Page 1 SpeedTouch™516 /536 /546 (v6) (v6) (v6) Residential ADSL Gateway CLI Reference Guide...
Page 3 SpeedTouch™ /536 (v6) (v6) (v6) CLI Reference Guide...
Page 4: Document Information
Trademarks The following trademarks are used in this document: SpeedTouch™ is a trademark of THOMSON. Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. Ethernet™ is a trademark of Xerox Corporation. Wi-Fi® and the Wi-Fi logo are registered trademarks of the Wi-Fi Alliance. "Wi-Fi CERTIFIED", "Wi-Fi ZONE", "Wi-Fi Alli- ance", their respective logos and "Wi-Fi Protected Access"...
Page 5 Contents Contents About this Document ..................1 Root Commands .................... 3 ping................................4 traceroute..............................5 ADSL Commands................... 7 adsl config..............................8 adsl info................................. 9 ATM Commands ..................11 atm flush ..............................13 atm ifadd ..............................14 atm ifattach ..............................15 atm ifconfig..............................
Page 6: Table Of Contents
Contents atm oam ping ............................. 42 atm oam cc list ............................43 atm oam cc modify ............................ 44 atm oam cc send ............................45 atm oam vclb add............................46 atm oam vclb del............................47 atm oam vclb list ............................48 atm phonebook add ...........................
Page 7 Contents connection clear ............................83 connection config............................84 connection debug............................85 connection describe ........................... 86 connection flush ............................87 connection info............................88 connection list ............................89 connection refresh ............................. 90 connection stats ............................91 connection timerclear ..........................92 connection timerconfig..........................93 connection unbind .............................
Page 8 Contents dhcp relay add ............................124 dhcp relay debug stats..........................125 dhcp relay debug traceconfig........................126 dhcp relay config............................127 dhcp relay delete ............................128 dhcp relay flush ............................129 dhcp relay ifconfig............................ 130 dhcp relay iflist ............................132 dhcp relay list ............................133 dhcp relay modify ............................
Page 9 Contents dhcp server pool rtadd..........................169 dhcp server pool rtdelete......................... 170 dhcp server pool ruleadd......................... 171 dhcp server pool ruledelete........................172 DNS Commands..................173 dns client config ............................174 dns client dnsadd ............................. 175 dns client dnsdelete ..........................176 dns client dnslist............................177 dns client flush ............................
Page 10 Contents dsd urlfilter config ............................ 207 dsd urlfilter rule add..........................208 dsd urlfilter rule delete..........................209 dsd urlfilter rule flush..........................210 dsd urlfilter rule list ..........................211 dsd urlfilter rule modify ........................... 212 DynDNS Commands.................. 213 dyndns add ............................... 214 dyndns delete ............................
Page 11 Contents eth bridge dynvlan delete........................247 eth bridge dynvlan flush.......................... 248 eth bridge dynvlan list ..........................249 eth bridge flush ............................250 eth bridge ifadd ............................251 eth bridge ifattach ............................ 252 eth bridge ifconfig ............................ 253 eth bridge ifdelete ............................ 255 eth bridge ifdetach ...........................
Page 12 Contents expr add ..............................288 expr delete ..............................291 expr flush ..............................293 expr list..............................294 expr modify............................... 300 Firewall Commands................... 303 firewall config ............................304 firewall clear ............................. 306 firewall list..............................307 firewall chain add ............................. 308 firewall chain delete ..........................309 firewall chain flush ...........................
Page 13 Contents Hostmgr Commands ................. 341 hostmgr add ............................. 342 hostmgr clear............................344 hostmgr config ............................345 hostmgr delete ............................346 hostmgr flush ............................347 hostmgr list............................... 348 IDS Commands ..................349 ids clear ..............................350 ids config..............................351 ids parser list ............................352 ids parser modify .............................
Page 14 Contents Interface Commands ................. 381 interface list .............................. 382 IP Commands ..................... 385 ip arpadd ..............................387 ip arpdelete ............................... 388 ip arplist ..............................389 ip config ..............................390 ip flush............................... 392 ip ifadd ..............................393 ip ifattach ..............................394 ip ifconfig ..............................
Page 15 Contents ipqos config .............................. 428 ipqos list..............................430 ipqos ef config ............................431 ipqos ef list..............................432 ipqos ef stats............................. 433 ipqos queue clear ............................. 434 ipqos queue config........................... 435 ipqos queue list ............................437 ipqos queue stats ............................. 438 Label Commands ..................
Page 16 ............................... 505 mlp role removepriv ..........................506 NAT Commands..................507 nat config ..............................508 nat flush ..............................509 nat ifconfig ..............................510 nat iflist..............................511 nat mapadd............................... 512 nat mapdelete............................515 nat maplist ..............................516 E-DOC-CTC-20060414-0002 v1.0...
Page 17 Contents nat tmpladd............................... 517 nat tmpldelete............................520 nat tmpllist ..............................521 nat tmplinst............................... 522 PPP Commands..................523 ppp flush ..............................524 ppp ifadd ..............................525 ppp ifattach ............................... 526 ppp ifconfig............................... 528 ppp ifdelete ............................... 532 ppp ifdetach .............................. 533 ppp iflist ..............................
Page 18 Contents service host config ........................... 563 service host add ............................564 service host delete ........................... 565 service host disable..........................566 service host flush ............................. 567 service host list............................568 service host stats............................569 service host triggerlist ..........................570 service host rule add..........................571 service host rule delete..........................
Page 19 Contents sntp list..............................604 Software Commands................. 605 software upgrade ............................. 606 software version............................607 System Commands ................... 609 system config ............................610 system flush.............................. 612 system locale ............................613 system reboot............................615 system reset.............................. 616 system timedreboot ..........................617 system debug autosave........................... 618 system debug stats ..........................
Page 20 Contents user add ..............................642 user config ..............................644 user delete ..............................646 user flush ..............................647 user list..............................648 user rights ..............................650 Abbreviations ..................... 651 System Logging Messages ............... 655 Auto-PVC Module............................. 656 Configuration Module..........................656 DHCP Client Module..........................656 DHCP Relay Module ..........................
Page 21: About This Document
For the Service Provider, this Reference Guide aims to be a concise and practical document for creating a customized Service Template file, based on the SpeedTouch™ CLI command set, to be used by the end user to configure the SpeedTouch™ and computer(s).
Page 22 Documentation and software updates THOMSON continuously develops new solutions, but is also committed to improve its existing products. For suggestions regarding this document, please contact documentation.speedtouch@thomson.net. For more information on THOMSON's latest technological innovations, documents and software releases, visit us www.speedtouch.com...
Page 23: Root Commands
Root Commands Root Commands From the root prompt, you can choose one of the following commands: Command Description help Displays the help information. menu Displays the menu. exit Exits the shell. Exits group selection. saveall Saves current configuration. ping Send ICMP ECHO_REQUEST packets. traceroute Send ICMP/UDP packets to trace the ip path.
Page 24: Ping
Root Commands ping Send ICMP ECHO_REQUEST packets. SYNTAX: ping proto = <{ip|atm}> addr = <ip-address> dest = <string> [count = <number{0-1000000}>] [size = <number{28-20028}>] [interval(ms) = <number{100-1000000}>] [DF-bit = <{disabled|enabled}>] [srcaddr = <ip-address>] where: proto The interface type to be used. REQUIRED Choose between: addr...
Page 25: Traceroute
Root Commands traceroute Send ICMP/UDP packets to trace the IP path. SYNTAX: traceroute addr = <ip-address> [count = <number{1-10}>] [size = <number{1-20000}>] [interval = <number{1000-60000}>] [maxhops = <number{1-255}>] [dstport = <number{1-65535}>] [maxfail = <number{0-255}>] [type = <{icmp | udp}>] [utime = <{disabled | enabled}>] where: addr The destination IP address.
Page 26 Root Commands EXAMPLE: =>traceroute addr = 192.193.195.250 count=3 size=1 interval=1000 maxhops=30 dstport=33433 maxfail=5 type=icmp utime=yes :traceroute addr=192.193.195.250 ttl=1 192.193.195.250 676 us 1351 us 648 us => E-DOC-CTC-20060414-0002 v1.0...
Page 27: Adsl Commands
ADSL Commands ADSL Commands Introduction This chapter describes the commands of the adsl command group. Contents This chapter covers the following commands: adsl config Show/set the Asymmetric Digital Subscriber Line (ADSL) configuration. adsl info Display the ADSL statistics and information about the DSL line status. E-DOC-CTC-20060414-0002 v1.0...
Page 28: Adsl Config
The default is multi_adsl2plus. trace Enable or disable ADSL tracing. OPTIONAL The default is enabled. EXAMPLE: The example below shows the default configuration for a SpeedTouch™ ADSL/POTS variant: =>adsl config ADSL configuration: opermode = multi_adsl2plus trace = on modemoption = 00:00:00:00:00:00:00:00:00:00:00:00:00:00:00:00 =>...
Page 29: Adsl Info
ADSL Commands adsl info Display the ADSL statistics and information about the DSL line status. Although the same command is used for both SpeedTouch™ ADSL/POTS and SpeedTouch™ ADSL/ISDN variants, the command features specific output parameters and counters per variant. SYNTAX: adsl info EXAMPLE (for a SpeedTouch™...
Page 30 ADSL Commands E-DOC-CTC-20060414-0002 v1.0...
Page 31: Atm Commands
ATM Commands ATM Commands Introduction This chapter describes the commands of the atm command group. Contents This chapter covers the following commands: atm flush Flush all Asynchronous Transfer Mode (ATM) interfaces. atm ifadd Create a new ATM interface. atm ifattach Attach a ATM interface.
Page 32 ATM Commands atm oam vclb add Create a loopback connection for VC. atm oam vclb del Delete a loopback connection for VC. atm oam vclb list List all VC loopback connections. atm phonebook add Add a new phonebook entry. atm phonebook autolist Show the auto PVCs.
Page 33: Atm Flush
ATM Commands atm flush Flush all Asynchronous Transfer Mode (ATM) interfaces. SYNTAX: atm flush E-DOC-CTC-20060414-0002 v1.0...
Page 34: Atm Ifadd
ATM Commands atm ifadd Create a new ATM interface. SYNTAX: atm ifadd intf = <string> where: intf The name for the new ATM interface. REQUIRED Note If not specified, the destination parameter must be specified. In this case the name of the destination will double as interface name. EXAMPLE: =>atm iflist atm_0_35...
Page 35: Atm Ifattach
ATM Commands atm ifattach Attach a ATM interface. SYNTAX: atm ifattach intf = <string> where: intf The name of the ATM interface to be attached. REQUIRED EXAMPLE: =>atm iflist atm_0_35 : dest : atm_pvc_0_35 Retry : 10 QoS : default Encaps : vcmux Fcs : off Ulp : mac Connection State : connected RtPPPoA_atm: dest : RtPPPoA...
Page 36: Atm Ifconfig
This parameter is normally left disabled. retry A number between 0 and 65535. OPTIONAL Represents the number of times the SpeedTouch™ retries to set up a WAN connection before giving up. The default is 10. Select the Upper Layer Protocol (ULP) for this interface.
Page 37 ATM Commands EXAMPLE: =>atm iflist atm_0_35 : dest : atm_pvc_0_35 Retry : 10 QoS : default Encaps : llc Fcs : disabled Ulp : mac Connection State : connected atm_8_35 : dest : atm_pvc_8_35 Retry : 10 QoS : default Encaps : llc Fcs : disabled Ulp : mac Connection State : not-connected =>...
Page 38: Atm Ifdelete
ATM Commands atm ifdelete Delete an ATM interface. SYNTAX: atm ifdelete intf = <string> where: intf The name of the ATM interface to be deleted. REQUIRED EXAMPLE: =>atm iflist atm_0_35 : dest : atm_pvc_0_35 Retry : 10 QoS : default Encaps : vcmux Fcs : off Ulp : mac Connection State : connected RtPPPoA_atm: dest : RtPPPoA...
Page 39: Atm Ifdetach
ATM Commands atm ifdetach Detach an ATM interface. SYNTAX: atm ifdetach intf = <string> where: intf The name of the ATM interface to be detached. REQUIRED EXAMPLE: =>atm iflist atm_0_35 : dest : atm_pvc_0_35 Retry : 10 QoS : default Encaps : vcmux Fcs : off Ulp : mac Connection State : connected RtPPPoA_atm: dest : RtPPPoA...
Page 40: Atm Iflist
ATM Commands atm iflist Display the ATM interfaces. SYNTAX: atm iflist [intf = <string>] where: intf The name of the ATM interface to be shown. OPTIONAL Note If not specified, all the ATM interfaces are shown. EXAMPLE: =>atm iflist atm_0_35 : dest : atm_pvc_0_35 Retry : 10 QoS : default...
Page 41: Atm Bundle Add
ATM Commands atm bundle add Add a new bundle of interfaces. SYNTAX: atm bundle add name = <string> where: name The name of the new bundle. REQUIRED EXAMPLE: =>atm bundle add name=myBundle =>atm bundle list myBundle: Connection state : not-connected Retry: 10 Policy: priority Propagate: disabled...
Page 42: Atm Bundle Attach
ATM Commands atm bundle attach Attach a bundle of interfaces. SYNTAX: atm bundle attach name = <string> where: name The name of the bundle to be attached. REQUIRED EXAMPLE: =>atm bundle attach name=myBundle =>atm bundle list myBundle: Connection state : connected Retry: 10 Policy: priority Propagate: disabled...
Page 43: Atm Bundle Config
ATM Commands atm bundle config Modify a bundle of interfaces. The bundle of interfaces to be configured must not be connected at the time of configuration. If this should be the case, use the command :atm bundle detach before using the command :atm bundle config.
Page 44: Atm Bundle Clear
ATM Commands atm bundle clear Clear the bundle statistics. SYNTAX: atm bundle clear [name = <string>] where: name The name of the bundle for which the statistics must be cleared. OPTIONAL Note If not specified, the statistics for all the bundles will be cleared. E-DOC-CTC-20060414-0002 v1.0...
Page 45: Atm Bundle Delete
ATM Commands atm bundle delete Delete a bundle of interfaces. SYNTAX: atm bundle delete name = <string> where: name The name of the bundle to be deleted. REQUIRED RELATED COMMANDS: atm bundle add Add a new bundle of interfaces. atm bundle list Display the current bundles.
Page 46: Atm Bundle Detach
ATM Commands atm bundle detach Detach a bundle of interfaces. SYNTAX: atm bundle detach intf = <string> where: intf The name of the bundle to be detached. REQUIRED RELATED COMMANDS: atm bundle attach Attach a bundle of interfaces. E-DOC-CTC-20060414-0002 v1.0...
Page 47: Atm Bundle Flush
ATM Commands atm bundle flush Flush all bundles. SYNTAX: atm bundle flush E-DOC-CTC-20060414-0002 v1.0...
Page 48: Atm Bundle Ifadd
ATM Commands atm bundle ifadd Add an interface on a bundle. Up to 8 interfaces or (sub-)bundles can be added to one bundle. SYNTAX: atm bundle ifadd name = <string> intf = <string> [index = <number{0-6}>] where: name The name of the bundle to which an ATM interface must be added. REQUIRED intf The name of the ATM interface to be added.
Page 49: Atm Bundle Ifconfig
ATM Commands atm bundle ifconfig Configure an interface from a bundle. The interface to be configured must not be connected at the time of configuration. If this should be the case, use the command :atm bundle ifdetach before using the command :atm bundle ifconfig. SYNTAX: atm bundle ifconfig name = <string>...
Page 50: Atm Bundle Ifdelete
ATM Commands atm bundle ifdelete Remove an interface from a bundle. SYNTAX: atm bundle ifdelete name = <string> intf = <string> where: name The name of the bundle from which an ATM interface must be removed. REQUIRED intf The name of the ATM interface to be removed. REQUIRED EXAMPLE: =>atm bundle iflist...
Page 51: Atm Bundle List
ATM Commands atm bundle list Display the current bundles. SYNTAX: atm bundle list EXAMPLE: =>atm bundle list Test : Connection state : not-connected Retry: 10 Policy: priority TX requested bytes: 0 requested frames: 0 TX bytes: 0 frames: 0 RX bytes: 0 frames: 0 Interface: Test State: enabled...
Page 52: Atm Cac Config
ATM Commands atm cac config Configure the ATM connection admission control. SYNTAX: atm cac config config port = <{dsl0|dsl1|atm2|atm3|aal5|atm5} or number> state = <{disabled|enabled}> where: config port The port for which CAC is configured. REQUIRED state Enable/disable CAC for an ATM port. REQUIRED EXAMPLE: {Administrator}=>atm cac config...
Page 53: Atm Cac List
ATM Commands atm cac list Display all the CAC parameters. SYNTAX: atm cac list EXAMPLE: {Administrator}[atm cac]=>list CAC: port: dsl0 state: enabled CAC: port: dsl1 state: enabled CAC: port: atm2 state: enabled CAC: port: aal5 state: disabled CAC: port: atm5 state: disabled Overbooking: realtime: 0% non-realtime: 0%.
Page 54: Atm Cac Overbooking
ATM Commands atm cac overbooking Configure ATM overbooking parameters. SYNTAX: atm cac overbooking rt = <number{0-1000}> nrt = <number{0-1000}> where: A number between 0 and 1000. REQUIRED The realtime overbooking percentage. A number between 0 and 1000. REQUIRED The non-realtime overbooking percentage. EXAMPLE: {Administrator}[atm cac]=>overbooking rt 20 nrt 500 {Administrator}[atm cac]=>list...
Page 55: Atm Debug Aal5Stats
ATM Commands atm debug aal5stats Display ATM Adaptation Layer 5 (AAL5) port specific ATM statistics. SYNTAX: atm debug aal5stats port = <{dsl0|dsl1|atm2|atm3|aal5|atm5} or number> vpi = <number{0-15}> [vci = <number{0-511}>] [clear = <{disabled | enabled}>] where: port The port number for which statistics will be retrieved. REQUIRED Choose between: DSL0...
Page 56: Atm Debug Gstats
ATM Commands atm debug gstats Display ATM global statistics. SYNTAX: atm debug gstats [clear = <{disabled | enabled}>] where: clear Enable or disable clearing of the statistics after request. OPTIONAL EXAMPLE: {admin}[atm debug]=>gstats # of received octets = 1802. # of transmitted octets = 4346. # of received cells = 34.
Page 57: Atm Debug Portstats
ATM Commands atm debug portstats Display port specific ATM statistics. SYNTAX: atm debug portstats port = <{dsl0} or number> [clear = <{disabled | enabled}>] where: port The port number for which statistics will be retrieved. REQUIRED Choose between: DSL0 Or specify a port number (dsl0 has port number 0). clear Enable or disable clearing of the statistics after request.
Page 58: Atm Oam Config
ATM Commands atm oam config Modify the ATM Operation and Maintenance (OAM) settings. SYNTAX: atm oam config [clp = <number{0-1}>] [loopbackid = <string>] where: A number (0 or 1). OPTIONAL Represents the Cell Loss Priority (CLP) bit value of the OAM cells. The default is 1.
Page 59: Atm Oam List
ATM Commands atm oam list Display the ATM OAM settings. SYNTAX: atm oam list EXAMPLE: =>atm oam list OAM config dump ------------------- CLP bit value : 1 Loopback id : 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a OAM data blocking mode -------------------------- Port dsl0: blocking...
Page 60: Atm Oam Modify
ATM Commands atm oam modify Modify the ATM OAM data blocking mode. SYNTAX: atm oam modify port = <{dsl0} or number> blocking = <{disabled | enabled}> where: port The port for which OAM blocking is configured. REQUIRED Choose between: DSL0 Or specify a port number (dsl0 has port number 0).
Page 61 ATM Commands atm oam ping Send ATM loopback cells. E-DOC-CTC-20060414-0002 v1.0...
Page 62: Atm Oam Ping
ATM Commands atm oam ping Send ATM loopback cells. SYNTAX: atm oam ping dest = <string> [count = <number{1-1000000}>] [interval = <number{100-1000000}>] where: dest The destination address for the request. REQUIRED This can be any ATM phonebook entry. count A number between 1 and 1000000. OPTIONAL Represents the number of pings to send.
