Table of Contents
Advertisement
Turning off the sounds temporarily
From the remote control ONLY:
Press MUTING to turn off the sound through all
connected speakers and headphones.
"MUTING" appears on the display and the volume turns off.
EQ
C.TONE VIRTUAL SB AUDIO P. BASS TA NEWS INFO RDS TUNED ST
PL
LPCM
L
C
R
DOLBY D
NEO : 6
S . WFR
LFE
DTS AAC
DSP 3D
LS SB RS
96 / 24
AUTO SR
To restore the sound, press MUTING again.
• Pressing VOLUME +/– (or turning MASTER VOLUME control
on the front panel) also restores the sound.
Changing the display brightness
You can dim the display—Dimmer.
From the remote control ONLY:
Press DIMMER repeatedly.
• Each time you press the button, the display brightness changes
as follows:
DIMMER 1:
Dims the display slightly.
Dims the blue illumination slightly.
DIMMER 2:
Dims the display more than DIMMER 1.
Dims the blue illumination slightly (more than
DIMMER 1).
DIMMER 3:
Turns off the display and blue illumination.
(Temporarily canceled when you operate the
receiver.*)
DIMMER OFF: Cancels the Dimmer (normal display).
* Except when activating or deactivating TV Direct.
Turning off the power with the Sleep
Timer
You can fall asleep while listening to music—Sleep Timer.
From the remote control ONLY:
Press SLEEP repeatedly.
• Each time you press the button, the shut-off time changes in 10
minute intervals. The SLEEP indicator lights up on the display.
EQ
C.TONE VIRTUAL SB AUDIO P. BASS TA NEWS INFO RDS TUNED ST
LPCM
L
C
R
PL
DOLBY D
NEO : 6
S . WFR
LFE
DTS AAC
DSP 3D
LS SB RS
96 / 24
AUTO SR
10
20
30
OFF (canceled)
When the shut-off time comes:
The receiver turns off automatically.
To check or change the remaining time until the shut-off
time:
Press SLEEP once.
The remaining time (in minutes) until the shut-off time appears.
• To change the shut-off time, press SLEEP repeatedly.
AUTO MUTING
SLEEP
AUTO MODE
ATT
HP
MHz
kHz
SLEEP indicator
AUTO MUTING
SLEEP
AUTO MODE
ATT
HP
MHz
kHz
40
50
60
90
80
70
To cancel the Sleep Timer:
Press SLEEP repeatedly so that "SLEEP OFF" appears on the
display. (The SLEEP indicator goes off.)
• The Sleep Timer is also canceled when:
– You turn off the receiver, or
– TV Direct is activated.
Basic adjustment of auto memory
This receiver memorizes sound settings for each source:
• when you turn off the power, and
• when you change the source.
When you change the source, the memorized settings for the
newly selected source are automatically recalled.
The following can be stored for each source:
• Analogue/digital input mode (see page 12)
• Subwoofer audio position (see page 14)
• Midnight mode (see page 23)
• Speaker output level (see page 29)
• Digital equalization pattern (see page 30)
• Bass boost (see page 30)
• Subwoofer phase (see page 30)
• Input attenuator mode (see page 30)
• Surround/DSP mode selection (see pages 41 to 43)
NOTE
If the source is "FM" or "AM," you can assign a different setting
for each band.
Signal and speaker indicators on the display
Signal indicators
L
C
R
EQ
C.TONE VIRTUAL SB AUDIO P. BASS TA NEWS INFO RDS
S . WFR
LFE
LPCM
DOLBY D
S . WFR
DTS AAC
LS SB RS
LS
96 / 24
The signal indicators light up as follows:
L:
• When digital input is selected: Lights up when the
left channel signal comes in.
• When analogue input is selected: Always lights up.
R:
• When digital input is selected: Lights up when the
right channel signal comes in.
• When analogue input is selected: Always lights up.
C:
Lights up when the center channel signal comes in.
LS*: Lights up when the left surround channel signal comes
in.
RS*: Lights up when the right surround channel signal comes
in.
SB:
Lights up when the surround back channel signal
comes in.
LFE: Lights up when the LFE channel signal comes in.
* When monaural surround signal comes in, only "S" lights up.
NOTE
When "DVD MULTI" is selected as the source, all the signal
indicators except "SB" light up.
The speaker indicators light up as follows:
• The subwoofer indicator (
S . WFR
"SUBWOOFER" is set to "SUBWOOFER: YES." For details,
see page 21.
• The other speaker indicators light up only when the
corresponding speaker is set to "SMALL" or "LARGE," and
also when required for the current playback.
Speaker indicators
L
C
R
S . WFR
LFE
PL
L
C
R
NEO : 6
LFE
DSP 3D
LS SB RS
SB
RS
AUTO SR
) lights up when
15
Advertisement
Table of Contents
