER
3
Set the time.
Press / repeatedly to set the hour, and
then press CLOCK/TIMER ENTER
same procedure to set the minute.
The clock settings are lost when you disconnect the
power cord or if a power failure occurs.
Listening to the sound of the
connected S-AIR main unit
You can use the S-AIR function to listen to the sound of
an S-AIR main unit in a remote location.
1
Perform the procedure described in "Preparing the
unit" and check that the S-AIR indicator
2
Press S-AIR CH repeatedly to select the desired
function of the S-AIR main unit.
The functions that can be selected depend on the
S-AIR main unit. For details, refer to the Operating
Instructions supplied with the S-AIR main unit.
3
Press VOLUME +/ to adjust the volume.
To operate the S-AIR main unit from the unit
You can perform the following operations using the
buttons on the unit.
Press To
Start playback of a CD/DVD,
etc.
Stop playback of a CD/DVD,
etc.
Pause playback of a CD/DVD,
etc.
/ Select a track, file or chapter
of a CD/DVD, etc.
PRESET +/ Select a preset station when
listening to the radio.
Depending on the connected S-AIR main unit,
the operation may differ. Refer to the Operating
Instructions of the S-AIR main unit.
To listen with headphones
Connect headphones (not supplied) to the
(headphone) jack located on the rear of the unit.
Note
The elapsed playing time or remaining playing time of the
CD/DVD, etc. being played on the S-AIR main unit may not
be displayed on this unit. In this case, "
Tip
You can listen to the sound even when the connected S-AIR
main unit is in standby mode. For details, refer to the Operating
Instructions supplied with the S-AIR main unit.
4
SECTION 2

GENERAL

Changing the display
To change the information on the display
while the unit is on
Press DISPLAY
display changes as follows:
. If the current
/
When the unit is connected to an S-AIR main unit:
Information of the connected S-AIR main unit
. Model name of the connected S-AIR main unit
2)3)
Clock ...
When the unit is not connected to an S-AIR main unit:
"S-AIR" "UNLINKED"
. Use the
To turn off the display
You can turn off the clock display to minimize the
amount of power consumed when the unit is off (Power
Saving Mode).
Press DISPLAY
display changes as follows:
No display (Power Saving Mode)
1) The displayed information depends on the connected S-AIR main
unit.
2) Displayed for about 8 seconds.
3)
Displayed only when the clock is set.
is lit.
Note
The STANDBY indicator
Using the Timers
The unit offers two timer functions. If you use the
Play Timer with the Sleep Timer, the Sleep Timer has
priority.
Sleep Timer:
Wireless strength
You can fall asleep to music. This function works even if
the clock is not set.
Press SLEEP
Note
Even if you set the timer, no sound is output from the unit if
playback on the connected S-AIR main unit ends within the set time
period or if communication with the S-AIR main unit is cut off.
Play Timer:
You can wake up to the sound of the connected S-AIR
main unit at a preset time.
Make sure you have set the clock.
1
Prepare the sound source on the S-AIR main unit.
For details, refer to the Operating Instructions
supplied with the S-AIR main unit.
Press VOLUME +/
2
Press CLOCK/TIMER MENU
3
Press /
then press CLOCK/TIMER ENTER
"ON TIME" appears, and the hour indication flashes.
4
Set the time to start playing.
Press /
then press CLOCK/TIMER ENTER
The minute indication flashes. Use the procedure
above to set the minute.
5
Use the same procedure as in step 4 to set the time
to stop playing.
. " appears.
6
. Each time you press the button, the
1)
2)
2) Clock 2)3) ...
. Each time you press the button, the
Clock 3) ...
lights up when the unit is off.
7
8
To stop the alarm
repeatedly.
Press any button.
To activate or check the timer again
1
2
3
4
To cancel the timer
1
to adjust the volume.
.
2
repeatedly to select "PLAY SET, "
3
.
4
To change the setting
repeatedly to set the hour, and
Start over from step 1.
.
Tip
The Play Timer setting remains as long as the setting is not canceled
manually.
This section is extracted
from instruction manual.
Press / repeatedly to select the desired
option.
AUTO:
Sound from the connected S-AIR main unit is
output. However, an alarm sounds in the following
cases.
When communication with the S-AIR main unit
is cut off.
When no sound is output from the S-AIR main
unit or the audio signal level is too low.
When the S-AIR main unit is not ready for
playback at the set start time. Note that the alarm
continues to sound even if the S-AIR main unit
becomes ready after the start time has passed.
ALARM:
An alarm is output.
S-AIR:
Sound from the connected S-AIR main unit is
output. However, sound from the S-AIR main unit
is not output in the following cases. An alarm does
not sound.
When communication with the S-AIR main unit
is cut off.
When no sound is output from the S-AIR main
unit or the audio signal level is too low.
When the S-AIR main unit is not ready for
playback at the set start time. Note that sound
from the S-AIR main unit is output once the S-
AIR main unit is ready for playback even after the
start time has passed.
Press CLOCK/TIMER ENTER .
The display shows the timer settings.
Press (on/standby) to turn off the unit.
The unit turns on about 40 seconds before the preset
time.
If the unit is on at the preset time, the Play Timer will
not play.
Press CLOCK/TIMER MENU .
"SELECT" flashes in the display.
Press CLOCK/TIMER ENTER .
Press / repeatedly to select "PLAY SEL. "
Press CLOCK/TIMER ENTER .
Press CLOCK/TIMER MENU .
"SELECT" flashes in the display.
Press CLOCK/TIMER ENTER .
Press / repeatedly to select "OFF. "
Press CLOCK/TIMER ENTER .