Page 63: Atm Oam Cc List
ATM Commands atm oam cc list Display Continuity Check (CC) configuration. SYNTAX: atm oam cc list EXAMPLE: =>atm oam cclist PORT = 0 VPI = 15 VCI = 16 End2End Mode = Auto Segment Mode = Auto PORT = 0 VPI = 0 VCI = 35 End2End Mode = Auto Segment Mode = Auto PORT = 0 VPI = 8 VCI = 35 End2End Mode = Auto Segment Mode = Auto...
Page 64: Atm Oam Cc Modify
Select the CC span. OPTIONAL Choose between: end2end: monitoring occurs on the entire VC between two ATM end stations. segment: monitoring occurs on a VC segment between the SpeedTouch™ and a first-hop ATM switch. RELATED COMMANDS: atm oam cc list Display Continuity Check (CC) configuration.
Page 65: Atm Oam Cc Send
Select the CC span. OPTIONAL Choose between: end2end: monitoring occurs on the entire VC between two ATM end stations. segment: monitoring occurs on a VC segment between the SpeedTouch™ and a first-hop ATM switch. action Activate or deactivate CC. OPTIONAL The default is deactivate.
Page 66: Atm Oam Vclb Add
ATM Commands atm oam vclb add Create a loopback connection for VC. SYNTAX: atm oam vclb add port = <{dsl0} or number> vpi = <number{0-15}> [vci = <number{0-511}>] where: port The ATM port number. REQUIRED Choose between: DSL0 Or specify a port number (dsl0 has port number 0). A number between 0 and 15.
Page 67: Atm Oam Vclb Del
ATM Commands atm oam vclb del Delete a loopback connection for VC. SYNTAX: atm oam vclb del port = <{dsl0} or number> vpi = <number{0-15}> [vci = <number{0-511}>] where: port The ATM port number. REQUIRED Choose between: DSL0 Or specify a port number (dsl0 has port number 0). A number between 0 and 15.
Page 68: Atm Oam Vclb List
ATM Commands atm oam vclb list List all VC loopback connections. SYNTAX: atm oam vclb list EXAMPLE: =>atm oam vclb list PORT = 0 VPI = 0 VCI = PORT = 1 VPI = 0 VCI = => RELATED COMMANDS: atm oam vclb add Create a loopback connection for VC.
Page 69: Atm Phonebook Add
ATM Commands atm phonebook add Add a new phonebook entry. SYNTAX: atm phonebook add name = <string> addr = <atmchannel : PVC syntax is [port.]vpi.vci port=dsl0 | ...> where: name The name of the new phonebook entry. REQUIRED This name can be freely chosen, however two limitations apply: The name of a phonebook entry intended for the Relayed PPPoA (PPPoA-to-PPTP Relaying) packet service may not start with capital P or capital T The name of a phonebook entry intended for the PPP-to-DHCP spoofing packet...
Page 70: Atm Phonebook Autolist
ATM Commands atm phonebook autolist Show the auto PVCs. Auto PVCs are only shown if they are supported by the Central Office DSLAM. SYNTAX: atm phonebook autolist EXAMPLE: =>atm phonebook autolist 8.35 => RELATED COMMANDS: atm phonebook list Display the current phonebook. E-DOC-CTC-20060414-0002 v1.0...
Page 71: Atm Phonebook Delete
ATM Commands atm phonebook delete Delete an existing phonebook entry. This command is only applicable for phonebook entries that are not used (in other words, not configured for any packet service). SYNTAX: atm phonebook delete name = <string> where: name The name of the phonebook entry to be deleted.
Page 72: Atm Phonebook Flush
ATM Commands atm phonebook flush Flush all the phonebook entries. 1. Phonebook entries that are in use, cannot be flushed. 2. This command does not impact previously saved configurations. SYNTAX: atm phonebook flush EXAMPLE: =>atm phonebook list Name Address atm_pvc_0_35 1 0.35 RtPPPoA 8.35...
Page 73: Atm Phonebook List
ATM Commands atm phonebook list Display the current phonebook. SYNTAX: atm phonebook list EXAMPLE: =>atm phonebook list Name Address atm_pvc_0_35 1 0.35 RtPPPoA 8.35 => RELATED COMMANDS: atm phonebook add Add a new phonebook entry. atm phonebook autolist Show the auto PVCs. atm phonebook delete Delete an existing phonebook entry.
Page 74: Atm Qosbook Add
ATM Commands atm qosbook add Add a new QoS book entry. SYNTAX: atm qosbook add name = <string> [txctd = <string>] [rxctd = <string>] where: name The name of the new QoS entry. REQUIRED txctd The name of the Conformance Traffic Descriptor (CTD) for the transmit (upstream) OPTIONAL direction.
Page 75: Atm Qosbook Config
ATM Commands atm qosbook config Modify the QoS book configuration. SYNTAX: atm qosbook config [format = <{bytes | cells}>] where: format The input/output format of the QoS book. OPTIONAL Choose between: bytes: the output is shown in Kbits or bytes. cells: the output is shown in cps or cells.
Page 76: Atm Qosbook Ctdadd
ATM Commands atm qosbook ctdadd Add a Connection Traffic Descriptor (CTD). SYNTAX: atm qosbook ctdadd name = <string> conformance = <{UBR | CBR | VBR }> [peakrate = <number{0-27786}>] [sustrate = <number{0-27786} [maxburst = <number{0-12240}>] [realtime = <{enabled | disabled}>] where: name The name of the new CTD.
Page 77 ATM Commands IMPORTANT NOTE: The SpeedTouch™ always rounds up specified burst sizes to a multiple of 48 bytes (a multiple of ATM cells). Example: In the example below a burst size of 100 bytes is specified (maxburst=100). The SpeedTouch™ will round up the burst size to the closest matching multiple of 48 bytes, as can be seen when displaying the profile via the command :atm qosbook ctdlist (burst=144).
Page 78: Atm Qosbook Ctddelete
ATM Commands atm qosbook ctddelete Delete a CTD. SYNTAX: atm qosbook ctddelete name = <string> [force = <{disabled | enabled}>] where: name The name of the CTD entry to be deleted. REQUIRED force Enable or disable to force delete the entry even when it is still in use. OPTIONAL The default is disabled.
Page 79: Atm Qosbook Ctdlist
ATM Commands atm qosbook ctdlist Display all CTDs. SYNTAX: atm qosbook ctdlist EXAMPLE: =>atm qosbook ctdlist Name Ref Conf Peak Sust Burst Minrate Frame Cdvt (Kbits) (Kbits) (bytes) (Kbits) (bytes) default 2 linerate 0 disabled disabled High 27786 disabled disabled =>...
Page 80: Atm Qosbook Delete
ATM Commands atm qosbook delete Delete a QoS book entry. SYNTAX: atm qosbook delete name = <string> [force = <{disabled | enabled}>] where: name The name of the QoS book entry to be deleted. REQUIRED force Enable or disable to force delete the entry even when it is still in use. OPTIONAL The default is disabled.
Page 81: Atm Qosbook Flush
ATM Commands atm qosbook flush Flush all the QoS book entries. The flush command does not impact previously saved configurations. SYNTAX: atm qosbook flush E-DOC-CTC-20060414-0002 v1.0...
Page 82: Atm Qosbook List
ATM Commands atm qosbook list Display the QoS book. SYNTAX: atm qosbook list EXAMPLE: =>atm qosbook list Name Ref Type TX peak sust burst RX peak sust burst framediscard (Kbits) (Kbits) (bytes) (Kbits) (Kbits) (bytes) default 3 linerate 0 linerate 0 disabled TestVBR 0 vbr-nrt 1500...
Page 83: Autopvc Commands
AutoPVC Commands AutoPVC Commands Introduction This chapter describes the commands of the autopvc command group. Contents This chapter covers the following commands: autopvc config Configure autopvc. autopvc list Show the retrieved information. E-DOC-CTC-20060414-0002 v1.0...
Page 84: Autopvc Config
AutoPVC Commands autopvc config Configure autopvc. SYNTAX: autopvc config [mode = <{pseudo | passive | active}>] [type = <{bridge | pppoerelay | ipoa | ethoa | pppoa | pppoe}>] [overwrite = <{disabled | enabled}>] [peakrate = <number{0-27786}>] where: mode Select the autopvc mode: OPTIONAL pseudo: only pseudo-ILMI (VP/VC 15/16) is enabled.
Page 85: Autopvc List
AutoPVC Commands autopvc list Show the retrieved information. SYNTAX: autopvc list [table = <{Port | AtmLayer | Vpc | Vcc | Address | AddressRegistrationAdmin | AtmServiceType | AtmServiceConnectionInfo | AAL1Profile | | AAL34Profile | AAL5Profile | AAL2CommonProfile | AAL2TrunkingProfile | AAL2LESProfile | AtmServiceConnInfoExtension | | AtmServiceTypeExtension | AAL5ProfileExtension}>] where:...
Page 86 AutoPVC Commands E-DOC-CTC-20060414-0002 v1.0...
Page 87: Config Commands
Config Commands Config Commands Introduction This chapter describes the commands of the config command group. Contents This chapter covers the following commands: config delete Delete a user configuration file. config dump Show the saved configuration file. config flush Flush the loaded configuration. config list Show the current configuration set.
Page 88: Config Delete
Name of the user configuration file to be deleted. OPTIONAL Note If not specified, all the user configuration files that were saved in the SpeedTouch™ permanent storage will be deleted. RELATED COMMANDS: config dump Show the saved configuration file. E-DOC-CTC-20060414-0002 v1.0...
Page 89: Config Dump
Config Commands config dump Show the saved configuration file. SYNTAX: config dump RELATED COMMANDS: config delete Delete a user configuration file. E-DOC-CTC-20060414-0002 v1.0...
Page 90: Config Flush
Config Commands config flush Flush the loaded configuration. 1. This flush command combines all the possible flush commands. 2. This command does not affect saved configurations. SYNTAX: config flush [flush_ip = <{enabled | disabled}>] where: flush_ip Flush IP settings (enabled) or not (disabled). OPTIONAL The default is enabled.
Page 91: Config List
Config Commands config list Show the current configuration set. SYNTAX: config list [templates = <{disabled | enabled}>] where: templates List the template files (disabled) or not (enabled). OPTIONAL The default is disabled. RELATED COMMANDS: config load Load complete saved (backup) or default configuration file. config save Store the current configuration in a backup file.
Page 92: Config Load
Config Commands config load Load complete saved (backup) or default configuration file. Use the command :config flush before loading a configuration file. SYNTAX: config load [load_ip = <{enabled | disabled}>] [defaults = <{enabled | disabled}>] [flush = <{enabled | disabled}>] [echo = <{disabled | enabled}>] [filename = <string>] where:...
Page 93: Config Save
Store the current configuration in a backup file. All the existing configurations and modifications entered by the user are saved. The backup file is saved in the SpeedTouch™ permanent storage. This file can be downloaded via the SpeedTouch™ web pages or via an FTP session.
Page 94 Config Commands E-DOC-CTC-20060414-0002 v1.0...
Page 95: Connection Commands
Connection Commands Connection Commands Introduction This chapter describes the commands of the connection command group. Contents This chapter covers the following commands: connection appconfig Configure the available CONN/NAT application helpers. connection appinfo Display CONN/NAT application specific info. connection applist List the available CONN/NAT application helpers. connection bind Create a new CONN/NAT application helper/port binding.
Page 96: Connection Appconfig
Connection Commands connection appconfig Configure the available CONN/NAT application helpers. SYNTAX: connection appconfig application = <string> [trace = <{disabled | enabled}>] [timeout = <number{0-32000}>] [floating = <{disabled | enabled}>] [tracelevel = <number{1-4}>] [SIP_ALG = <{disabled|enabled}>] [RTP_predict_for_term_SIP_ALG = <{disabled|enabled}>] where: application The name of a CONN/NAT application helper.
Page 97 Connection Commands EXAMPLE: =>connection applist Application Proto DefaultPort Traces Timeout IP6TO4 6to4 enabled unavailable PPTP 1723 enabled unavailable unavailable 15' 0" disabled 15' 0" FLOATING 5060 disabled 6 0" trace level 1 LOOSE(UDP) enabled 5' 0" enabled unavailable =>connection appconfig application=SIP trace=enabled =>connection applist Application Proto DefaultPort Traces...
Page 98: Connection Appinfo
Connection Commands connection appinfo Display CONN/NAT application specific info. SYNTAX: connection appinfo application = <{string}> where: application The name of a CONN/NAT application helper. REQUIRED Use the command :connection applist to obtain a list of CONN/NAT application helpers. EXAMPLE: =>connection appinfo application=SIP SIP ALG session SIPALG: pool=138, in use=0, bottom=138 =>...
Page 99: Connection Applist
Connection Commands connection applist List the available CONN/NAT application helpers. SYNTAX: connection applist EXAMPLE: =>connection applist Application Proto DefaultPort Traces Timeout IP6TO4 6to4 enabled unavailable PPTP 1723 enabled unavailable unavailable 15' 0" disabled 15' 0" FLOATING 5060 disabled 6 0" trace level 1 JABBER 5222...
Page 100: Connection Bind
Connection Commands connection bind Create a new CONN/NAT application helper/port binding. SYNTAX: connection bind application = <string> port = <port-range> where: application The name of a CONN/NAT application helper. REQUIRED Use the command :connection applist to obtain a list of CONN/NAT application helpers.
Page 101: Connection Bindlist
Connection Commands connection bindlist List the current CONN/NAT application helper/port bindings. SYNTAX: connection bindlist EXAMPLE: =>connection bindlist Application Proto Portrange Flags LOOSE(UDP) JABBER 15222 JABBER 5222 6660-6669 H323 1720 1002 RTSP RAUDIO(PNA) 7070 CU/SeeMe 7648 5060 PPTP 1723 IP6TO4 6to4 =>...
Page 102: Connection Clean
Connection Commands connection clean Clean the connection database by forcing timeouts. SYNTAX: connection clean [level = <number{0-9}>] where: level A number between 0 and 9. OPTIONAL Represents the desired scrubbing level. EXAMPLE: =>connection list proto state substate flags timeout ----- ----- -------- ----- -------...
Page 103: Connection Clear
Connection Commands connection clear Kill all the connections. SYNTAX: connection clear EXAMPLE: =>connection clear Connection to host lost. E-DOC-CTC-20060414-0002 v1.0...
Page 104: Connection Config
Connection Commands connection config Configure the connection handling. SYNTAX: connection config [configchangemode = <{immediate | delayed}>] [probes = <{disabled | enabled}>] [udptrackmode = <{strict | loose}>] where: configchangemode Select how configuration changes are handled. OPTIONAL Choose between: immediate delayed. The default is immediate. probes Enable or disable live probes on idle connections.
Page 105: Connection Debug
Connection Commands connection debug The connection debug commands SYNTAX: connection debug [trace = <{disabled|enabled}>] where: trace Enable or disable traces. OPTIONAL The default is disabled. EXAMPLE: =>connection debug connection traces : disabled => =>connection debug trace enabled => =>connection debug connection traces : enabled =>...
Page 106: Connection Describe
Connection Commands connection describe Describe the streams of a connection. SYNTAX: connection describe [id = <number{0-2048}>] where: A number between 0 and 2048. OPTIONAL Represents the ID of the connection to be described. Note If not specified, the connection with ID 0 will be described. Use the command :connection list to obtain the IDs of the different connections.
Page 107: Connection Flush
Connection Commands connection flush Flush the current connection configuration. SYNTAX: connection flush E-DOC-CTC-20060414-0002 v1.0...
Page 108: Connection Info
Connection Commands connection info Show all the registered modules with some info. SYNTAX: connection info EXAMPLE: =>connection info Registered connection modules : - Module : FW, holds private data (F:10264 S:6592). - Module : IDS, holds private data (F:0 S:0). - Module : NAT, holds private data (F:0 S:0).
Page 109: Connection List
Connection Commands connection list Display the currently known connections. SYNTAX: connection list [nr = <number{1-2048}>] where: A number between 1 and 2048. OPTIONAL Represents the number of connections to be displayed. Note If not specified, all the connections will be displayed. EXAMPLE: =>connection list proto state...
Page 110: Connection Refresh
Connection Commands connection refresh Invalidate all the cached decisions. SYNTAX: connection refresh E-DOC-CTC-20060414-0002 v1.0...
Page 111: Connection Stats
Connection Commands connection stats Display the connection and stream statistics. SYNTAX: connection stats EXAMPLE: =>connection stats Connection statistics: ------------------------------------------- Maximum number of connections : 1024 Maximum number of halfopen connections : 1024 ------------------------------------------- Number of active connections Number of halfopen connections Number of expected connections Number of closing connections Number of idle connections...
Page 112: Connection Timerclear
Connection Commands connection timerclear Clear the connection timeout to default. SYNTAX: connection timerclear [timer = <{tcpidle|tcpneg|tcpkill|udpidle|udpkill| icmpkill|ipidle|ipkill}>] where: timer The name of the connection idle timer to be reset. REQUIRED Note If not specified, all the timers will be reset to their default values. EXAMPLE: =>connection timerconfig tcpidle...
Page 113: Connection Timerconfig
Connection Commands connection timerconfig Configure the connection timeout handling. SYNTAX: connection timerconfig [timer = <{tcpidle|tcpneg|tcpkill|udpidle|udpkill| icmpkill|ipidle|ipkill}>] [value = <number{0-86400}>] where: timer The name of the connection idle timer to be configured. OPTIONAL Choose between: tcpidle tcpneg tcpkill udpidle udpkill icmpkill ipidle ipkill value...
Page 114: Connection Unbind
Connection Commands connection unbind Delete an existing CONN/NAT application helper/port binding. SYNTAX: connection unbind application = <string> port = <port-range> where: application The name of a CONN/NAT application helper. REQUIRED Use the command :connection applist to obtain a list of CONN/NAT application helpers.
Page 115: Cwmp Commands
CWMP Commands CWMP Commands Introduction This chapter describes the commands of the cwmp (CPE WAN Management Protocol) command group. Contents This chapter covers the following commands: cwmp config Configure the cwmpd as seen from the ACS. cwmp server config Configure the cwmpd towards the ACS. E-DOC-CTC-20060414-0002 v1.0...
Page 116: Cwmp Config
CWMP Commands cwmp config Configure the cwmpd as seen from the ACS. SYNTAX: cwmp config [state = <{disabled|enabled}>] [mode = <{readonly|full}>] [periodicInform = <{disabled|enabled}>] [periodicInfInt = <number>] [sessionTimeout = <number>] [noIpTimeout = <number>] [maxEnvelopes = <number>] [connectionRequest = <{disabled|enabled}>] [connectionReqPath = <string>] [connectionReqUserName = <string>] [connectionReqPsswd = <string>] [connectionReqAuth = <{none|basic|digest}>]...
Page 117 CWMP Commands connectionRequest Set the connection request flag of the cwmp daemon. OPTIONAL Choose between: enabled disabled. The default is enabled. connectionReqPath Set the path where the cwmp daemon can be reached. OPTIONAL connectionReqUserName Set the username the ACS must use to log in. OPTIONAL connectionReqPsswd Set the password the ACS must use to log in.
Page 118: Cwmp Server Config
CWMP Commands cwmp server config Configure the cwmpd towards the ACS. SYNTAX: cwmp server config [url = <string>] [username = <string>] [password = <string>] where: Set the HTTP URL used to contact the ACS server. OPTIONAL username Set the username for ACS Digest Authentication. OPTIONAL password Set the password for ACS Digest Authentication.
Page 119: Debug Commands
Debug Commands Debug Commands Introduction This chapter describes the commands of the debug command group. Contents This chapter covers the following commands: debug exec Execute a 'Trace & Debug' command. E-DOC-CTC-20060414-0002 v1.0...
Page 120: Debug Exec
Debug Commands debug exec Execute a 'Trace & Debug' command. This command is for qualified personnel only. SYNTAX: debug exec cmd = <quoted string> where: A quoted 'Trace & Debug' command string. REQUIRED E-DOC-CTC-20060414-0002 v1.0...
Page 121: Dhcp Commands
DHCP Commands DHCP Commands Introduction This chapter describes the commands of the Dynamic Host Configuration Protocol (DHCP) command group. Contents This chapter covers the following commands: dhcp client flush Delete all the DHCP leases. dhcp client ifadd Create a DHCP client. dhcp client ifattach Activate a DHCP client.
