Turning Off The Sounds Temporarily; Changing The Display Brightness; Turning Off The Power With The Sleep Timer - JVC RX-F31S Instructions Manual
Home cinema control system
Hide thumbs
Also See for RX-F31S:
- Instructions manual (55 pages) ,
- Service manual (65 pages) ,
- Service manual (65 pages)
Table of Contents
Advertisement
Turning off the sounds temporarily
From the remote control ONLY:
Press MUTING to turn off the sound through all
connected speakers and headphones.
“MUTING” appears on the display and the volume turns off.
EQ
C.TONE VIRTUAL SB AUDIO P. BASS TA NEWS INFO RDS TUNED ST
AUTO MUTING
SLEEP
AUTO MODE
LPCM
L
C
R
PL
ATT
DOLBY D
NEO : 6
HP
S . WFR
LFE
DTS AAC
DSP 3D
MHz
LS SB RS
96 / 24
AUTO SR
kHz
To restore the sound, press MUTING again.
• Pressing VOLUME +/– (or turning MASTER VOLUME control
on the front panel) also restores the sound.
Changing the display brightness
You can dim the display—Dimmer.
From the remote control ONLY:
Press DIMMER repeatedly.
• Each time you press the button, the display brightness changes
as follows:
DIMMER 1:
Dims the display slightly.
Dims the blue illumination slightly.
DIMMER 2:
Dims the display more than DIMMER 1.
Dims the blue illumination slightly (more than
DIMMER 1).
DIMMER 3:
Turns off the display and blue illumination.
(Temporarily canceled when you operate the
receiver.*)
DIMMER OFF: Cancels the Dimmer (normal display).
* Except when activating or deactivating TV Direct.
Turning off the power with the Sleep
Timer
You can fall asleep while listening to music—Sleep Timer.
From the remote control ONLY:
Press SLEEP repeatedly.
• Each time you press the button, the shut-off time changes in 10
minute intervals. The SLEEP indicator lights up on the display.
SLEEP indicator
EQ
C.TONE VIRTUAL SB AUDIO P. BASS TA NEWS INFO RDS TUNED ST
AUTO MUTING
SLEEP
AUTO MODE
PL
LPCM
L
C
R
ATT
DOLBY D
NEO : 6
HP
S . WFR
LFE
DSP 3D
MHz
DTS AAC
LS SB RS
96 / 24
AUTO SR
kHz
10
20
30
40
50
60
OFF (canceled)
90
80
70
When the shut-off time comes:
The receiver turns off automatically.
To check or change the remaining time until the shut-off
time:
Press SLEEP once.
The remaining time (in minutes) until the shut-off time appears.
• To change the shut-off time, press SLEEP repeatedly.
To cancel the Sleep Timer:
Press SLEEP repeatedly so that “SLEEP OFF” appears on the
display. (The SLEEP indicator goes off.)
• The Sleep Timer is also canceled when:
– You turn off the receiver, or
– TV Direct is activated.
Basic adjustment of auto memory
This receiver memorizes sound settings for each source:
• when you turn off the power, and
• when you change the source.
When you change the source, the memorized settings for the
newly selected source are automatically recalled.
The following can be stored for each source:
• Analog/digital input mode (see page 12)
• Subwoofer audio position (see page 14)
• Midnight mode (see page 24)
• Speaker output level (see page 29)
• Digital equalization pattern (see page 30)
• Bass boost (see page 30)
• Subwoofer phase (see page 30)
• Input attenuator mode (see page 30)
• Surround/DSP mode selection (see page 39)
NOTE
If the source is “FM” or “AM,” you can assign a different setting
for each band.
Signal and speaker indicators on the display
Signal indicators
Speaker indicators
L
C
R
L
C
R
EQ
C.TONE VIRTUAL SB AUDIO P. BASS
TA NEWS INFO RDS
S . WFR
LFE
S . WFR
LFE
PL x
LPCM
L
C
R
NEO : 6
DOLBY D
S . WFR
LFE
DTS AAC
DSP 3D
LS SB RS
LS SB RS
LS
SB
RS
96 / 24
AUTO SR
The signal indicators light up as follows:
L:
• When digital input is selected: Lights up when the
left channel signal comes in.
• When analog input is selected: Always lights up.
R:
• When digital input is selected: Lights up when the
right channel signal comes in.
• When analog input is selected: Always lights up.
C:
Lights up when the center channel signal comes in.
LS*: Lights up when the left surround channel signal comes
in.
RS*: Lights up when the right surround channel signal comes
in.
SB:
Lights up when the surround back channel signal
comes in.
LFE: Lights up when the LFE channel signal comes in.
* When monaural surround signal comes in, only “S” lights up.
NOTE
When “DVD MULTI” is selected as the source, all the signal
indicators except “SB” light up.
The speaker indicators light up as follows:
• The subwoofer indicator (
S . WFR
) lights up when
“SUBWOOFER” is set to “SUBWOOFER: YES.” For details,
see page 21.
• The other speaker indicators light up only when the
corresponding speaker is set to “SMALL” or “LARGE,” and
also when required for the current playback.
Page 15
Advertisement
Chapters
Table of Contents
Troubleshooting
