Page 1
LCD TV SERVICE MANUAL Modle list KL26AS21Q,KL26AS23Q,KL26AS25Q KL27BS23Q,KL32AS21Q,KL32AS22Q KL32BS23Q,KL32AS25Q,KL32BS28Q KL37BS21Q,KL37AS22Q,KL37AS23Q KL40BS21Q,KL42AS23Q KONKA GROUP CO,LTD. Digital Flat Display Division...
IMPORTANT SERVICE SAFETY INFORMATION Operating the receiver outside of its cabinet or with its back removed involves a shock hazard. Work on these models should only be performed by those who are thoroughly familiar with precautions necessary when working on high voltage equipment.
B. ADJUSTMENT MANUAL TEST NOTE 1. Please follow the pointed test steps and choose the right test equipment to conduct adjustment, otherwise good effect of Unit could not be obtained. The unit should be warmed up for 30 minutes before adjustment and every parameter should be adjusted repeatedly till the optimum value obtained, the pointed voltage value should be ensured during test to get satisfied test result.
Page 5
Update PC,ALL-11 1. Please refer to appendix 5.6 if HDCP KEY Debug Tool there is abnormal phenomenon. 1. Enter factory menu : Press MENU Enter factory button on the remote control, then menu Press PRE button per 5 times。 1. Enter factory menu, Select “VGA IIC SELECT”...
Page 6
1. .Enter factory menu, Select “Color c.VGA Color HDTV Video Enter black and Temp and Signal Generator white signal, Temp”, Select”7500”, chromaticity white-balanc VG848 Enter User menu, coordinates of white to fit the7500; Select “Color calibrate Color Signal Select”Memory” chromaticity adjust Generator Temp.
Page 7
Y,Pb,Pr HDTV Receiver SDTV: ATSC HDTV Play DVD 1.Screen is clear and fluent, Audio 576P/480P Tuner SDTV/HDTV checks if the output is normal。 HDTV: Component Cable (Y,Pr,Pb) 720p/1080i 1.Apiece Mode. Screen is clear and PC Mode Please fluent. VGA Cable refer to appendix 2.
Page 8
5. Appendix 5.1 Power Supply Board/ M/B Voltage confirmation 5.1.1 The input and output characteristic test of power 5.1.2 Intention of test: Check input and output to find if short circuit. 5.2 Checking Method: Use Multimeter (VICTOR VC9801) of resistor to check No/Yes short circuit. Number Item Test Point...
Page 9
5.3.7 Back light control signal (BKLON) of XS806 has high level (above 3V) or not, if not, check whether fault soldered or short circuit happened。 5.3.8 If back light lamp is on while there is no display, check N001 and N504’s reset circuit and the output of the oscillator to confirm the CPU and SCALER are working or not.If RGB is abnormal, check N504;If RGB is working correctly and the other channel is abnormal ,please check N504.
MARK1 MARK1 MARK2 MARK2 MARK3 MARK3 MARK4 MARK4 MARK5 MARK5 MARK6 MARK6 MARK7 MARK7 12VU mark mark mark mark mark mark mark mark mark mark mark mark mark mark xs805 pin1 and pin5 swaped F800 F800 XS805 XS805 HOLE HOLE HOLE HOLE HOLE...
Page 16
+3.3V V c c 3 . 3 f o r N805 N805 +3.3AVDD AVDD_DVI +3.3V VDDP D3.3V L516 L516 +3.3V d i g i t a l VOUT +3.3AVDD AVDDPLL2 CBW321611V121B/NC CBW321611V121B/NC C863 C863 + 3 . 3 V f o r C893 C893 C548...