Page 122 DHCP Commands dhcp relay ruledelete Delete a selection rule from a DHCP forward entry. dhcp rule add Add a rule for DHCP conditional selection. dhcp rule debug traceconfig Modify DHCP rule trace configuration. dhcp rule delete Delete a DHCP rule. dhcp rule flush Flush all DHCP rules.
Page 123: Dhcp Client Flush
DHCP Commands dhcp client flush Delete all the DHCP leases. The flush command does not impact previously saved configurations. SYNTAX: dhcp client flush E-DOC-CTC-20060414-0002 v1.0...
Page 124: Dhcp Client Ifadd
DHCP Commands dhcp client ifadd Create a DHCP client. SYNTAX: dhcp client ifadd intf = <string> [defrqoptions = <{disabled|enabled}>] where: intf The name of the dynamic interface for which a DHCP lease must be created. REQUIRED defrqoptions Enable/Disable the creation of the default Parameter Request List. OPTIONAL EXAMPLE: =>dhcp client iflist...
Page 125: Dhcp Client Ifattach
=>dhcp client iflist myPPP_ppp : [INIT] flags = bc dns rt IP address : 0.0.0.0 HW address [SpeedTouch] : 00 DHCP server: 255.255.255.255 metric : rt = 1, DNS = 1 Number of leases: 1 Total size of table: 36, in use: 1, free: 97 % =>dhcp client ifattach intf=myPPP_ppp...
Page 126: Dhcp Client Ifconfig
DHCP Commands dhcp client ifconfig Configure a DHCP client. Use the command :dhcp client ifrelease before configuring the dhcp client. SYNTAX: dhcp client ifconfig intf = <string> [label = <label name>] [metric = <number{0-255}>] [dnsmetric = <number{0-100}>] [broadcast = <{disabled|enabled}>] where: intf The name of the dynamic interface to be configured.
Page 127: Dhcp Client Ifdelete
EXAMPLE: =>dhcp client iflist myPPP_ppp : [INIT] flags = bc dns rt IP address : 10.0.0.1 HW address [SpeedTouch] : 00:90:d0:01:47:f1 DHCP server: 10.10.1.1 hostname : myHostName client identifier : [00] myClientID user class identifier : myUserID metric : rt = 1, DNS = 1...
Page 128: Dhcp Client Ifdetach
DHCP Commands dhcp client ifdetach De-activate a DHCP client and releases its lease. SYNTAX: ifdetach intf = <string> where: intf The name of the dynamic interface. REQUIRED RELATED COMMANDS: dhcp client ifattach Activate a DHCP client. dhcp client ifrenew Renew the DHCP lease. dhcp client iflist List all the DHCP leases attached to dynamic interfaces.
Page 129: Dhcp Client Iflist
Total size of table: 36, in use: 1, free: 97 % => EXAMPLE INPUT/OUTPUT IN A NETWORKED ENVIRONMENT: The SpeedTouch™ is configured as DHCP client disabled its Ethernet interface eth0. =>dhcp client iflist myPPP_ppp : [INIT] flags = bc dns rt IP address : 10.0.0.1...
Page 130 DHCP Commands dhcp client ifdelete Delete a DHCP client. E-DOC-CTC-20060414-0002 v1.0...
Page 131: Dhcp Client Ifrenew
DHCP Commands dhcp client ifrenew Renew the DHCP lease. SYNTAX: dhcp client ifrenew intf = <string> where: intf The name of the dynamic interface for which the DHCP lease must be renewed. REQUIRED EXAMPLE 1: =>dhcp client iflist NewETHoA [BOUND] flags= IP address 10.0.0.10...
Page 132 DHCP Commands EXAMPLE 2: The SpeedTouch™ is configured as DHCP client disabled its Ethernet interface eth0. =>dhcp client stats DHCP client statistics: Corrupted packet recv OFFERs recv ACKs recv NAKs recv Pure BOOTP REPLIES Other message types DISCOVERs sent REQUESTs sent...
Page 133: Dhcp Client Debug Clear
DHCP Commands dhcp client debug clear Clear the DHCP client statistics. SYNTAX: dhcp client debug clear EXAMPLE: =>dhcp client debug stats DHCP client statistics: Corrupted packet recv OFFERs recv ACKs recv NAKs recv Pure BOOTP REPLIES Other message types DISCOVERs sent REQUESTs sent DECLINEs sent RELEASEs...
Page 134: Dhcp Client Debug Stats
DHCP Commands dhcp client debug stats Print the DHCP client statistics. SYNTAX: dhcp client debug stats EXAMPLE: =>dhcp client debug stats DHCP client statistics: Corrupted packet recv OFFERs recv ACKs recv NAKs recv Pure BOOTP REPLIES Other message types DISCOVERs sent REQUESTs sent DECLINEs sent RELEASEs...
Page 135: Dhcp Client Debug Traceconfig
DHCP Commands dhcp client debug traceconfig Modify the DHCP client trace configuration. SYNTAX: dhcp client debug traceconfig [state = <{disabled | enabled}>] where: state Enable or disable tracing. OPTIONAL The default is disabled. EXAMPLE: =>dhcp client debug traceconfig tracing: disabled =>dhcp client debug traceconfig trace=enabled =>dhcp client debug traceconfig tracing: enabled...
Page 136: Dhcp Client Rqoptions Add
DHCP Commands dhcp client rqoptions add Add a DHCP Option Code to the Parameter Request List. SYNTAX: dhcp client rqoptions add intf = <string> option = <string or number> [index = <number{0-255}>] where: intf The name of the dynamic interface. REQUIRED option The name or number of the option.
Page 137: Dhcp Client Rqoptions Delete
DHCP Commands dhcp client rqoptions delete Delete a DHCP Option Code from the Parameter Request List. SYNTAX: dhcp client rqoptions delete intf = <string> option = <string or number> where: intf The name of the dynamic interface. REQUIRED option The name or number of the option. OPTIONAL RELATED COMMANDS: dhcp client rqoptions list...
Page 138: Dhcp Client Rqoptions List
DHCP Commands dhcp client rqoptions list List all DHCP Option Codes in the Parameter Request List. SYNTAX: dhcp client rqoptions list [intf = <string>] where: intf The name of the dynamic interface. OPTIONAL RELATED COMMANDS: dhcp client rqoptions delete Delete a DHCP Option Code from the Parameter Request List. E-DOC-CTC-20060414-0002 v1.0...
Page 139: Dhcp Client Rqoptions Optionlist
DHCP Commands dhcp client rqoptions optionlist List all DHCP Option Codes that can be used in the Parameter Request List. SYNTAX: dhcp client rqoptions optionlist RELATED COMMANDS: dhcp client rqoptions Add a DHCP Option Code to the Parameter Request List. dhcp client rqoptions List all DHCP Option Codes in the Parameter Request List.
Page 140: Dhcp Client Txoptions Add
DHCP Commands dhcp client txoptions add Add an option. SYNTAX: dhcp client txoptions add intf = <string> option = <string or number> value = <Value : (type)value; type being 8-bit, 16-bit, 32-bit, addr, ascii, byte_array, clientid> [index = <number{0-255}>] where: intf The name of the dynamic interface.
Page 141: Dhcp Client Txoptions Delete
DHCP Commands dhcp client txoptions delete Delete an option. SYNTAX: dhcp client txoptions delete intf = <string> option = <string or number> where: intf The name of the dynamic interface. REQUIRED option The name or number of the option. REQUIRED RELATED COMMANDS: dhcp client txoptions list List all options.
Page 142: Dhcp Client Txoptions List
DHCP Commands dhcp client txoptions list List all options. SYNTAX: dhcp client txoptions list RELATED COMMANDS: dhcp client txoptions delete Delete an option. E-DOC-CTC-20060414-0002 v1.0...
Page 143: Dhcp Client Txoptions Optionlist
DHCP Commands dhcp client txoptions optionlist Lists all DHCP Option Codes that can be used. SYNTAX: dhcp client txoptions optionlist RELATED COMMANDS: dhcp client txoptions add Add an option. dhcp client txoptions list List all options. E-DOC-CTC-20060414-0002 v1.0...
Page 144: Dhcp Relay Add
DHCP Commands dhcp relay add Add an entry to the DHCP forward list. SYNTAX: dhcp relay add name = <string> where: name The forward entry name. REQUIRED RELATED COMMANDS: dhcp relay delete Delete an entry from the DHCP forward list. dhcp relay list List the DHCP forward list.
Page 145: Dhcp Relay Debug Stats
DHCP Commands dhcp relay debug stats Show the DHCP relay statistics. SYNTAX: dhcp relay debug stats EXAMPLE: =>dhcp relay debug stats DHCP relay statistics ------------------------- Client packet relayed Server packet relayed Bogus relay agent Bogus giaddr recv Corrupt agent option Missing agent option Bad circuit id Missing circuit id...
Page 146: Dhcp Relay Debug Traceconfig
DHCP Commands dhcp relay debug traceconfig Modify the DHCP relay trace configuration. SYNTAX: dhcp relay debug traceconfig [state = <{disabled | enabled}>] where: state Enable or disable tracing. OPTIONAL The default is disabled. EXAMPLE: =>dhcp relay debug traceconfig Tracing: disabled =>...
Page 147: Dhcp Relay Config
DHCP Commands dhcp relay config Set the DHCP relay configuration settings. SYNTAX: dhcp relay config [agentinfo = <{disabled | enabled}>] [agentmismatch = <{disabled | enabled}>] where: agentinfo Set the relay agent info status (RFC3046) enabled or disabled. OPTIONAL The default is disabled. agentmismatch Forward/drop DHCP reply packet when a relay agent info mismatch is OPTIONAL...
Page 148: Dhcp Relay Delete
DHCP Commands dhcp relay delete Delete an entry from the DHCP forward list. SYNTAX: dhcp relay delete name = <string> where: name The forward entry name. REQUIRED EXAMPLE: =>dhcp relay delete name = lan1_to_127.0.0.1 :dhcp relay delete name=lan1_to_127.0.0.1 => RELATED COMMANDS: dhcp relay add Add an entry to the DHCP forward list.
Page 149: Dhcp Relay Flush
DHCP Commands dhcp relay flush Flush the DHCP relay settings. The flush command does not impact previously saved configurations. SYNTAX: dhcp relay flush EXAMPLE: =>dhcp relay list DHCP server Interface giaddr ------------------------------------------------------- 127.0.0.1 eth0 192.168.1.254 =>dhcp relay flush =>dhcp relay list No dynamic interfaces defined.
Page 150: Dhcp Relay Ifconfig
DHCP Commands dhcp relay ifconfig Configure a DHCP relay interface. SYNTAX: dhcp relay ifconfig intf = <string> [relay = <{disabled | enabled}>] [maxhops = <number{0-16}>] [remoteid = <password>] [trusted = <{disabled | enabled}>] where: intf The name of the dynamic interface to be configured. REQUIRED relay Set the relay status to enabled or disabled.
Page 151 DHCP Commands EXAMPLE: =>dhcp relay iflist eth0 : admin state = up oper state = up max hops = 4 trusted = disabled remote id = Internet_trigger : admin state = down oper state = down max hops = 4 trusted = disabled remote id = Internet :...
Page 152: Dhcp Relay Iflist
DHCP Commands dhcp relay iflist Show the configuration of the relay interfaces. SYNTAX: dhcp relay iflist [intf = <string>] where: intf The name of the dynamic interface to be listed. OPTIONAL Note If not specified, all the relay interfaces will be shown. EXAMPLE: =>dhcp relay iflist eth0 :...
Page 153: Dhcp Relay List
DHCP Commands dhcp relay list List the DHCP forward list. SYNTAX: dhcp relay list [name = <string>] where: name The forward entry name. OPTIONAL EXAMPLE: =>dhcp relay list DHCP server Interface giaddr ------------------------------------------------------- 127.0.0.1 eth0 10.0.0.138 => RELATED COMMANDS: dhcp relay add Add an entry to the DHCP forward list.
Page 154: Dhcp Relay Modify
DHCP Commands dhcp relay modify Modify an entry from the DHCP forward list. SYNTAX: dhcp relay modify name = <string> [addr = <ip-address>] [intf = <{None | guest1 | dmz1 | wan1 | lan1 | Internet}>] [giaddr = <ip-address>] [script = <>] where: name The forward entry name.
Page 155: Dhcp Relay Ruleadd
DHCP Commands dhcp relay ruleadd Add a selection rule to a DHCP forward entry. SYNTAX: dhcp relay ruleadd name = <string> [key = <{or | and}>] rulename = <string> where: name The name of the forward entry. REQUIRED The logical key of the selection rule. OPTIONAL The default is or.
Page 156: Dhcp Relay Ruledelete
DHCP Commands dhcp relay ruledelete Delete a selection rule from a DHCP forward entry. SYNTAX: dhcp relay ruledelete name = <string> rulename = <string> where: name The name of the forward entry. REQUIRED rulename The name of the DHCP selection rule. REQUIRED RELATED COMMANDS: dhcp relay ruleadd...
Page 157: Dhcp Rule Add
DHCP Commands dhcp rule add Add a rule for DHCP conditional selection. SYNTAX: dhcp rule add name = <string> type = <{vci | uci | mac}> vci [!]= <quoted string> uci [!]= <quoted string> [match = <{exactly|as_substring}>] mac [!]= <hardware-address with wildcard | ex: '00:9f:aa:*:*:*'>...
Page 158: Dhcp Rule Debug Traceconfig
DHCP Commands dhcp rule debug traceconfig Modify DHCP rule trace configuration. SYNTAX: dhcp rule debug traceconfig [state = {disabled | enabled}] where: state Set tracing to disabled or enabled. OPTIONAL The default is disabled. E-DOC-CTC-20060414-0002 v1.0...
Page 159: Dhcp Rule Delete
DHCP Commands dhcp rule delete Delete a DHCP rule. SYNTAX: dhcp rule delete name = <string> where: name The name of the DHCP rule. REQUIRED EXAMPLE: =>dhcp rule delete name = new :dhcp rule delete name=new => RELATED COMMANDS: dhcp rule add Add a rule for DHCP conditional selection.
Page 160: Dhcp Rule Flush
DHCP Commands dhcp rule flush Flush all DHCP rules. SYNTAX: dhcp rule flush EXAMPLE: =>dhcp rule list Name Value vci=test =>dhcp rule flush =>dhcp rule list Name Value => RELATED COMMANDS: dhcp rule add Add a rule for DHCP conditional selection. dhcp rule delete Delete a DHCP rule.
Page 161: Dhcp Rule List
DHCP Commands dhcp rule list List all DHCP rules. SYNTAX: dhcp rule list EXAMPLE: =>dhcp rule list Name Value vci=test => RELATED COMMANDS: dhcp rule add Add a rule for DHCP conditional selection. dhcp rule delete Delete a DHCP rule. dhcp rule flush Flush all DHCP rules.
Page 162: Dhcp Server Config
DHCP Commands dhcp server config Print the DHCP server configuration settings. SYNTAX: dhcp server config [state = <{disabled | enabled}>] where: E-DOC-CTC-20060414-0002 v1.0...
Page 163: Dhcp Server Flush
DHCP Commands dhcp server flush Flush all DHCP server pool and lease entries. The flush command does not impact previously saved configurations. SYNTAX: dhcp server flush E-DOC-CTC-20060414-0002 v1.0...
Page 164: Dhcp Server Policy
DHCP Commands dhcp server policy Print the DHCP server policy settings. SYNTAX: dhcp server policy [verifyfirst = <disabled | enabled>] [trustclient = <disabled | enabled>] where: E-DOC-CTC-20060414-0002 v1.0...
Page 165: Dhcp Server Debug Clear
DHCP Commands dhcp server debug clear Clear the DHCP server statistics. SYNTAX: dhcp server debug clear EXAMPLE: =>dhcp server debug stats DHCP server state: Running DHCP server statistics: Corrupted packet recv DISCOVER 2451 REQUEST DECLINE RELEASE INFORM Pure BOOTP REQUESTS Other message types OFFERs sent 2451...
Page 166: Dhcp Server Debug Stats
DHCP Commands dhcp server debug stats Show the DHCP server statistics. SYNTAX: dhcp server debug stats EXAMPLE: =>dhcp server stats DHCP Server State: Stopped DHCP server statistics: Corrupted packet recv DISCOVER 2451 REQUEST DECLINE RELEASE INFORM Pure BOOTP REQUESTS Other message types OFFERs sent 2451 ACKs sent...
Page 167 DHCP Commands Second DHCP server seen: whether a concurrent DHCP server was found disabled the LAN or not. RELATED COMMANDS: dhcp server debug clear Clear the DHCP server statistics. E-DOC-CTC-20060414-0002 v1.0...
Page 168: Dhcp Server Debug Traceconfig
DHCP Commands dhcp server debug traceconfig Modify the DHCP server trace configuration. SYNTAX: dhcp server debug traceconfig [state = <{disabled | enabled}>] where: state Enable or disable tracing. OPTIONAL The default is disabled. EXAMPLE: =>dhcp server debug traceconfig Tracing: disabled =>...
Page 169: Dhcp Server Lease Add
DHCP Commands dhcp server lease add Add a DHCP server lease. SYNTAX: dhcp server lease add clientid = <client-id> pool = <string> [addr = <ip-address>] [offset = <number>] [leasetime = <number>] [expirytime = <number>] [gateway = <ip-address>] [macaddr = <hardware-address>] where: clientid The DHCP client identification string of the booting host.
Page 170 DHCP Commands RELATED COMMANDS: dhcp server lease delete Delete a DHCP server lease. dhcp server lease list List all the DHCP server leases. E-DOC-CTC-20060414-0002 v1.0...
Page 171: Dhcp Server Lease Delete
DHCP Commands dhcp server lease delete Delete a DHCP server lease. SYNTAX: dhcp server lease delete [clientid = <clientid | none>] [index = <number>] where: clientid The DHCP client identification string of the DHCP lease. OPTIONAL Note If not specified, all DHCP clients are deleted. index The DHCP server lease table index.
Page 172: Dhcp Server Lease Flush
DHCP Commands dhcp server lease flush Flush all the DHCP server leases. The flush command does not impact previously saved configurations. SYNTAX: dhcp server lease flush [pool = <string>] where: pool The name of the DHCP server pool to be flushed. OPTIONAL Only the leases belonging to this pool will be deleted.
Page 173: Dhcp Server Lease List
DHCP Commands dhcp server lease list List all the DHCP server leases. SYNTAX: dhcp server lease list [clientid = <clientid | none>] [index = <number>] where: clientid The DHCP client identification string of the DHCP lease. OPTIONAL Note If not specified, the DSHCP server leases for all the DHCP clients are listed. index The DHCP server lease table index.
Page 174: Dhcp Server Option Flush
DHCP Commands dhcp server option flush Flush all DHCP server option templates and instances. The flush command does not impact previously saved configurations. SYNTAX: dhcp server option flush E-DOC-CTC-20060414-0002 v1.0...
Page 175: Dhcp Server Option Instadd
DHCP Commands dhcp server option instadd Add a DHCP server option instance. SYNTAX: dhcp server option instadd name = <string> tmplname = <string> value = <Value : (type)value; type being 8-bit, 16-bit, 32-bit, addr, ascii, byte_array> where: name The name of the DHCP server option instance. REQUIRED tmplname The name of the DHCP server option template.
Page 176: Dhcp Server Option Instdelete
DHCP Commands dhcp server option instdelete Delete a DHCP server option instance. SYNTAX: dhcp server option instdelete name = <string> where: name The name of the DHCP server option instance to be deleted. REQUIRED EXAMPLE: =>dhcp server option instlist yourInstance Tmpl name : yourTmpl Value : (ascii)&#33...
Page 177: Dhcp Server Option Instlist
DHCP Commands dhcp server option instlist List all the DHCP server option instances. SYNTAX: dhcp server option instlist EXAMPLE: =>dhcp server option instlist yourInstance Tmpl name : yourTmpl Value : (ascii)&#33 myInstance Tmpl name : myTmpl Value : (32-bit)64 => RELATED COMMANDS: dhcp server option instadd Add a DHCP server option instance.
Page 178: Dhcp Server Option Tmpladd
DHCP Commands dhcp server option tmpladd Add a DHCP server option template. SYNTAX: dhcp server option tmpladd name = <string> optionid = <number{1-254}> type = <{8-bit | 16-bit | 32-bit | addr | ascii | byte_array}> where: name The name of the DHCP server option template. REQUIRED optionid A number between 1 and 254.
Page 179: Dhcp Server Option Tmpldelete
DHCP Commands dhcp server option tmpldelete Delete a DHCP server option template. SYNTAX: dhcp server option tmpldelete name = <string> where: name The name of the DHCP server option template to be deleted. REQUIRED EXAMPLE: =>dhcp server option tmpllist Name Option Type yourTmpl...
Page 180: Dhcp Server Option Tmpllist
DHCP Commands dhcp server option tmpllist List all the DHCP server option templates. SYNTAX: dhcp server option tmpllist EXAMPLE: =>dhcp server option tmpllist Name Option Type yourTmpl ascii myTmpl 32-bit => RELATED COMMANDS: dhcp server option tmpladd Add a DHCP server option template. dhcp server option tmpldelete Delete a DHCP server option template.
Page 181: Dhcp Server Pool Add
DHCP Commands dhcp server pool add Add a DHCP server pool. SYNTAX: dhcp server pool add name = <string> [index = <number>] where: name The name of the DHCP server pool. REQUIRED Note If not specified, the name is “dhcp_pool_x”, where x is a subsequent number.
Page 182: Dhcp Server Pool Config
The default value of this parameter is 0 (not specified), which means that the gateway IP address will be communicated by the remote server as soon as the PPP IPCP subnetmasking connection is established or that the SpeedTouch™ acts as the LAN default gateway.
Page 183 DNS server will be communicated by the remote server as soon as the PPP IPCP subnetmasking connection is established or that the SpeedTouch™ acts as the LAN DNS server. secdns The IP address of the optional secondary DNS server for DHCP clients.
Page 184: Dhcp Server Pool Delete
DHCP Commands dhcp server pool delete Delete a DHCP server pool. SYNTAX: dhcp server pool delete name = <string> where: name The name of the DHCP server pool to be deleted. REQUIRED Use the command :dhcp server pool list to obtain a list of all current DHCP leases.
Page 185: Dhcp Server Pool Flush
DHCP Commands dhcp server pool flush Flush all DHCP server pools. The flush command does not impact previously saved configurations. SYNTAX: dhcp server pool flush EXAMPLE: =>dhcp server pool list Pool Start Intf State 0 LAN_Private 10.0.0.1 10.0.0.254 eth0 USED 1 My_Pool 192.6.11.101 192.6.11.254...
Page 186: Dhcp Server Pool List
DHCP Commands dhcp server pool list List all DHCP server pools. SYNTAX: dhcp server pool list [name = <string>] where: name The name of the DHCP server pool to be shown. OPTIONAL Note If not specified, all the DHCP server pools are shown. EXAMPLE: =>dhcp server pool list Pool...
Page 187: Dhcp Server Pool Optadd
DHCP Commands dhcp server pool optadd Add an option instance to the DHCP server pool. SYNTAX: dhcp server pool optadd name = <string> instname = <string> where: name The name of the DHCP server pool to which an option instance must be added. REQUIRED instname The name of the DHCP server option instance.
Page 188: Dhcp Server Pool Optdelete
DHCP Commands dhcp server pool optdelete Delete an option instance from the DHCP server pool. SYNTAX: dhcp server pool optdelete name = <string> instname = <string> where: name The name of the DHCP server pool from which an option instance must be deleted. REQUIRED instname The name of the DHCP server option instance to be deleted.
Page 189: Dhcp Server Pool Rtadd
DHCP Commands dhcp server pool rtadd Add a route to the DHCP server pool. SYNTAX: dhcp server pool rtadd name = <string> dst = <ip-address> [dstmsk = <ip-mask(dotted or cidr)>] [gateway = <ipaddress | 0>] where: name The name of the DHCP server pool to which a route must be added. REQUIRED The IP destination address of the route for DHCP clients.
Page 190: Dhcp Server Pool Rtdelete
DHCP Commands dhcp server pool rtdelete Delete a route from the DHCP server pool. SYNTAX: dhcp server pool rtdelete name = <string> dst = <ip-address> [dstmsk = <ip-mask(dotted or cidr)>] [gateway = <ipaddress | 0>] where: name The name of the DHCP server pool from which a route must be deleted. REQUIRED The IP destination address of the route for DHCP clients.
Page 191: Dhcp Server Pool Ruleadd
DHCP Commands dhcp server pool ruleadd Add a selection rule to the DHCP server pool. SYNTAX: dhcp server pool ruleadd name = <string> [key = {or | and}] rulename = <string> where: name The name of the DHCP server pool to which a selection rule must be added. REQUIRED The logical key of the selection rule.
Page 192: Dhcp Server Pool Ruledelete
DHCP Commands dhcp server pool ruledelete Delete a selection rule from the DHCP server pool. SYNTAX: dhcp server pool ruleadd name = <string> rulename = <string> where: name The name of the DHCP server pool from which a selection rule must be deleted. REQUIRED rulename The name of the DHCP selection rule to be deleted.
Page 193: Dns Commands
DNS Commands DNS Commands Introduction This chapter describes the commands of the dns command group. Contents This chapter covers the following commands: dns client config Modify the Domain Name System (DNS) resolver configuration. dns client dnsadd Add a DNS server. dns client dnsdelete Delete a DNS server.
Page 194: Dns Client Config
DNS Commands dns client config Modify the Domain Name System (DNS) resolver configuration. SYNTAX: dns client config [timeout = <number{1-900}>] [retry = <number{0-10}>] [search = <{disabled | enabled}>] [list = <string>] [trace = <{disabled | enabled}>] where: timeout A number between 1 and 900 (seconds). OPTIONAL Represents the query timeout.
Page 195: Dns Client Dnsadd
DNS Commands dns client dnsadd Add a DNS server. SYNTAX: dns client dnsadd addr = <string> [port = <number>] where: addr The IP address of the DNS server to be added. REQUIRED port The DNS server port number. OPTIONAL The default is 53. EXAMPLE: =>dns client dnsadd addr=150.150.150.150 =>dns client dnslist...
Page 196: Dns Client Dnsdelete
DNS Commands dns client dnsdelete Delete a DNS server. SYNTAX: dns client dnsdelete index = <number{1-99}> where: index A number between 1 and 99. REQUIRED Represents the index number of the DNS server to be deleted. Use the command :dns client dnslist to obtain a list of DNS servers. EXAMPLE: =>dns client dnslist Entry...
Page 197: Dns Client Dnslist
DNS Commands dns client dnslist List all DNS servers. SYNTAX: dns client dnslist EXAMPLE: =>dns client dnslist Entry State Family Server CONNECTED [port] 53 - [addr] 127.0.0.1 CONNECTED [port] 53 - [addr] 150.150.150.150 => RELATED COMMANDS: dns client dnsadd Add a DNS server. dns client dnsdelete Delete a DNS server.
Page 198: Dns Client Flush
DNS Commands dns client flush Remove all DNS servers. SYNTAX: dns client flush E-DOC-CTC-20060414-0002 v1.0...
Page 199: Dns Client Nslookup
DNS Commands dns client nslookup DNS lookup for a domain name or an address. SYNTAX: dns client nslookup host = <string> where: host The DNS domain name string for which to query. REQUIRED E-DOC-CTC-20060414-0002 v1.0...
Page 200: Dns Server Config
DNS Commands dns server config Modify the DNS resolver configuration. SYNTAX: dns server config [domain = <string>] [timeout = <number{0-2147483647}>] [suppress = <number>] [state = <{disabled | enabled}>] [trace = <{disabled | enabled}>] [WANDownSpoofing = <{disabled | enabled}>] [WDSpoofedIP = <ip-address>] where: domain The DNS server domain name.
Page 201: Dns Server Flush
DNS Commands dns server flush Flush all local DNS hosts and routes. SYNTAX: dns server flush E-DOC-CTC-20060414-0002 v1.0...
Page 202: Dns Server Debug Clear
DNS Commands dns server debug clear Clear the DNS server/forwarder statistics. SYNTAX: dns server debug clear EXAMPLE: =>dns server debug stats Corrupted packets received Local questions resolved Local negative answers sent Total DNS packets forwarded External answers received Spoofed responses Forward table full, discard Spurious answers Unknown query types...
Page 203: Dns Server Debug Stats
DNS Commands dns server debug stats Print the DNS server/forwarder statistics. SYNTAX: dns server debug stats EXAMPLE: =>dns server debug stats Corrupted packets received Local questions resolved Local negative answers sent Total DNS packets forwarded External answers received Spoofed responses Forward table full, discard Spurious answers Unknown query types...
Page 204: Dns Server Debug Spoof Clear
DNS Commands dns server debug spoof clear Clear the intercept cache table SYNTAX: dns server debug spoof clear RELATED COMMANDS: dns server debug spoof Get the real ip for the given spoofed ip getaddress dns server debug spoof Get the error flags for the given spoofed ip getflags dns server debug spoof List the intercept cache table.
Page 205: Dns Server Debug Spoof Getaddress
DNS Commands dns server debug spoof getaddress Get the real ip for the given spoofed ip SYNTAX: dns server debug addr = <ip-address> spoof getaddress where: addr The IP address of the spoofed server. REQUIRED EXAMPLE: {Administrator}=>dns server debug spoof getaddress addr=198.18.1.1 :dns server debug spoof getaddress addr=198.18.1.1 Resolved ip = 0.0.0.0.
Page 206: Dns Server Debug Spoof Getflags
DNS Commands dns server debug spoof getflags Get the error flags for the given spoofed ip SYNTAX: dns server debug addr = <ip-address> spoof getflags where: addr The IP address of the spoofed server. REQUIRED EXAMPLE: {Administrator}[dns server debug spoof]=>:dns server debug spoof getflags addr = 192.168.1.254 :dns server debug spoof getflags addr=192.168.1.254 Invalid spoofed ip.
Page 207: Dns Server Debug Spoof List
DNS Commands dns server debug spoof list List the intercept cache table. SYNTAX: dsn server debug spoof list EXAMPLE: {Administrator}[dns server debug spoof]=>list Spoof IP FQDN Real IP Flags 198.18.1.1 eu.thmulti.com 0.0.0.0 Not resolved 198.18.1.2 thmulti.com 0.0.0.0 Not resolved 198.18.1.3 0.0.0.0 Not resolved 198.18.1.4...
Page 208: Dns Server Debug Spoof Update
DNS Commands dns server debug spoof update Update the intercept cache table. SYNTAX: dns server debug spoof update EXAMPLE: {Administrator}=>dns server debug spoof update {Administrator}=> RELATED COMMANDS: dns server debug spoof Clear the intercept cache table clear dns server debug spoof Get the real ip for the given spoofed ip getaddress dns server debug spoof...
Page 209: Dns Server Host Add
=>dns server host add name=myDNS addr=150.150.150.150 ttl=3600 =>dns server host list Address Hostname TTL (s) 150.150.150.150 myDNS 3600 <local> speedtouch <local> dsldevice => RELATED COMMANDS: dns server host delete Delete a local DNS host. dns server host list List all the local DNS hosts.
Page 210: Dns Server Host Delete
The name of the DNS host to be deleted. REQUIRED EXAMPLE: =>dns server host list Address Hostname TTL (s) 150.150.150.150 myDNS 3600 <local> speedtouch <local> dsldevice =>dns server host delete name=myDNS =>dns server host list Address Hostname TTL (s) <local> speedtouch <local>...
Page 211: Dns Server Host Flush
Flush all the local DNS hosts. SYNTAX: dns server host flush EXAMPLE: =>dns server host list Address Hostname TTL (s) 192.168.1.64 * Unknown-00-10-a4-ad-32-cf <local> dsldevice 1200 <local> speedtouch 1200 =>dns server host flush =>dns server host list => E-DOC-CTC-20060414-0002 v1.0...
Page 212: Dns Server Host List
=>dns server host list Address Hostname TTL (s) 192.168.1.64 * Unknown-00-10-a4-ad-32-cf <local> dsldevice 1200 <local> speedtouch 1200 => RELATED COMMANDS: dns server host add Add a local DNS host. dns server host delete Delete a local DNS host. E-DOC-CTC-20060414-0002 v1.0...
Page 213: Dns Server Route Add
DNS Commands dns server route add Adds a DNS forwarding route. SYNTAX: dns server route add dns = <ip-address> [src = <ip-address>] [srcmask = <ip-mask(dotted or cidr)>] [domain = <string>] [metric = <number{0-100}>] [intf = <string>] where: The IP address of a DNS server. REQUIRED The source IP address(es) using this remote DNS server.
Page 214: Dns Server Route Delete
DNS Commands dns server route delete Delete a DNS forwarding route. SYNTAX: dns server route delete dns = <ip-address> where: The IP address of the DNS server for which the forwarding route must be deleted. REQUIRED EXAMPLE: =>dns server route list DNS Server Source Domain...
Page 215: Dns Server Route Flush
DNS Commands dns server route flush Flush all DNS forwarding routes. SYNTAX: dns server route flush EXAMPLE: =>dns server route list DNS Server Source Domain Metric Intf State 150.150.150.150 10.0.0.0/8 myDNS eth0 =>dns server route flush =>dns server route list =>...
Page 216: Dns Server Route List
DNS Commands dns server route list List all the DNS forwarding routes. SYNTAX: dns server route list EXAMPLE: =>dns server route list DNS Server Source Domain Metric Intf State 150.150.150.150 10.0.0.0/8 myDNS eth0 => RELATED COMMANDS: dns server route add Adds a DNS forwarding route.
Page 217: Dsd Commands
DSD Commands DSD Commands Introduction This chapter describes the commands of the dsd command group. Contents This chapter covers the following commands: dsd config Display/modify the Differentiated Service Delivery (DSD) framework configuration. dsd debug config Display/modify DSD debug settings dsd debug connection list Display the internal connection pool usage.
Page 218: Dsd Config
DSD Commands dsd config Display/modify the Differentiated Service Delivery (DSD) framework configuration. SYNTAX: dsd config [state = <{disabled | enabled | automatic}>] where: state Choose between: OPTIONAL automatic (default): By default (DSD config state is automatic), the DSD framework is not active, for example no URL filtering or web site filtering is applied.
Page 219: Dsd Debug Config
DSD Commands dsd debug config Display/modify DSD debug settings SYNTAX: config [turbomode = <{disabled|enabled}>] where: turbomode Enable/disable turbomode OPTIONAL E-DOC-CTC-20060414-0002 v1.0...
Page 220: Dsd Debug Connection List
DSD Commands dsd debug connection list Display the internal connection pool usage. SYNTAX: dsd debug connection list [expand = <{disabled|enabled}>] where: expand Enable or disable the expanded listing. optional The default is disabled. E-DOC-CTC-20060414-0002 v1.0...
Page 221: Dsd Debug Proxy
DSD Commands dsd debug proxy Display/modify the HyperText Transfer Protocol (HTTP) Intercept fixed proxy configuration. SYNTAX: dsd debug proxy [state = <{disabled | enabled}>] [dest = <ip-address>] [port = <{supported TCP/UDP port} or number>] where: state Enable or disable fixed proxy redirecting. OPTIONAL The default is disabled.
Page 222: Dsd Debug Recycling
DSD Commands dsd debug recycling Display/modify HTTPI recycling settings SYNTAX: dsd debug recycling state = <disabled>|<enabled> interval = <number> httpidle = <number> otheridle = <number> where: state Enable/disable stream recycling OPTIONAL interval Time between successive activity checks OPTIONAL httpidle Minimal idle count for recycling (filtered) http streams OPTIONAL otheridle Minimal idle count for recycling other streams...
Page 223: Dsd Debug Stats
DSD Commands dsd debug stats Display/clear DSD framework and module statistics SYNTAX: dsd debug stats name = <{intercept|urlfilter|recycling|syslog|all} clear = <{no|yes}> where: name Specify the name of a module REQUIRED clear Clear the specified statistics REQUIRED E-DOC-CTC-20060414-0002 v1.0...
Page 224: Dsd Intercept Config
DSD Commands dsd intercept config Display/modify the HTTP Intercept configuration. SYNTAX: dsd intercept config [WDSpoofedIP = <ip-address>] [servertimeout = <number>] [servererrorurl = <string>] [categoryerrorurl = <string>] [monitorintercepturl = <string>] [urlblockedurl = <string>] [imageredirect = <{disabled | enabled}>] [imageredirecturl = <string>] [alwaysuseip = <{disabled | enabled}>] where: WDSpoofedIP...
Page 225: Dsd Syslog Config
DSD Commands dsd syslog config Display/modify the HTTP Intercept logging configuration. SYNTAX: dsd syslog config [syslog = <{none | unauthorized | errors | intercepted | all}>] where: syslog Define the type of events to log. OPTIONAL Choose between: none: nothing is logged to syslog. unauthorized: only the HTTP requests that are blocked because of a LocalRule, BlockCategory, BlockIPAddress or BlockObscure event, are logged.
Page 226: Dsd Syslog List
DSD Commands dsd syslog list Display the HTTP Intercept log file. SYNTAX: dsd syslog list EXAMPLE: =>dsd syslog list <86> SysUpTime: 00:22:37 [HTTPI] src=10.0.0.1 src_port=1965 dst=141.11.196.35 dst_port=80 event=Se rverConnect dst_name=aWebsite.com/icons/Button_Document.gif <86> SysUpTime: 00:22:59 [HTTPI] src=10.0.0.1 src_port=1968 dst=141.11.234.60 dst_port=80 event=Se rverConnect dst_name=anotherWebsite.com/rawgen.asp =>...
Page 227: Dsd Urlfilter Config
DSD Commands dsd urlfilter config Display/modify the URL filtering configuration. SYNTAX: dsd urlfilter config [state = <{disabled | enabled}>] [blockproxy = <{disabled | enabled}>] [blockipaddress = <{disabled | enabled}>] [blockobscuredip = <{disabled | enabled}>] [defaultaction = <{block | accept}>] where: state Enable or disable URL filtering.
Page 228: Dsd Urlfilter Rule Add
Choose between: block accept redirect. redirect The redirection URL. REQUIRED Note This parameter is only required when the action is redirect. EXAMPLE: =>dsd urlfilter rule add url=www.speedtouch.com action=redirect redirect=www.speedtouch.be =>dsd urlfilter rule list Index Action Redirect ----- ------ -------- redirect www.speedtouch.com www.speedtouch.be...
Page 229: Dsd Urlfilter Rule Delete
OPTIONAL EXAMPLE: =>dsd urlfilter rule list Index Action Redirect ----- ------ -------- redirect www.speedtouch.com www.speedtouch.be accept www.baen.com Rule list statistics : 2 present, 128 total (0.0% used) =>dsd urlfilter rule delete index=1 =>dsd urlfilter rule list Index Action Redirect -----...
Page 230: Dsd Urlfilter Rule Flush
EXAMPLE: =>dsd urlfilter rule list Index Action Redirect ----- ------ -------- redirect www.speedtouch.com www.speedtouch.be accept www.baen.com Rule list statistics : 2 present, 128 total (0.0% used) =>dsd urlfilter rule flush =>dsd urlfilter rule list Index Action Redirect...
Page 231: Dsd Urlfilter Rule List
EXAMPLE: =>dsd urlfilter rule list Index Action Redirect ----- ------ -------- redirect www.speedtouch.com www.speedtouch.be accept www.baen.com Rule list statistics : 2 present, 128 total (0.0% used) => RELATED COMMANDS: dsd urlfilter rule add Add a rule. dsd urlfilter rule delete Delete a rule.
Page 232: Dsd Urlfilter Rule Modify
Redirect ----- ------ -------- redirect www.speedtouch.com www.speedtouch.be accept www.baen.com Rule list statistics : 2 present, 128 total (0.0% used) =>dsd urlfilter rule modify index=0 newurl=www.speed*.* action=redirect redirect=www.speedtouch.be =>dsd urlfilter rule list Index Action Redirect ----- ------ -------- redirect www.speed*.* www.speedtouch.be accept www.baen.com...
Page 233: Dyndns Commands
DynDNS Commands DynDNS Commands Introduction Dynamic DNS is a service that allows to bind a host name to an IP address. In contrast to classical DNS, this service allows regular updates of the IP address related to a host name. In this way, hosts of which the IP address regularly changes (for example due to a limited DHCP lease time) can be identified by a static host name that is unique throughout the Internet.
Page 234: Dyndns Add
DynDNS Commands dyndns add Add a dynamic DNS client. SYNTAX: dyndns add name = <string> where: name The name of the new dynamic DNS client. REQUIRED Note A maximum of 5 clients can be configured. EXAMPLE: =>dyndns add name=WAN =>dyndns list [INIT] user = password =...
Page 235: Dyndns Delete
DynDNS Commands dyndns delete Delete a dynamic DNS client. SYNTAX: dyndns delete name = <string> where: name The name of the dynamic DNS client to be deleted. REQUIRED EXAMPLE: =>dyndns list [INIT] user = password = addr = 0.0.0.0 =>dyndns delete name=WAN =>dyndns list =>...
Page 236: Dyndns Flush
DynDNS Commands dyndns flush Delete all the dynamic DNS clients. SYNTAX: dyndns flush E-DOC-CTC-20060414-0002 v1.0...
Page 237: Dyndns List
DynDNS Commands dyndns list List all the dynamic DNS clients. SYNTAX: dyndns list EXAMPLE: =>dyndns list [INIT] user = password = addr = 0.0.0.0 => RELATED COMMANDS: dyndns add Add a dynamic DNS client. dyndns delete Delete a dynamic DNS client. E-DOC-CTC-20060414-0002 v1.0...
Page 238: Dyndns Modify
DynDNS Commands dyndns modify Modify a dynamic DNS client. SYNTAX: dyndns modify name = <string> [intf = <string>] [user = <string>] [password = <password>] [group = <string>] [mx = <string>] [backmx = <{disabled | enabled}>] [wildcard = <{disabled | enabled}>] [offline = <{disabled | enabled}>] [service = <{dyndns | statdns | custom | No-IP | DtDNS | gnudip}>]...
Page 239 DynDNS Commands EXAMPLE: =>dyndns list [INIT] user = password = addr = 0.0.0.0 =>dyndns modify name=WAN intf=RtPPPoE user=DNSuser password=_DEV_BA8C0C963BD84130 service=gnudip =>dyndns list : RtPPPoE_ppp [INIT] options = gnudip user = my_DNS_user password = ******** addr = 0.0.0.0 => E-DOC-CTC-20060414-0002 v1.0...
Page 240: Dyndns Host Add
DynDNS Commands dyndns host add Add a fully qualified host name. SYNTAX: dyndns host add group = <string> name = <string> where: group The dynamic DNS host group. REQUIRED Note A maximum of 4 different groups can be created. name The name of an IP host to add.
Page 241: Dyndns Host Delete
DynDNS Commands dyndns host delete Delete a host name. SYNTAX: dyndns host delete name = <string> where: name The name of the IP host to be deleted. REQUIRED EXAMPLE: =>dyndns host list local : [ ] localhost.com public : [ ] publichost.com legend : not initialised update in progress...
Page 242: Dyndns Host Flush
DynDNS Commands dyndns host flush Delete all hosts. The hosts cannot be flushed, if there is still a group referenced to the hosts. SYNTAX: dyndns host flush E-DOC-CTC-20060414-0002 v1.0...
Page 243: Dyndns Host List
DynDNS Commands dyndns host list List all host names. SYNTAX: dyndns host list EXAMPLE: =>dyndns host list local : [ ] localhost.com public : [ ] publichost.com legend : not initialised update in progress update successful error => RELATED COMMANDS: dyndns host add Add a fully qualified host name.
Page 244: Dyndns Service List
DynDNS Commands dyndns service list List all dynamic DNS services. SYNTAX: dyndns service list EXAMPLE: =>dyndns service list dyndns server = members.dyndns.org port = 80 request = /nic/update update interval = 2097120 retry interval = 30 max retry statdns server = members.dyndns.org port = 80...
Page 245: Dyndns Service Modify
DynDNS Commands dyndns service modify Modify specific dynamic DNS service settings. SYNTAX: dyndns service modify name = <string> [server = <string>] [port = <{supported TCP/UDP port name} or number>] [request = <string>] [updateinterval = <number{0-2097120}>] [retryinterval = <number{0-600}] [max_retry = <number{1-5}>] where: name The name of the dynamic DNS service.
Page 246 DynDNS Commands EXAMPLE: =>dyndns service modify name=custom server=mydyndns.org port=www-http request=hereiam updateinterval=2000000 retryinterval=15 max_retry=5 =>dyndns service list dyndns server = members.dyndns.org port = 80 request = /nic/update update interval = 2097120 retry interval = 30 max retry statdns server = members.dyndns.org port = 80 request...
Page 247: Env Commands
Env Commands Env Commands Introduction This chapter describes the commands of the env command group. Contents This chapter covers the following commands: env flush Flush all the non-system environment variables. env get Get the current value of an environment variable. env list Show all the currently available environment variables.
Page 248: Env Flush
Env Commands env flush Flush all the non-system environment variables. SYNTAX: env flush E-DOC-CTC-20060414-0002 v1.0...
Page 249: Env Get
= <string> where: The name of the environment variable. REQUIRED Use the command :env list to obtain a list of all environment variables. EXAMPLE: =>env get var=_PROD_FRIENDLY_NAME SpeedTouch v1.0 => RELATED COMMANDS: env list List all current environment variables. E-DOC-CTC-20060414-0002 v1.0...
Page 250: Env List
Env Commands env list Show all the currently available environment variables. SYNTAX: env list RELATED COMMANDS: env get Get the current value of an environment variable. E-DOC-CTC-20060414-0002 v1.0...
Page 251: Env Set
Env Commands env set Set an environment variable. SYNTAX: env set var = <string> value = <translated string> where: The name of the environment variable. REQUIRED When creating an environment variable, any name is allowed. However spaces are NOT allowed and the name may NOT start with: “CONF”...
Page 252: Env Unset
The name of the environment variable to be deleted. REQUIRED Note System variables (built-in variables with names starting with an underscore “_”, “CONF” or “HOST”) cannot be unset, changed or deleted. EXAMPLE: =>env list _COMPANY_NAME=THOMSON multimedia _COMPANY_URL=http://www.speedtouch.com _PROD_NAME=SpeedTouch ..CONF_DATE=March 2004 CONF_REGION=World HOST_SETUP=user =>env unset var=CONF_REGION =>env list _COMPANY_NAME=THOMSON multimedia _COMPANY_URL=http://www.speedtouch.com...
Page 253: Eth Commands
Eth Commands Eth Commands Introduction This chapter describes the commands of the eth command group. Contents This chapter covers the following commands: eth ifadd Create a new ETH interface. eth ifattach Attach an ETH interface. eth ifconfig Modify an ETH interface. eth ifdelete Delete an ETH interface.
Page 254 Eth Commands eth bridge vlan ifdelete Delete a bridge interface from a VLAN. eth bridge vlan iflist Display all VLANs. eth device ifconfig Configure an Ethernet interface. eth device iflist Show status of Ethernet interfaces. eth switch group flush Set all the ports to the default settings. eth switch group list List all the configured switch groups.
Page 255: Eth Ifadd
Eth Commands eth ifadd Create a new ETH interface. SYNTAX: eth ifadd intf = <string> where: intf The name of the new ETH interface. REQUIRED RELATED COMMANDS: eth ifdelete Delete an ETH interface. eth iflist Display the ETH interfaces. E-DOC-CTC-20060414-0002 v1.0...
Page 256: Eth Ifattach
Eth Commands eth ifattach Attach an ETH interface. SYNTAX: eth ifattach intf = <string> where: intf The name of the ETH interface to be attached. REQUIRED RELATED COMMANDS: eth ifdetach Detach an ETH interface. E-DOC-CTC-20060414-0002 v1.0...
Page 257: Eth Ifconfig
Eth Commands eth ifconfig Modify an ETH interface. SYNTAX: eth ifconfig intf = <string> [dest = <string>] [retry = <number{0-65535}>] [vlan = <string>] where: intf The name of the ETH interface to be configured. REQUIRED dest The destination interface for this ETH interface. OPTIONAL retry A number between 0 and 65535.
Page 258: Eth Ifdelete
Eth Commands eth ifdelete Delete an ETH interface. SYNTAX: eth ifdelete intf = <string> where: intf The name of the ETH interface name to be deleted. REQUIRED RELATED COMMANDS: eth ifadd Create a new ETH interface. eth iflist Display the ETH interfaces. E-DOC-CTC-20060414-0002 v1.0...
Page 259: Eth Ifdetach
Eth Commands eth ifdetach Detach an ETH interface. SYNTAX: eth ifdetach intf = <string> where: intf The name of the ETH interface to be detached. REQUIRED RELATED COMMANDS: eth ifattach Attach an ETH interface. E-DOC-CTC-20060414-0002 v1.0...
Page 260: Eth Iflist
Eth Commands eth iflist Display the ETH interfaces. SYNTAX: eth iflist [intf = <string>] where: intf The name of the ETH interface to be displayed. OPTIONAL Note If not specified, all the ETH interfaces will be displayed. RELATED COMMANDS: eth ifadd Create a new ETH interface.
Page 261: Eth Flush
Eth Commands eth flush Flush all the ETH interfaces. The flush command does not impact previously saved configurations. SYNTAX: eth flush E-DOC-CTC-20060414-0002 v1.0...
Page 262: Eth Bridge Clear
Eth Commands eth bridge clear Clear the bridge statistics. SYNTAX: eth bridge clear E-DOC-CTC-20060414-0002 v1.0...
Page 263: Eth Bridge Config
The bridge filter to be applied for all Wide Area Network (WAN) bridge ports. OPTIONAL Choose between: no_WAN_broadcast: broadcasts from the SpeedTouch™ itself to the WAN are filtered out, broadcasts from the LAN to the WAN are still passed through none: no broadcasts are filtered out.
Page 264: Eth Bridge Dynvlan Actlist
Eth Commands eth bridge dynvlan actlist Display the active MAC entries for the dynamic VLAN membership. SYNTAX: eth bridge dynvlan actlist RELATED COMMANDS: eth bridge dynvlan add Add a dynamic VLAN membership entry. eth bridge dynvlan Modify the dynamic VLAN membership configuration. config eth bridge dynvlan Delete a dynamic VLAN membership entry.
Page 265: Eth Bridge Dynvlan Add
Eth Commands eth bridge dynvlan add Add a dynamic VLAN membership entry. SYNTAX: eth bridge dynvlan add [id = <number{0-100000}>] hwaddr = <masked-hardware-address> vlan = <string> [remvlan = <{default}>] where: A number between 0 and 100000. OPTIONAL Represents the id of the dynamic VLAN membership entry. hwaddr The (masked) ethernet MAC address of the dynamic VLAN REQUIRED...
Page 266: Eth Bridge Dynvlan Config
Eth Commands eth bridge dynvlan config Modify the dynamic VLAN membership configuration. SYNTAX: eth bridge dynvlan config [timeout = <number{0-100000}>] where: timeout A number between 0 and 100000 (seconds). OPTIONAL Represents timeout for the dynamic entries. RELATED COMMANDS: eth bridge dynvlan Display the active MAC entries for the dynamic VLAN membership.
Page 267: Eth Bridge Dynvlan Delete
Eth Commands eth bridge dynvlan delete Delete a dynamic VLAN membership entry. SYNTAX: eth bridge dynvlan delete id = <number{0-100000}> where: A number between 0 and 100000. REQUIRED Represents the id of a dynamic VLAN membership. RELATED COMMANDS: eth bridge dynvlan Display the active MAC entries for the dynamic VLAN membership.
Page 268: Eth Bridge Dynvlan Flush
Eth Commands eth bridge dynvlan flush Flush all dynamic VLAN membership entries. SYNTAX: eth bridge dynvlan flush E-DOC-CTC-20060414-0002 v1.0...
Page 269: Eth Bridge Dynvlan List
Eth Commands eth bridge dynvlan list Display a dynamic VLAN membership entry. SYNTAX: eth bridge dynvlan list RELATED COMMANDS: eth bridge dynvlan Display the active MAC entries for the dynamic VLAN membership. actlist eth bridge dynvlan add Add a dynamic VLAN membership entry. eth bridge dynvlan Modify the dynamic VLAN membership configuration.
Page 270: Eth Bridge Flush
Eth Commands eth bridge flush Flush bridge interfaces and parameters. The flush command does not impact previously saved configurations. SYNTAX: eth bridge flush E-DOC-CTC-20060414-0002 v1.0...
Page 271: Eth Bridge Ifadd
Eth Commands eth bridge ifadd Create a new bridge interface. SYNTAX: eth bridge ifadd intf = <string> where: intf The name of the new bridge interface. REQUIRED RELATED COMMANDS: eth bridge ifdelete Delete a bridge interface. eth bridge iflist Display the current bridge interfaces. E-DOC-CTC-20060414-0002 v1.0...
Page 272: Eth Bridge Ifattach
Eth Commands eth bridge ifattach Attach a bridge interface. SYNTAX: eth bridge ifattach intf = <string> where: intf The name of the bridge interface to be attached. REQUIRED RELATED COMMANDS: eth bridge ifdetach Detach a bridge interface. E-DOC-CTC-20060414-0002 v1.0...
Page 273: Eth Bridge Ifconfig
The default is forwarding. retry A number between 0 and 65535. OPTIONAL Represents the number of times the SpeedTouch™ retries to set up a WAN connection before giving up. The default is 10. vlan Select the default VLAN. OPTIONAL prioconfig The priority configuration for this interface.
Page 274 Eth Commands regenprio The priority regeneration table for tagged ingress packets. OPTIONAL The default is 01234567. ingressfiltering Enable/disable discard of tagged ingress packets if the interface is not part of OPTIONAL the VLAN. The default is disabled. acceptvlanonly Enable or disable receipt of tagged ingress packets. OPTIONAL The default is disabled.
Page 275: Eth Bridge Ifdelete
Eth Commands eth bridge ifdelete Delete a bridge interface. SYNTAX: eth bridge ifdelete intf = <string> where: intf The name of the bridge interface name to be deleted. REQUIRED RELATED COMMANDS: eth bridge ifadd Create a new bridge interface. eth bridge iflist Display the current bridge interfaces.
Page 276: Eth Bridge Ifdetach
Eth Commands eth bridge ifdetach Detach a bridge interface. SYNTAX: eth bridge ifdetach intf = <string> where: intf The name of the bridge interface to be detached. REQUIRED RELATED COMMANDS: eth bridge ifattach Attach a bridge interface. E-DOC-CTC-20060414-0002 v1.0...
Page 277: Eth Bridge Iflist
Eth Commands eth bridge iflist Display the current bridge interfaces. SYNTAX: eth bridge iflist [intf = <string>] where: intf The name of the bridge interface to be displayed. OPTIONAL Note If not specified, all bridge interfaces are shown. RELATED COMMANDS: eth bridge ifadd Create a new bridge interface.
Page 278: Eth Bridge Macadd
Eth Commands eth bridge macadd Add a static MAC address to a bridge interface. This command allows to manually add static MAC addresses, which should normally be dynamically discovered by the bridge itself. SYNTAX: eth bridge macadd intf = <string> hwaddr = <hardware-address>...
Page 279: Eth Bridge Macdelete
Eth Commands eth bridge macdelete Remove a MAC address from the filtering database. SYNTAX: eth bridge macdelete hwaddr = <hardware-address> [vlan = <string>] where: hwaddr The Ethernet MAC address of the entry to be deleted. REQUIRED vlan The VLAN. OPTIONAL EXAMPLE: =>eth bridge maclist 00:0d:9d:47:dd:aa -- dynamic, ethport1...
Page 280: Eth Bridge Maclist
Eth Commands eth bridge maclist Display the MAC address database. SYNTAX: eth bridge maclist EXAMPLE: =>eth bridge maclist 00:0d:9d:47:dd:aa -- dynamic, ethport1, 300 seconds 00:90:d0:72:88:64 -- permanent 01:00:5e:00:00:67 -- static 01:00:5e:7f:ff:fa -- static 01:80:c2:00:00:00 -- permanent 01:80:c2:00:00:01 -- permanent 01:80:c2:00:00:02 -- permanent 01:80:c2:00:00:03 -- permanent 01:80:c2:00:00:04 -- permanent 01:80:c2:00:00:05 -- permanent...
Page 281: Eth Bridge Mcdadd
Eth Commands eth bridge mcdadd Add a multicast group to be dropped to the database. SYNTAX: eth bridge mcdadd srcintfs = <string or combination of strings separated by '+'}> dstintfs = <string or combination of strings separated by '+'}> where: srcports The source bridge interfaces from which multicast packets must be dropped.
Page 282: Eth Bridge Mcddelete
Eth Commands eth bridge mcddelete Delete a multicast group to be dropped from the database. SYNTAX: eth bridge mcddelete RELATED COMMANDS: eth bridge mcdadd Add a multicast group to be dropped to the database. eth bridge mcdlist Display the multicast group to be dropped from the database. E-DOC-CTC-20060414-0002 v1.0...
Page 283: Eth Bridge Mcdlist
Eth Commands eth bridge mcdlist Display the multicast group to be dropped from the database. SYNTAX: eth bridge mcdlist RELATED COMMANDS: eth bridge mcdadd Add a multicast group to be dropped to the database. eth bridge mcddelete Delete a multicast group to be dropped from the database. E-DOC-CTC-20060414-0002 v1.0...
Page 284: Eth Bridge Rule Add
Eth Commands eth bridge rule add Add a new constraint to the VLAN learning system. SYNTAX: eth bridge rule add type = <{shared | independent}> vlan = <string> [vlan2 = <string>] [isi = <number{0-32}>] where: type Type of constraint. REQUIRED Choose between: shared independent.
Page 285: Eth Bridge Rule Delete
Eth Commands eth bridge rule delete Delete a constraint from the VLAN learning system. SYNTAX: eth bridge rule delete index = <number{0-32}> where: index Index of the constraint to be deleted. REQUIRED Use the command :eth bridge rule list to obtain a list of the indexes of the constraints.
Page 286: Eth Bridge Rule Flush
Eth Commands eth bridge rule flush Flush all constraints from the VLAN learning system. SYNTAX: eth bridge rule flush E-DOC-CTC-20060414-0002 v1.0...
Page 287: Eth Bridge Rule List
Eth Commands eth bridge rule list Display all constraints from the VLAN learning system. SYNTAX: eth bridge rule list EXAMPLE: =>eth bridge rule list Index Type VLAN Parameter ----- ---- ---- --------- independant default Independent set identifier: 1 => RELATED COMMANDS: eth bridge rule add Add a new constraint to the VLAN learning system.
Page 288: Eth Bridge Vlan Ifadd
Eth Commands eth bridge vlan ifadd Add a bridge interface to a VLAN. SYNTAX: eth bridge vlan ifadd name = <string> intf = <string> [untagged = <{disabled | enabled}>] where: name The VLAN name to which a bridge interface must be added. REQUIRED intf The name of the bridge interface to be added to the VLAN.
Page 289: Eth Bridge Vlan Ifconfig
Eth Commands eth bridge vlan ifconfig Modify a bridge interface from a VLAN. SYNTAX: eth bridge vlan ifconfig name = <string> intf = <string> untagged = <{disabled | enabled}> where: name The VLAN name for which a bridge interface must be modified. REQUIRED intf The name of the bridge interface to be modified.
Page 290: Eth Bridge Vlan Ifdelete
Eth Commands eth bridge vlan ifdelete Delete a bridge interface from a VLAN. SYNTAX: eth bridge vlan ifdelete name = <string> intf = <string> where: name The VLAN name for which a bridge interface must be deleted. REQUIRED intf The name of the bridge interface to be deleted. REQUIRED RELATED COMMANDS: eth bridge vlan ifadd...
Page 291: Eth Bridge Vlan Iflist
Eth Commands eth bridge vlan iflist Display all VLANs. SYNTAX: eth bridge vlan iflist RELATED COMMANDS: eth bridge vlan ifadd Add a bridge interface to a VLAN. eth bridge vlan ifconfig Modify a bridge interface from a VLAN. eth bridge vlan ifdelete Delete a bridge interface from a VLAN.
Page 292: Eth Device Ifconfig
Eth Commands eth device ifconfig Configure an Ethernet interface. SYNTAX: eth device ifconfig intf = <string> [type = <{auto | 10BaseTHD | 10BaseTFD | 100BaseTHD | 100BaseTFD} or number>] [state = <{enabled | disabled}>] where: intf The name of a physical interface. REQUIRED type The Ethernet type.
Page 293: Eth Device Iflist
Eth Commands eth device iflist Show status of Ethernet interfaces. SYNTAX: eth device iflist EXAMPLE: =>eth device iflist Interface Type Result State ethif1 auto 100BaseTFD UP [forwarding] ethif2 auto 100BaseTFD UP [forwarding] ethif3 auto 100BaseTFD UP [forwarding] ethif4 auto 100BaseTFD UP [forwarding] usbif1 UP [forwarding]...
Page 294: Eth Switch Group Flush
Eth Commands eth switch group flush Set all the ports to the default settings. All the ports are placed in group 0. SYNTAX: eth switch group flush EXAMPLE: =>eth switch group list Group 0 Ports: 4 Group 1 Ports: 1 Group 2 Ports: 2 3 =>eth switch group flush =>eth switch group list...
Page 295: Eth Switch Group List
Eth Commands eth switch group list List all the configured switch groups. SYNTAX: eth switch group list EXAMPLE: =>eth switch group list Group 0 Ports: 4 Group 1 Ports: 1 Group 2 Ports: 2 3 => RELATED COMMANDS: eth switch group move Move a specified port to a specified switch group.
Page 296: Eth Switch Group Move
Eth Commands eth switch group move Move a specified port to a specified switch group. SYNTAX: eth switch group move group = <number{0-3}> port = <number{1-4}> where: group A number between 0 and 4. REQUIRED Represents the group ID to which the port must be moved. port A number between 01 and 4.
Page 297: Eth Switch Mirror Capture
Eth Commands eth switch mirror capture Define the specified port to be the Mirror Capture Port. Only one port can be the Mirror Capture Port at any one time. SYNTAX: eth switch mirror capture port = <number{1-4}> where: port The port to be the Mirror Capture Port. REQUIRED Note If no port number is specified, then the port number of the Mirror Capture Port...
Page 298: Eth Switch Mirror Egress
Eth Commands eth switch mirror egress Enable or disable the specified port to be the Mirror Egress Port. Only one port can be the Mirror Egress Port at any one time. But a port can be the Mirror Egress Port and the Mirror Ingress Port at the same time. SYNTAX: eth switch mirror egress port = <number{1-4}>...
Page 299: Eth Switch Mirror Ingress
Eth Commands eth switch mirror ingress Enable or disable the specified port to be the Mirror Ingress Port. Only one port can be the Mirror Ingress Port at any one time. But a port can be the Mirror Egress Port and the Mirror Ingress Port at the same time. SYNTAX: eth switch mirror ingress port = <number{1-4}>...
Page 300: Eth Switch Share Add
Eth Commands eth switch share add Add a port to be shared. SYNTAX: eth switch share add port = <number{1-4}> shared = <number{1-4}> where: port A number between 1 and 4. REQUIRED Represents the port. shared A number between 1 and 4. REQUIRED Represents the shared port.
Page 301: Eth Switch Share Delete
Eth Commands eth switch share delete Delete a shared port. SYNTAX: eth switch share delete port = <number{1-4}> shared = <number{1-4}> where: port A number between 1 and 4. REQUIRED Represents the port. shared A number between 1 and 4. REQUIRED Represents the shared port.
Page 302: Eth Switch Share List
Eth Commands eth switch share list Display shared ports. SYNTAX: eth switch share list RELATED COMMANDS: eth switch share add Add a port to be shared. eth switch share delete Delete a shared port. E-DOC-CTC-20060414-0002 v1.0...
Page 303: Eth Vlan Add
Eth Commands eth vlan add Add a new VLAN. SYNTAX: eth vlan add name = <string> vid = <number{2-4094}> [addrule = <{disabled | enabled}>] where: name The new VLAN name. REQUIRED A number representing the new VLAN ID. REQUIRED Note The ID 1 is reserved for the default VLAN.
Page 304: Eth Vlan Delete
Eth Commands eth vlan delete Delete a VLAN. SYNTAX: eth vlan delete name = <string> where: name The name of the VLAN to be deleted. REQUIRED EXAMPLE: =>eth vlan list Name ---- default myVLAN =>eth vlan delete name=myVLAN vid=2 =>eth vlan list Name ---- default...
Page 305: Eth Vlan Flush
Eth Commands eth vlan flush Flush all VLANs. All the VLANs, except the default VLAN will be flushed. SYNTAX: eth vlan flush EXAMPLE: =>eth vlan list Name ---- default myVLAN yourVLAN =>eth vlan flush =>eth vlan list Name ---- default =>...
Page 306: Eth Vlan List
Eth Commands eth vlan list Display all VLANs. SYNTAX: eth vlan list EXAMPLE: =>eth vlan list Name ---- default myVLAN => RELATED COMMANDS: eth vlan add Add a new VLAN. eth vlan delete Delete a VLAN. E-DOC-CTC-20060414-0002 v1.0...
Page 307: Expr Commands
Expr Commands Expr Commands Introduction This chapter describes the commands of the expr command group. Contents This chapter covers the following commands: expr add Add a subexpression to an expression. expr delete Delete an expression. expr flush Flush all the expressions. expr list List the expressions.
Page 308: Expr Add
Expr Commands expr add Add a subexpression to an expression. SYNTAX: expr add name = <string> type = <{intf | ip | serv}> addr [!]= <ip-range> [intf [!]= <string>] [intfgroup [!]= <{wan|local|lan|tunnel|dmz|guest} or number>] [tos [!]= <number{0-255}>] [precedence [!]= <IP precedence type> or <number>] [dscp [!]= <DSCP name>...
Page 309 Expr Commands A number between 0 and 255. OPTIONAL Represents the Type of Service (ToS) specification in the IP packet. Note The parameters tos, precedence dscp are mutually exclusive. precedence The precedence in the IP packet (part of tos). OPTIONAL Select an IP precedence (see “...
Page 310 Expr Commands EXAMPLE: =>expr list name type use flags expression ------------------------------------------------------------------------------------------ _myPPP_ppp intf 1. intf=myPPP_ppp _eth0 intf 1. intf=eth0 intf 1. intfgroup=0 intf 1. intfgroup=2 local intf 1. intfgroup=1 notwan intf 1. intfgroup=2 2. intfgroup=1 _10.0.0.138 1. addr=10.0.0.138 _192.168.1.254 1. addr=192.168.1.254 DiffServ serv 1.
Page 311: Expr Delete
Expr Commands expr delete Delete an expression. SYNTAX: expr delete name = <string> [index = <number>] where: name The name of the expression to be deleted. REQUIRED index The index of the subexpression to be deleted. OPTIONAL Note If not specified, all the subexpressions wil be deleted. E-DOC-CTC-20060414-0002 v1.0...
Page 312 Expr Commands EXAMPLE: =>expr list name type use flags expression ------------------------------------------------------------------------------------------ _myPPP_ppp intf 1. intf=myPPP_ppp _eth0 intf 1. intf=eth0 intf 1. intfgroup=0 intf 1. intfgroup=2 local intf 1. intfgroup=1 notwan intf 1. intfgroup=2 2. intfgroup=1 myEXPR intf 1. intf=Internet intfgroup=2 _10.0.0.138 1.
Page 313: Expr Flush
Expr Commands expr flush Flush all the expressions. SYNTAX: expr flush E-DOC-CTC-20060414-0002 v1.0...
Page 314: Expr List
Expr Commands expr list List the expressions. SYNTAX: expr list [name = <string>] [type = <{intf | ip | serv}>] [format = <{pretty | cli}>] where: name The name of an existing expression. OPTIONAL Note If not specified, all the expressions will be listed. type The expression type.
Page 315 Expr Commands EXAMPLE 1: E-DOC-CTC-20060414-0002 v1.0...
Page 316 Expr Commands =>expr list name type use flags expression ------------------------------------------------------------------------------------------ _Internet intf 1. intf=Internet _LocalNetwork intf 1. intf=LocalNetwork HTTPI_if_0 intf 1. intf=LocalNetwork 2. intf=LocalNetwork 3. intf=LocalNetwork HTTP_if_0 intf 1. intfgroup=2 HTTPs_if_0 intf 1. intfgroup=2 FTP_if_0 intf 1. intfgroup=2 TELNET_if_0 intf 1.
Page 317 Expr Commands EXAMPLE 2: E-DOC-CTC-20060414-0002 v1.0...
Page 318 Expr Commands =>expr list format=cli :expr add name=_Internet type=intf intf=Internet :expr add name=_LocalNetwork type=intf intf=LocalNetwork :expr add name=HTTPI_if_0 type=intf intf=LocalNetwork :expr add name=HTTPI_if_0 type=intf intf=LocalNetwork :expr add name=HTTPI_if_0 type=intf intf=LocalNetwork :expr add name=HTTP_if_0 type=intf intfgroup=lan :expr add name=HTTPs_if_0 type=intf intfgroup=lan :expr add name=FTP_if_0 type=intf intfgroup=lan :expr add name=TELNET_if_0 type=intf intfgroup=lan :expr add name=DNS-S_if_0 type=intf intfgroup=lan...
Page 319 Expr Commands RELATED COMMANDS: expr add Add a subexpression to an expression. expr delete Delete an expression. E-DOC-CTC-20060414-0002 v1.0...
Page 320: Expr Modify
Expr Commands expr modify Modify an expression. SYN TAX: expr modify name = <string> type = <{intf | ip | serv}> index = <number> addr [!]= <ip-range> [intf [!]= <string>] [intfgroup [!]= <{wan|local|lan|tunnel|dmz|guest} or number>] [bridgeport [!]= <number>] [tos [!]= <number{0-255}>] [precedence [!]= <IP precedence type>...
Page 321 Expr Commands intfgroup The IP interface group. OPTIONAL Choose between: local tunnel guest. Note Only for expression type intf. bridgeport The bridge port number. OPTIONAL Note Only for expression type intf. A number between 0 and 255. OPTIONAL Represents the ToS specification in the IP packet. Note The parameters tos, precedence...
Page 322 Expr Commands E-DOC-CTC-20060414-0002 v1.0...
Page 323: Firewall Commands
Firewall Commands Firewall Commands Introduction This chapter describes the commands of the firewall command group. Contents This chapter covers the following commands: firewall config Configure the firewall options. firewall clear Flush the firewall configuration. firewall list List the firewall configuration. firewall chain add Add a chain.
Page 324: Firewall Config
Firewall Commands firewall config Configure the firewall options. SYNTAX: firewall config [state = <{disabled | enabled}>] [keep = <{disabled | enabled}>] [tcpchecks = <{none | fast | exact}>] [udpchecks = <{disabled|enabled}>] [icmpchecks = <{disabled | enabled}>] [logdefault = <{disabled | enabled}>] [logthreshold = <{disabled | enabled}>] [tcpwindow = <number{0-1073725440}>] where:...
Page 325 Firewall Commands tcpwindow A number between 0 and 1073725440. OPTIONAL This parameter permits to modify the TCP window for fast TCP checks. The default is 65536. EXAMPLE: =>firewall config :firewall config state=enabled keep=disabled tcpchecks=none udpchecks=enabled icmpchecks=enabled logdefault=disabled logthreshold=enabled tcpwindow=65536 => E-DOC-CTC-20060414-0002 v1.0...
Page 326: Firewall Clear
Firewall Commands firewall clear Flush the firewall configuration. SYNTAX: firewall clear E-DOC-CTC-20060414-0002 v1.0...
Page 327: Firewall List
Firewall Commands firewall list List the firewall configuration. SYNTAX: firewall list [format = <{pretty | cli}>] where: format Select the output format in which the configuration must be shown. OPTIONAL Choose between: pretty: the configuration is shown as intuitive output in clear text. cli: the configuration is shown via the CLI commands configuration.
Page 328: Firewall Chain Add
Firewall Commands firewall chain add Add a chain. SYNTAX: firewall chain add chain = <string> where: chain The name of the chain to be added. REQUIRED EXAMPLE: =>firewall chain list Chains ====== Name Description ----------------------------------------------------------------- sink system forward system source system sink_fire system...
Page 329: Firewall Chain Delete
Firewall Commands firewall chain delete Delete a chain. SYNTAX: firewall chain delete chain = <string> where: chain The name of the chain to be deleted. REQUIRED EXAMPLE: =>firewall chain list Chains ====== Name Description ----------------------------------------------------------------- sink system forward system source system sink_fire system...
Page 330: Firewall Chain Flush
Firewall Commands firewall chain flush Flush all chains. SYNTAX: firewall chain flush E-DOC-CTC-20060414-0002 v1.0...
Page 331: Firewall Chain List
Firewall Commands firewall chain list List all chains. SYNTAX: firewall chain list [format = <{pretty | cli}>] where: format Select the output format in which the chains must be shown. OPTIONAL Choose between: pretty: the chains are shown as intuitive output in clear text. cli: the chains are shown via the CLI commands configuration.
Page 332: Firewall Debug Clear
Firewall Commands firewall debug clear Clear the firewall statistics. SYNTAX: firewall debug clear EXAMPLE: =>firewall debug stats Statistics ========== Used rule contexts Total rule contexts : 256 Total packets parsed : 2554 Packets parsed in hook sink : 1461 Packets parsed in hook forward : 12 Packets parsed in hook source : 1041...
Page 333: Firewall Debug Stats
Firewall Commands firewall debug stats Display the firewall statistics. SYNTAX: firewall debug stats EXAMPLE: =>firewall debug stats Statistics ========== Used rule contexts Total rule contexts : 256 Total packets parsed : 2554 Packets parsed in hook sink : 1461 Packets parsed in hook forward : 12 Packets parsed in hook source : 1041...
Page 334: Firewall Debug Traceconfig
Firewall Commands firewall debug traceconfig Configure the firewall trace options. SYNTAX: firewall debug traceconfig [tcpchecks = <{disabled | enabled}>] [udpchecks = <{disabled|enabled}>] [icmpchecks = <{disabled | enabled}>] [sink = <{none | all | accept | deny | drop | reset} or number>] [forward = <{none | all | accept | deny | drop reset} or number>] [source = <{none | all | accept | deny | drop...
Page 335: Firewall Level Add
Firewall Commands firewall level add Add a security level. SYNTAX: firewall level add name = <string> [index = <number>] [readonly = <{disabled | enabled}>] [udptrackmode = <{strict | loose}>] [service = <{disabled | enabled}>] [proxy = <{disabled|enabled}>] [text = <quoted string>] where: name The name of the security level to be added.
Page 336: Firewall Level Delete
Firewall Commands firewall level delete Delete a security level. SYNTAX: firewall level delete name = <string> where: name The name of the security level to be deleted. REQUIRED RELATED COMMANDS: firewall level add Add a security level. firewall level list List all the security levels.
Page 337: Firewall Level Flush
Firewall Commands firewall level flush Flush the security level configuration. SYNTAX: firewall level flush E-DOC-CTC-20060414-0002 v1.0...
Page 338: Firewall Level List
Firewall Commands firewall level list List all the security levels. SYNTAX: firewall level list [format = <{pretty | cli}>] where: format Select the output format in which the security levels must be shown. OPTIONAL Choose between: pretty: the security levels are shown as intuitive output in clear text. cli: the security levels are shown via the CLI commands configuration.
Page 339: Firewall Level Modify
Firewall Commands firewall level modify Configure a security level. SYNTAX: firewall level modify name = <string> [index = <number>] [readonly = <{disabled | enabled}>] [udptrackmode = <{strict | loose}>] [service = <{disabled | enabled}>] [proxy = <{disabled|enabled}>] [text = <quoted string>] where: name The name of the security level to be added.
Page 340: Firewall Level Set
Firewall Commands firewall level set Set the security level or display the current security level. SYNTAX: firewall level set [name = <string>] where: name The name of the security level to be set. OPTIONAL Note If no security level is specified, the current security level will be shown. E-DOC-CTC-20060414-0002 v1.0...
Page 341: Firewall Rule Add
Firewall Commands firewall rule add Add a firewall rule. SYNTAX: firewall rule add chain = <chain name> [index = <number>] [name = <string>] [clink = <chain name>] [srcintf [!]= <string>] [srcip [!]= <string>] [dstip [!]= <string>] [serv [!]= <string>] [log = <{disabled | enabled}>] [state = <{disabled | enabled}>] action = <{accept|deny|drop|reset|count|link}>...
Page 342: Firewall Rule Delete
Firewall Commands firewall rule delete Delete a firewall rule. SYNTAX: firewall rule delete chain = <string> index = <number> where: chain The name of the chain in which a rule must be deleted. REQUIRED index The number of the rule in the chain. REQUIRED RELATED COMMANDS: firewall rule add...
Page 343: Firewall Rule Flush
Firewall Commands firewall rule flush Flush all firewall rules. SYNTAX: firewall rule flush [chain = <string>] where: chain The name of the chain for which the rules must be flushed. OPTIONAL Note If not specified, the rules of all the chains will be flushed. E-DOC-CTC-20060414-0002 v1.0...
Page 344: Firewall Rule List
Firewall Commands firewall rule list Show a list of the firewall rules in a chain. SYNTAX: firewall rule list [chain = <string>] [format = <{pretty | cli}>] where: chain The name of the chain for which the rules must be listed. OPTIONAL Note If not specified, the rules of all the chains are shown.
Page 345 Firewall Commands EXAMPLE: =>firewall rule list Rules (flags: C=Constant, D=Dynamic, E=Enable, L=Log) ===== Chain Flags Rule --------------------------------------------------------------------------------------- sink : link sink_fire : link sink_system_service sink_fire SSDP : accept ssdp_serv lan.* > *.ssdp_ip sink_system_service HTTPI : accept HTTPI_sv_0 HTTPI_if_0.* > *.* PING_RESPONDER : accept PING_RESPONDER_sv_0 PING_RESPONDER_...
Page 346: Firewall Rule Modify
Firewall Commands firewall rule modify Modify a firewall rule. SYNTAX: firewall rule modify chain = <string> index = <number> [newindex = <number>] [name = <string>] [clink = <chain name>] [srcintf [!]= <string>] [srcip [!]= <string>] [dstintf [!]= <string>] [dstip [!]= <string>] [serv [!]= <string>] [log = <{disabled | enabled}>] [state = <{disabled | enabled}>]...
Page 347: Firewall Rule Debug Clear
Firewall Commands firewall rule debug clear Clear the firewall rule statistics. SYNTAX: firewall rule debug clear [chain = <string>] [index = <number>] where: chain The name of the chain which contains the rule. OPTIONAL index The number of the rule in the chain. OPTIONAL Note If not specified, the statistics for all the rules in the chain will be cleared.
Page 348 Firewall Commands RELATED COMMANDS: firewall rule debug stats Show the firewall rule statistics. E-DOC-CTC-20060414-0002 v1.0...
Page 349: Firewall Rule Debug Stats
Firewall Commands firewall rule debug stats Show the firewall rule statistics. SYNTAX: firewall rule debug stats [chain = <chain name>] [index = <number>] where: chain The name of the chain for which the statistics must be shown. OPTIONAL Note If not specified, the statistics for all the chains will be shown. index The number of the rule in the chain.
Page 350: Firewall Rule Debug Traceconfig
Firewall Commands firewall rule debug traceconfig Display or modify the rule trace configuration. SYNTAX: firewall rule debug traceconfig [trace = <{disabled | enabled}>] where: trace Enable or disable rule traces. OPTIONAL The default is disabled. EXAMPLE: =>firewall rule debug traceconfig :firewall rule debug traceconfig state=disabled =>...
Page 351: Grp Commands
GRP Commands GRP Commands Introduction This chapter describes the commands of the grp command group. Contents This chapter covers the following commands: grp config Set the Generic Routing Protocol (GRP) configuration settings. grp flush Flush the GRP interface settings and parameters. grp rtlist Show the current routes in the GRP interfaces routing table.
Page 352: Grp Config
GRP Commands grp config Set the Generic Routing Protocol (GRP) configuration settings. SYNTAX: grp config [cdistance = <number{0-255}>] [kdistance = <number{0-255}>] [rdistance = <number{0-255}>] [trace = <{disabled | enabled}>] where: cdistance A number between 0 and 255. OPTIONAL Sets the distance of the connected route type. The default is 0.
Page 353: Grp Flush
GRP Commands grp flush Flush the GRP interface settings and parameters. SYNTAX: grp flush E-DOC-CTC-20060414-0002 v1.0...
Page 354: Grp Rtlist
GRP Commands grp rtlist Show the current routes in the GRP interfaces routing table. SYNTAX: grp rtlist [dst = <ip-address>] [dstmask = <ip-mask (dotted or cidr)>] where: The destination IP address of the route. OPTIONAL Supports IP/mask notation. Note If no destination IP address is specified, all the current routes will be shown.
Page 355: Grp Rip Config
GRP Commands grp rip config Configure the RIP settings. SYNTAX: grp rip config state = <{disabled | enabled}> [version = <{rip_unspec | rip_v1 | rip_v2}>] [defmetric = <number{1-16}>] [updatetime = <number{1-3600}>] [timeouttime = <number{1-3600}>] [garbagetime = <number{1-3600}>] [impcrt = <{disabled | enabled}>] [impkrt = <{disabled | enabled}>] [impsrt = <{disabled | enabled}>] [impdefkrt = <{disabled | enabled}>]...
Page 356 GRP Commands impsrt Enable or disable the import of static routes. OPTIONAL The default is enabled. impdefkrt Enable or disable the import of the default kernel route. OPTIONAL The default is enabled. impdefsrt Enable or disable the import of the default static route. OPTIONAL The default is enabled.
Page 357: Grp Rip Flush
GRP Commands grp rip flush Flush the RIP interface settings and global parameters. SYNTAX: grp rip flush E-DOC-CTC-20060414-0002 v1.0...
Page 358: Grp Rip Ifconfig
GRP Commands grp rip ifconfig Configure a RIP interface. SYNTAX: grp rip ifconfig intf = <string> [rip = <{disabled | enabled}>] [rxversion = <{rip_unspec | rip_v1 | rip_v2 | rip_v1-2}>] [authmode = <{none | cleartext}>] [authstring = <quoted string>] [splithorizon = <{disable | enable}>] where: intf The name of the RIP interface to be configured.
Page 359: Grp Rip Show
GRP Commands grp rip show Show the RIP settings and the routes in the RIP database. SYNTAX: grp rip show EXAMPLE: =>grp rip show RIP routing protocol config dump ------------------------------------ RIP daemon is enabled Global RIP queries received : 0 Global RIP route changes : 3 Default version : send rip_v2, receive rip_v2 Default redistribution metric is 1...
Page 360 GRP Commands E-DOC-CTC-20060414-0002 v1.0...
Page 361: Hostmgr Commands
Hostmgr Commands Hostmgr Commands Introduction This chapter describes the commands of the hostmgr command group. Contents This chapter covers the following commands: hostmgr add Add host device info to the host manager. hostmgr clear Remove all the hosts from the list. hostmgr config Configure the host manager parameters.
Page 362: Hostmgr Add
Hostmgr Commands hostmgr add Add host device info to the host manager. SYNTAX: hostmgr add mac_addr = <hardware-address> [ip_addr = <ip-address>] [name = <string>] [type = <{generic_device|desktop_computer|laptop_computer| set_top_box|pda|gaming_console|phone|mobile_phone| printer|mass_storage_device}>] [ipintf = <string>] [ethintf = <string>] [physintf = <string>] where: mac_addr The MAC address of the host to be added.
Page 363 Hostmgr Commands EXAMPLE: =>hostmgr list MAC-address IP-address Flags Type Intf Hw Intf Hostname ----------- ---------- ----- ---- ---- ------- -------- 00:10:a4:ad:32:cf 192.168.1.64 Generic Device LocalNetwork ethif4 MyComputer =>hostmgr add mac_addr=00:10:a4:33:56:53 name=Play type=Playstation =>hostmgr list MAC-address IP-address Flags Type Intf Hw Intf Hostname ----------- ----------...
Page 364: Hostmgr Clear
Hostmgr Commands hostmgr clear Remove all the hosts from the list. SYNTAX: hostmgr clear EXAMPLE: =>hostmgr list MAC-address IP-address Flags Type Intf Hw Intf Hostname ----------- ---------- ----- ---- ---- ------- -------- 00:10:a4:33:56:53 0.0.0.0 Playstation ethif1 ethif1 Play 00:10:a4:ad:32:cf 192.168.1.64 Generic Device LocalNetwork ethif4...
Page 365: Hostmgr Config
Hostmgr Commands hostmgr config Configure the host manager parameters. SYNTAX: hostmgr config [state = <{disabled | enabled}>] [scantime = <number{10-600}>] [autosave = <{disabled | enabled}>] [trace = <{disabled | enabled}>] where: state Enable or disable the host manager daemon. OPTIONAL The default is enabled.
Page 366: Hostmgr Delete
Hostmgr Commands hostmgr delete Delete the host device info from the host manager. SYNTAX: hostmgr delete mac_addr = <hardware-address> where: mac_addr The MAC address of the host to be removed. REQUIRED EXAMPLE: =>hostmgr list MAC-address IP-address Flags Type Intf Hw Intf Hostname ----------- ----------...
Page 367: Hostmgr Flush
Hostmgr Commands hostmgr flush Flush the host manager configuration. The host manager configuration is cleaned and returned to default values. SYNTAX: hostmgr flush E-DOC-CTC-20060414-0002 v1.0...
Page 368: Hostmgr List
Hostmgr Commands hostmgr list List all the host devices. SYNTAX: hostmgr list EXAMPLE: =>hostmgr list MAC-address IP-address Flags Type Intf Hw Intf Hostname ----------- ---------- ----- ---- ---- ------- -------- 00:10:a4:33:56:53 0.0.0.0 Playstation ethif1 ethif1 Play 00:10:a4:ad:32:cf 192.168.1.64 Generic Device LocalNetwork ethif4 MyComputer...
Page 369: Ids Commands
IDS Commands IDS Commands Introduction This chapter describes the commands of the ids command group. Contents This chapter covers the following commands: ids clear Reset the IDS statistics. ids config Display/modify the Intrusion Detection System (IDS) configuration. ids parser list Display the IDS parser configuration.
Page 370: Ids Clear
IDS Commands ids clear Reset the IDS statistics. SYNTAX: ids clear RELATED COMMANDS: ids parser list Display the IDS parser configuration. E-DOC-CTC-20060414-0002 v1.0...
Page 371: Ids Config
IDS Commands ids config Display/modify the Intrusion Detection System (IDS) configuration. SYNTAX: ids config [state = <{disabled | enabled}>] [trace = <{disabled|enabled}>] where: state Enable or disable IDS checks. OPTIONAL The default is enabled. trace Enable or disable tracing. OPTIONAL The default is disabled.
Page 372: Ids Parser List
IDS Commands ids parser list Display the IDS parser configuration. SYNTAX: ids parser list [parser = <parser>] where: parser The name of the parser REQUIRED EXAMPLE: =>ids parser list parser state ----------------------------------------- fragment enabled scan enabled enabled proto enabled rate enabled =>...
Page 373: Ids Parser Modify
IDS Commands ids parser modify Modify the IDS parser configuration. SYNTAX: ids parser modify parser = <string> state = <{disabled | enabled}> where: parser The name of the IDS parser of which the configuration must be modified. REQUIRED state Disable or enable the parser. REQUIRED EXAMPLE: =>ids list...
Page 374: Ids Pattern Clear
IDS Commands ids pattern clear Reset the pattern tracker. SYNTAX: ids pattern clear EXAMPLE: =>ids pattern stats Pattern tracker statistics: --------------------------- memory : 32768 bytes maximum number of patterns : 512 number of active patterns number of recycled patterns number of pattern searches number of new patterns maximum number of hash collisions % of hash entries with collisions...
Page 375: Ids Pattern List
IDS Commands ids pattern list Display the patterns in the pattern tracker. SYNTAX: ids pattern list [size = <{10 | 100 | full} or number>] where: size The size of the IDS pattern list that will be shown. OPTIONAL Choose between: full or, alternatively, specify a number.
Page 376: Ids Pattern Stats
IDS Commands ids pattern stats Display the pattern tracker statistics. SYNTAX: ids pattern stats EXAMPLE: =>ids pattern stats Pattern tracker statistics: --------------------------- memory : 32768 bytes maximum number of patterns : 512 number of active patterns number of recycled patterns number of pattern searches number of new patterns maximum number of hash collisions...
Page 377: Ids Signature List
IDS Commands ids signature list Displays the ids signature configuration SYNTAX ids signature list [signature = <fragment_sweep|zero-length_fragment_size| small_fragment_size|fragment_size_overrun| fragment_overlap|fragment_out-of-order| ip_protocol_scan|tcp_port_scan|tcp_syn_scan| stealth_tcp_null_scan|stealth_tcp_fin_scan| stealth_tcp_xmas_scan| stealth_tcp_full_xmas_scan| stealth_tcp_vecna_scan| stealth_tcp_syn-fin_scan| udp_port_scan|ping_sweep_scan|tcp_syn_flood| udp_flood|ping_flood|icmp_unreachable_storm| smurf_broadcast_attack|smurf_storm_attack| fraggle_broadcast_attack| fraggle_storm_attack|land_attack}>] where signature The name of the signature OPTIONAL EXAMPLE: =>ids signature list signature fragment_sweep signature parser hits action...
Page 378: Ids Signature Modify
IDS Commands ids signature modify Modify the states of the signatures. SYNTAX ids signature modify [signature = <fragment_sweep| zero-length_fragment_size| small_fragment_size| fragment_size_overrun| fragment_overlap| fragment_out-of-order| ip_protocol_scan| tcp_port_scan|tcp_syn_scan| stealth_tcp_null_scan| stealth_tcp_fin_scan| stealth_tcp_xmas_scan| stealth_tcp_full_xmas_scan| stealth_tcp_vecna_scan| stealth_tcp_syn-fin_scan| udp_port_scan|ping_sweep_scan| tcp_syn_flood|udp_flood|ping_flood| icmp_unreachable_storm| smurf_broadcast_attack| smurf_storm_attack| fraggle_broadcast_attack| fraggle_storm_attack|land_attack}>] state = <{disabled|enabled}> where signature The name of the signature...
Page 379: Ids Threshold Clear
IDS Commands ids threshold clear Reset the IDS thresholds to their default values. SYNTAX: ids threshold clear EXAMPLE: =>ids threshold list index name window limit scaling ----------------------------------------------------------------- ids scan enabled ids flood disabled ids tcp rate enabled ids udp rate disabled ids icmp rate disabled...
Page 380: Ids Threshold List
IDS Commands ids threshold list Display the IDS thresholds. SYNTAX: ids threshold list EXAMPLE: =>ids threshold list index name window limit scaling ----------------------------------------------------------------- ids scan enabled ids flood disabled ids tcp rate disabled ids udp rate disabled ids icmp rate disabled ids ip rate disabled...
Page 381: Ids Threshold Modify
IDS Commands ids threshold modify Modify the IDS thresholds. SYNTAX: ids threshold modify index = <number> [window = <number>] [limit = <number>] [scaling = <{disabled | enabled}>] where: index The index of the IDS threshold to be modified. REQUIRED Use the command :ids threshold list to obtain the indexes. window A number (of seconds).
Page 382 IDS Commands E-DOC-CTC-20060414-0002 v1.0...
Page 383: Igmp Commands
IGMP Commands IGMP Commands Introduction This chapter describes the commands of the IGMP command group. Contents This chapter covers the following commands: igmp host config Display or modify global IGMP configuration. igmp host flush Flush the IGMP settings. igmp host list Show the IGMP groups.
Page 384: Igmp Host Config
IGMP Commands igmp host config Display or modify global IGMP configuration. SYNTAX: igmp host config [requirera = <{disabled | enabled}>] where: requirera Enable or disable the router alert IP option check. OPTIONAL The default is disabled. EXAMPLE: =>igmp host confighostmgr list Router alert IP option check : disabled =>...
Page 385: Igmp Host Flush
IGMP Commands igmp host flush Flush the IGMP settings. SYNTAX: igmp host flush E-DOC-CTC-20060414-0002 v1.0...
Page 386: Igmp Host List
IGMP Commands igmp host list Show the IGMP groups. SYNTAX: igmp host list [intf = <string>] [expand = <{disabled | enabled}>] where: intf The IP interface name. OPTIONAL expand Enable or disable expanded listing of IGMP groups. OPTIONAL The default is disabled. EXAMPLE: =>igmp host list Interface...
Page 387: Igmp Host Ifconfig
IGMP Commands igmp host ifconfig Configure an IGMP interface. SYNTAX: igmp host ifconfig intf = <string> version = <{none |IGMPv1 |IGMPv2 |IGMPv3}> where: intf The IP interface name. REQUIRED version The IGMP version of the IP interface. REQUIRED Choose between: IGMPv1 IGMPv2 IGMPv3...
Page 388: Igmp Host Iflist
IGMP Commands igmp host iflist Show the configuration of the IGMP interfaces. SYNTAX: igmp host iflist [expand = <{disabled | enabled}>] where: expand Enable or disable expanded listing of IGMP interfaces configuration. OPTIONAL The default is disabled. EXAMPLE: =>igmp host iflist Interface Version loop...
Page 389: Igmp Host Debug Clear
IGMP Commands igmp host debug clear Clear IGMP statistics. SYNTAX: igmp host debug clear RELATED COMMANDS: igmp host debug stats Print IGMP statistics. E-DOC-CTC-20060414-0002 v1.0...
Page 390: Igmp Host Debug Stats
IGMP Commands igmp host debug stats Print IGMP statistics. SYNTAX: igmp host debug stats EXAMPLE: =>igmp host debug stats Total IGMP messages received Too small IGMP messages received Too long IGMP messages received IGMP messages with bad checksum received IGMP messages with bad TTL received IGMP messages with no router alert IP option received IGMPv1 membership queries received IGMPv2 membership queries received...
Page 391: Igmp Proxy Config
IGMP Commands igmp proxy config Configure the IGMP proxy. SYNTAX: igmp proxy config [state = <{disabled | enabled}>] [qi = <number{1-86400}>] [qri = <number{1-86400}>] [lmqi = <number{1-86400}>] [rv = <number{2-10}>] [requirera = <{disabled | enabled}>] [localgroup = <{disabled | enabled}>] where: state Enable or disable the IGMP proxy.
Page 392 IGMP Commands RELATED COMMANDS: igmp proxy grouplist Show the learned groups on an IGMP proxy interface. E-DOC-CTC-20060414-0002 v1.0...
Page 393: Igmp Proxy Flush
IGMP Commands igmp proxy flush Flush all IGMP proxy settings and learned groups. SYNTAX: igmp proxy flush E-DOC-CTC-20060414-0002 v1.0...
Page 394: Igmp Proxy Grouplist
IGMP Commands igmp proxy grouplist Show the learned groups on an IGMP proxy interface. SYNTAX: igmp proxy grouplist [intf = <string>] [expand = <{disabled | enabled}>] where: intf The name of the IGMP proxy interface to be listed. OPTIONAL expand Enable or disable expanded listing of the learned groups on an OPTIONAL IGMP proxy interface.
Page 395: Igmp Proxy Ifconfig
IGMP Commands igmp proxy ifconfig Configure an IGMP proxy interface. SYNTAX: igmp proxy ifconfig intf = <string> [state = <{inactive | downstream | upstream}>] [version = <{IGMPv1 | IGMPv2 | IGMPv3}>] [fastleave = <{disabled | enabled}>] where: intf The name of the IGMP proxy interface to be configured. REQUIRED state The state of the IGMP proxy interface.
Page 396: Igmp Proxy Iflist
IGMP Commands igmp proxy iflist Show the configuration of an IGMP proxy interface. SYNTAX: igmp proxy iflist [expand = <{disabled | enabled}>] where: expand Enable or disable expanded listing of IGMP proxy interface OPTIONAL configuration. The default is disabled. EXAMPLE: =>igmp proxy iflist Interface State...
Page 397: Igmp Proxy Mbslist
IGMP Commands igmp proxy mbslist Show the IGMP proxy membership database (merge of all learned groups. SYNTAX: igmp proxy mbslist E-DOC-CTC-20060414-0002 v1.0...
Page 398: Igmp Proxy Debug Clear
IGMP Commands igmp proxy debug clear Clear IGMP proxy statistics. SYNTAX: igmp proxy debug clear RELATED COMMANDS: igmp proxy debug stats Print IGMP proxy statistics. igmp proxy debug Modify IGMP proxy trace configuration. traceconfig E-DOC-CTC-20060414-0002 v1.0...
Page 399: Igmp Proxy Debug Stats
IGMP Commands igmp proxy debug stats Print IGMP proxy statistics. SYNTAX: igmp proxy debug stats EXAMPLE: =>igmp proxy debug stats IGMP proxy statistics: Total IGMP packets recv Too short IGMP packets recv IGMP packets with bad checksum recv IGMP packets with bad ttl recv IGMP packets with no route alert option recv IGMPv1 queries recv IGMPv2 queries recv...
Page 400: Igmp Proxy Debug Traceconfig
IGMP Commands igmp proxy debug traceconfig Modify IGMP proxy trace configuration. SYNTAX: igmp proxy debug traceconfig [state = <{disabled | enabled}>] where: state Enable or disable tracing. OPTIONAL The default is disabled. RELATED COMMANDS: igmp proxy debug clear Clear IGMP proxy statistics. igmp proxy debug stats Print IGMP proxy statistics.
Page 401: Interface Commands
Interface Commands Interface Commands Introduction This chapter describes the commands of the interface command group. Contents This chapter covers the following commands: interface list Display interfaces. E-DOC-CTC-20060414-0002 v1.0...
Page 402: Interface List
Interface Commands interface list Display interfaces. SYNTAX: interface list [expand = <{disabled | enabled}>] [reverse = <{disabled | enabled}>] where: expand Enable or disable expanded listing of interfaces. OPTIONAL The default is disabled. reverse Enable or disable reverse listing (lower layer first instead of upper layer first). OPTIONAL The default is disabled.
Page 403 Interface Commands EXAMPLE: =>interface list Name Type State UL Interfaces ethif1 physical connected bridge ethif4 physical connected bridge usbif1 physical connected bridge RELAY connected Internet_ppp bridge connected eth0 atm_0_35 connected ethoa_0_35 atm_8_35 connected ethoa_8_35 ethoa_0_35 connected ethoa_8_35 connected Internet_ppp ppp not-connected Internet Internet...
Page 404 Interface Commands E-DOC-CTC-20060414-0002 v1.0...
Page 405: Ip Commands
IP Commands IP Commands Introduction This chapter describes the commands of the ip command group. Contents This chapter covers the following commands: ip arpadd Add an entry to the ARP cache of a broadcast Internet Protocol (IP) interface. ip arpdelete Delete an entry from the ARP cache.
Page 406 IP Commands ip debug sendto Send UDP packets. ip debug stats Display IP statistics. ip debug traceconfig Display/modify the IP stack trace configuration. E-DOC-CTC-20060414-0002 v1.0...
Page 407: Ip Arpadd
IP Commands ip arpadd Add an entry to the ARP cache of a broadcast Internet Protocol (IP) interface. SYNTAX: ip arpadd intf = <string> ip = <ip-range> [hwaddr = <hardware-address>] where: intf The IP interface name. REQUIRED The IP address (or range) of the entry to be added to the Address Resolution Protocol REQUIRED (ARP) cache.
Page 408: Ip Arpdelete
IP Commands ip arpdelete Delete an entry from the ARP cache. SYNTAX: ip arpdelete intf = <string> ip = <ip-range> [hwaddr = <hardware-address>] where: intf The IP interface name. REQUIRED The IP address (or range) of the entry to be deleted. REQUIRED hwaddr The hardware address (for example the Ethernet MAC address) of the entry to be...
Page 409: Ip Arplist
IP Commands ip arplist Display the ARP cache. SYNTAX: ip arplist EXAMPLE: =>ip arplist Interface IP-address HW-address Type eth0 10.0.0.1 00:10:a4:ad:32:cf STATIC eth0 10.0.0.2 00:00:00:00:00:00 DYNAMIC eth0 10.0.0.3 00:a0:24:ae:66:e1 STATIC => RELATED COMMANDS: ip arpadd Add an entry to the ARP cache of a broadcast Internet Protocol (IP) interface. ip arpdelete Delete an entry from the ARP cache.
Page 410: Ip Config
IP Commands ip config Show/set global IP stack configuration options. SYNTAX: ip config [forwarding = <{disabled | enabled}>] [redirects = <{disabled | enabled}>] [checkoptions = <{disabled|enabled|transparent}>] [netbroadcasts = <{disabled | enabled}>] [ttl = <number{0-255}>] [defragmode = <{disabled | enabled}>] [addrcheck = <{off | own | static | dynamic}>] [mssclamping = <{disabled | enabled}>] [natloopback = <{disabled|enabled}>] [bitrate-window(sec) = <number{10-3600}>]...
Page 411 Minimum level of checking. Only the address configuration on the SpeedTouch™ is checked. static: Checking of the address configuration of the SpeedTouch™ and also of traffic: addresses of incoming packets; this checking is related to constants (for example an address may not be entirely composed of one‘s or zero‘s).
Page 412: Ip Flush
IP Commands ip flush Flush all the static IP parameters. Dynamic configurations (for example from PPP or CIP links) remain. The flush command does not impact previously saved configurations. The command :ip flush deletes all local IP connectivity. Do not use this command during an IP based local connection, for example a Telnet CLI session, or web based CLI access.
Page 413: Ip Ifadd
IP Commands ip ifadd Create an IP interface. SYNTAX: ip ifadd intf = <string> dest = <string> where: intf The name of the IP interface to be created. REQUIRED dest An network interface name. REQUIRED EXAMPLE: =>ip iflist Interface Group TX-Drop Status HW-address loop...
Page 414: Ip Ifattach
IP Commands ip ifattach Attach an IP interface. SYNTAX: ip ifattach intf = <string> where: intf The name of the IP interface to be attached. REQUIRED EXAMPLE: =>ip iflist Interface Group TX-Drop Status HW-address loop local 65535 123966 75177 [UP] 00:0e:50:0f:fc:2c Internet 1500...
Page 415: Ip Ifconfig
IP Commands ip ifconfig Configure the parameters of an IP interface. SYNTAX: ip ifconfig intf = <string> [mtu = <number{68-65535}>] [status = <{down | up}>] [hwaddr = <hardware-address>] [group = <string> or number] [linksensing = <{disabled | enabled}>] [primary = <{disabled | enabled}>] [mcastpromisc = <{disabled|enabled}>] where: intf...
Page 416 IP Commands EXAMPLE: =>ip iflist Interface Group TX-Drop Status HW-address loop local 65535 123966 75177 [UP] 00:0e:50:0f:fc:2c Internet 1500 DOWN RtPPPoE_ppp 1500 DOWN LocalNetwork 1500 86589 125262 [UP] 00:0e:50:0f:fc:2c myIPintf 1500 DOWN 00:0e:50:0f:fc:2c =>ip ifconfig intf = myIPintf [mtu] = 1500 [status] = up [hwaddr] = 00:0e:50:0f:fc:2c [group] = wan...
Page 417: Ip Ifdelete
IP Commands ip ifdelete Delete an IP interface. SYNTAX: ip ifdelete intf = <string> where: intf The name of the IP interface to be deleted. REQUIRED EXAMPLE: =>ip iflist Interface Group TX-Drop Status HW-address loop local 65535 123966 75177 [UP] 00:0e:50:0f:fc:2c Internet 1500...
Page 418: Ip Ifdetach
IP Commands ip ifdetach Detach an IP interface. SYNTAX: ip ifdetach intf = <string> where: intf The name of the IP interface to be detached. REQUIRED EXAMPLE: =>ip iflist expand=enabled Interface Group TX-Drop Status HW-address loop local 65535 130597 82240 [UP] 00:0e:50:0f:fc:2c BRHW-address...
Page 419: Ip Iflist
IP Commands ip iflist Display all the IP interfaces. SYNTAX: ip iflist [expand = <{disabled | enabled}>] where: expand Enable or disable expanded listing. OPTIONAL The default is disabled. EXAMPLE: =>ip iflist Interface Group TX-Drop Status HW-address loop local 65535 123966 75177 [UP] 00:0e:50:0f:fc:2c...
Page 420: Ip Ifwait
IP Commands ip ifwait Wait for a status change of an IP interface. SYNTAX: ip ifwait intf = <string> [timeout = <number{1-600000}>] [adminstatus = <{down | up}>] [operstatus = <{down | up}>] [linkstatus = <{down | up}>] where: intf The IP interface name. REQUIRED timeout A number between 1 and 600000 (seconds).
Page 421: Ip Ipadd
IP Commands ip ipadd Assign an IP address to an IP interface. SYNTAX: ip ipadd intf = <string> addr = <ip-address> [netmask = <ip-mask(dotted or cidr)>] [pointopoint = <ip-address>] [addroute = <{disabled | enabled}>] where: intf The IP interface name. REQUIRED addr The new IP address to be added.
Page 422: Ip Ipconfig
IP Commands ip ipconfig Modify an IP address configuration. SYNTAX: ip ipconfig addr = <ip-address> [preferred = <{disabled | enabled}>] [primary = <{disabled | enabled}>] where: addr The IP address to be configured. REQUIRED preferred Make this IP address the preferred address for that subnet (enabled) or not OPTIONAL (disabled).
Page 423: Ip Ipdelete
IP Commands ip ipdelete Remove an IP address from an IP interface. SYNTAX: ip ipdelete addr = <ip-address> where: addr The IP address to be deleted. REQUIRED EXAMPLE: =>ip iplist Interface Type IP-address Point-to-point/Mask eth0 Ethernet 10.0.0.2 255.255.255.0 eth0 Ethernet 10.0.0.138 255.255.255.0 eth0...
Page 424: Ip Iplist
IP Commands ip iplist Display all the configured IP addresses. SYNTAX: ip iplist EXAMPLE: =>ip iplist Interface Type IP-address Point-to-point/Mask LocalNetwork Ethernet 10.0.0.138 255.255.255.0 LocalNetwork Ethernet *192.168.1.254 255.255.255.0 loop Ethernet 127.0.0.1 255.255.255.255 => RELATED COMMANDS: ip ipadd Assign an IP address to an IP interface. ip ipdelete Remove an IP address from an IP interface.
Page 425: Ip Mcast Rtadd
IP Commands ip mcast rtadd Add a multicast route to the multicast routing table. SYNTAX: ip mcast rtadd srcintf = <string> [src = <ip-address>] grp = <ip-address> dstintf = <string> [ttl = <number{1-255}>] [ttlincr = {disabled | enabled}] where: srcintf The source IP interface.
Page 426: Ip Mcast Rtdelete
IP Commands ip mcast rtdelete Delete a multicast route from the multicast routing table. SYNTAX: ip mcast rtdelete srcintf = <string> [src = <ip-address>] grp = <ip-address> dstintf = <string> where: srcintf The source IP interface. REQUIRED The source IP address. OPTIONAL The multicast group IP address.
Page 427: Ip Mcast Rtlist
IP Commands ip mcast rtlist Display the multicast routing table. SYNTAX: ip mcast rtlist [expand = <{disabled | enabled}>}] where: expand Enable or disable expanded listing. OPTIONAL The default is disabled. RELATED COMMANDS: ip mcast rtadd Add a multicast route to the multicast routing table. ip mcast rtdelete Delete a multicast route from the multicast routing table.
Page 428: Ip Mcast Flush
IP Commands ip mcast flush Flush the multicast routing table. SYNTAX: ip mcast flush RELATED COMMANDS: ip mcast rtadd Add a multicast route to the multicast routing table. ip mcast rtdelete Delete a multicast route from the multicast routing table. ip mcast rtlist Display the multicast routing table.
Page 429: Ip Rtadd
IP Commands ip rtadd Add a route to the routing table. SYNTAX: ip rtadd dst = <ip-address> [dstmsk = <ip-mask(dotted or cidr)>] [label = <string>] [gateway = <ip-address>] [intf = <string>] [srcintf = <string>] [metric = <number{0-255}>] where: The destination IP address(es) for this route. REQUIRED Note Supports ip/mask notation.
Page 430: Ip Rtdelete
IP Commands ip rtdelete Delete a route from the routing table. SYNTAX: ip rtdelete dst = <ip-address> [dstmsk = <ip-mask(dotted or cidr)>] [label = <string>] [gateway = <ip-address>] [intf = <string>] where: The destination IP address(es) for this route. REQUIRED Note Supports cidr notation.
Page 431: Ip Rtlist
IP Commands ip rtlist Display the routing table. SYNTAX: ip rtlist [expand = <{disabled | enabled}>] where: expand Enable or disable expanded listing. OPTIONAL The default is disabled. EXAMPLE: =>ip rtlist Destination Label Gateway Interface Metric Status 10.0.0.138/32 127.0.0.1 loop [UP] 127.0.0.1/32 127.0.0.1...
Page 432: Ip Auto Flush
IP Commands ip auto flush Flush the autoIP interfaces. SYNTAX: ip auto flush E-DOC-CTC-20060414-0002 v1.0...
Page 433: Ip Auto Ifadd
IP Commands ip auto ifadd Create an autoIP interface. SYNTAX: ip auto ifadd intf = <string> [addr = <ip-address>] where: intf The name of the IP interface for which a link-local address has to be allocated. REQUIRED dest The preferred link-local IP address. OPTIONAL EXAMPLE: =>ip auto ifadd intf=eth0...
Page 434: Ip Auto Ifattach
IP Commands ip auto ifattach Select and assign a link-local address to an autoIP interface. SYNTAX: ip auto ifattach intf = <string> where: intf The name of the autoIP interface for which a link-local address has to be attached. REQUIRED EXAMPLE: =>...
Page 435: Ip Auto Ifconfig
IP Commands ip auto ifconfig Configure an autoIP interface. SYNTAX: ip auto ifconfig intf = <string> [addr = <ip-address>] [poolstart = <ip-address>] [poolend = <ip-address>] [netmask = <ip-mask(dotted or cidr)>] [claim = <number{0-65535}>] [defence = <number{0-65535}>] [probe = <number{0-65535}>] [interval = <number{1-65535}>] where: intf The name of the autoIP interface to be configured.
Page 436 IP Commands EXAMPLE: => ip auto iflist eth0 : [INIT] 0.0.0.0 poolstart = 169.254.1.1 poolend = 169.254.254.254 netmask = 255.255.0.0 claim : 10 defence : 5 probe : 4 interval : 2 (sec) probes sent = 0 collisions =>ip auto ifconfig intf=ipsec0 claim=5 probe=5 =>...
Page 437: Ip Auto Ifdelete
IP Commands ip auto ifdelete Delete an existing autoIP interface. SYNTAX: ip auto ifdelete intf = <string> where: intf The name of the IP interface to be deleted. REQUIRED EXAMPLE: =>ip auto iflist ipsec0 : [SELECTING] 169.254.80.236 poolstart = 169.254.1.1 poolend = 169.254.254.254 netmask = 255.255.0.0 claim : 10...
Page 438: Ip Auto Ifdetach
IP Commands ip auto ifdetach Release the link-local address for the given autoIP interface. SYNTAX: ip auto ifdetach intf = <string> where: intf The name of the autoIP interface for which a link-local address has to be detached. REQUIRED EXAMPLE: =>ip auto iflist ipsec0 : [SELECTING] 169.254.80.236...
Page 439: Ip Auto Iflist
IP Commands ip auto iflist Display the autoIP interfaces. SYNTAX: ip auto iflist [intf = <string>] where: intf The name of the autoIP interface to be listed. OPTIONAL Note If not specified, all the autoIP interfaces are shown. EXAMPLE: =>ip auto iflist eth0 : [CLAIMED] 169.254.138.1 poolstart = 169.254.1.1...
Page 440: Ip Debug Httpprobe
RTT taken to send a request and get a response back from the HTTP Server (the probe retrieves the base HTML page only as body, and does not request hyperlinks within this page). The SpeedTouch will send the HTTP request, receive the reply, and report the RTT statistics (including the size of the page returned).
Page 441: Ip Debug Sendto
IP Commands ip debug sendto Send UDP packets. SYNTAX: ip debug sendto addr = <ip-address> [count = <number{1-1000000}>] [size = <number{0-20000}>] [interval = <number{1-1000000}>] [listen = <{disabled | enabled}>] [dffield = <{disabled | enabled}>] [srcaddr = <ip-address>] [srcport = <number{1-65535}>] dstport = <number{1-65535}>...
Page 442 IP Commands EXAMPLE: =>ip debug sendto addr=10.0.0.148 listen=on srcport=19 dstport=1025 =>ip debug sendto addr=10.0.0.148 listen=on srcport=19 dstport=1025 1 bytes from 10.0.0.148:1025 =>ip debug sendto addr=10.0.0.148 count=3 listen=on srcport=19 dstport=1025 1 bytes from 10.0.0.148:1025 1 bytes from 10.0.0.148:1025 1 bytes from 10.0.0.148:1025 =>...
Page 443: Ip Debug Stats
IP Commands ip debug stats Display IP statistics. SYNTAX: ip debug stats EXAMPLE: =>ip debug stats Total datagrams received : 8599 IP header errors Datagrams forwarded : 23 Datagram forwarding errors Datagram forwarding resource errors Total Fragments received Fragments dropped due to resources or timeouts Datagrams reassembled Datagrams fragmented successfully Datagram fragmentation errors...
Page 444: Ip Debug Traceconfig
IP Commands ip debug traceconfig Display/modify the IP stack trace configuration. SYNTAX: ip debug traceconfig [input = <{none | label | -telnet | -host | -broadcast | all}>] [forward = <{none | label | -telnet | -host | -broadcast | all}>] [output = <{none | label | -telnet | -host | -broadcast | all}>] [drop = <{none | label | -telnet | -host | -broadcast...
Page 445 IP Commands EXAMPLE: =>ip debug traceroute addr = 192.193.195.250 count=3 size=1 interval=1000 maxhops=30 dstport=33433 maxfail=5 type=icmp utime=yes :ip debug traceroute addr=192.193.195.250 ttl=1 192.193.195.250 676 us 1351 us 648 us => E-DOC-CTC-20060414-0002 v1.0...
Page 446 IP Commands E-DOC-CTC-20060414-0002 v1.0...
Page 447: Ipqos Commands
IPQoS Commands IPQoS Commands Introduction This chapter describes the commands of the ipqos command group. Contents This chapter covers the following commands: ipqos config Configure IPQoS for a given destination interface for the IPQoS queues instantiation. ipqos list Display the IPQoS configuration. ipqos ef config Configure the IPQoS Expedited Forwarding (EF) timer for an interface.
Page 448: Ipqos Config
IPQoS Commands ipqos config Configure IPQoS for a given destination interface for the IPQoS queues instantiation. When enabling or disabling IPQoS, take the following into account: if the WAN interface (for example PPPoA, IP oA,...) is detached at the time of enabling/disabling IPQoS, then the WAN interface has to be attached in order for the enabling/disabling of IPQoS to take effect.
Page 449 IPQoS Commands realtimerate A number between 1 and 100. OPTIONAL Represents a percentage of the interface bandwidth for rate-limiting of the Real Time queue. In case of congestion, the Real Time queue will only use this percentage of the interface bandwidth when there is also traffic on the other queues. The default is 80.
Page 450: Ipqos List
IPQoS Commands ipqos list Display the IPQoS configuration. SYNTAX: ipqos list EXAMPLE: =>ipqos list Name State Discard Priority Size Size Rate Burst Weights (Packets) (KBytes) (KBytes) Weights atm_pvc_0_35 disabled early 25% 25% 25% 25% atm_pvc_8_35 enabled early 25% 25% 25% 25% =>...
Page 451: Ipqos Ef Config
IPQoS Commands ipqos ef config Configure the IPQoS Expedited Forwarding (EF) timer for an interface. SYNTAX: ipqos ef config intf = <string> [state = <{disabled | enabled}>] [timeout = <number{100-10000}>] [mtu = <number{68-65535}>] where: intf The name of the IP interface. REQUIRED state Enable or disable the IPQoS EF timer for the interface.
Page 452: Ipqos Ef List
IPQoS Commands ipqos ef list Display the IPQoS EF timers. SYNTAX: ipqos ef list EXAMPLE: =>ipqos ef list Interface State Timeout (ms) (bytes) loop disabled 1000 65535 Rt_PPPoA2 enabled 1000 1500 eth0 disabled 1000 1500 => RELATED COMMANDS: ipqos ef config Configure the IPQoS Expedited Forwarding (EF) timer for an interface.
Page 453: Ipqos Ef Stats
IPQoS Commands ipqos ef stats Display the IPQoS EF timer statistics. SYNTAX: ipqos ef stats EXAMPLE: =>ipqos ef stats Interface State Remain (ms) loop active Rt_PPPoA2 active eth0 disabled => RELATED COMMANDS: ipqos ef config Configure the IPQoS Expedited Forwarding (EF) timer for an interface. ipqos ef list Display the IPQoS EF timers.
Page 454: Ipqos Queue Clear
IPQoS Commands ipqos queue clear Clear the IPQoS statistics. SYNTAX: ipqos queue clear EXAMPLE: =>ipqos queue stats Name Queue # packets # packets # packets # packets # packets Marking added marked removed dropped replaced PVC_1 0 1240 1240 1345 1345 =>ipqos queue clear =>ipqos queue stats...
Page 455: Ipqos Queue Config
IPQoS Commands ipqos queue config Modify the IPQoS subqueue configuration. SYNTAX: ipqos queue config dest = <string> queue = <number{0-5}> [propagate = <{disabled | enabled}>] [ecnmarking = <{disabled | enabled}>] [ackfiltering = <{disabled | enabled}>] [maxpackets = <number{0-250}>] [maxbytes = <number{0-128}>] [respackets = <number{0-250}>] [resbytes = <number{0-128}>] [hold = <number>]...
Page 456 IPQoS Commands maxbytes A number between 0 and 128. OPTIONAL Represents the maximum size in kilobytes of this queue. The default is for the Real time queue and for the other queues. Note 0 means that a maximum size is not enforced. respackets A number between 0 and 250.
Page 457: Ipqos Queue List
IPQoS Commands ipqos queue list Display the IPQoS subqueue configuration. SYNTAX: ipqos queue list [dest = <string}>] where: dest The destination interface for the IPQoS queues instantiation. OPTIONAL This is an ATM phonebook entry. Note If not specified, the IPQoS subqueue configuration for all the interfaces will be shown.
Page 458: Ipqos Queue Stats
IPQoS Commands ipqos queue stats Show the IPQoS subqueue statistics. SYNTAX: ipqos queue stats [dest = <string}>] where: dest The destination interface for the IPQoS queues instantiation. OPTIONAL This is an ATM phonebook entry. Note If not specified, the IPQoS subqueue statistics for all the interfaces will be shown.
Page 459: Label Commands
Label Commands Label Commands Introduction This chapter describes the commands of the label command group. Contents This chapter covers the following commands: label add Create a new label. label delete Delete a label. label flush Flush all labels. label list Display the labels.
Page 460: Label Add
Label Commands label add Create a new label. SYNTAX: label add name = <string> where: name The name of the label to be added. REQUIRED EXAMPLE: =>label list Name Class Bidirect Inherit Tosmark Type Value Ttlover Trace DSCP overwrite dscp defclass disabled disabled disabled tos disabled 0...
Page 461: Label Delete
Label Commands label delete Delete a label. SYNTAX: label delete name = <string> [force = <{disabled | enabled}>] where: name The name of the label to be deleted. REQUIRED force Force delete and cleanup references even when the label is still in use (enabled) or not OPTIONAL (disabled).
Page 462: Label Flush
Label Commands label flush Flush all labels. The flush command does not impact previously saved configurations. SYNTAX: label flush E-DOC-CTC-20060414-0002 v1.0...
Page 463: Label List
Label Commands label list Display the labels. SYNTAX: label list [name = <string>] where: name The name of the label to be displayed. OPTIONAL Note If not specified, all the labels will be displayed. EXAMPLE: =>label list Name Class Bidirect Inherit Tosmark Type Value...
Page 464: Label Modify
Label Commands label modify Modify a label configuration. SYNTAX: label modify name = <string> [classification = <{ignore | overwrite | increase}>] [defclass = <number{0-15} | dscp | default>] [ackclass = <number{0-15} | defclass | prioritize>] [bidirectional = <{disabled | enabled}>] [inheritance = <{disabled | enabled}>] [tosmarking = <{disabled | enabled}>] [tos = <number{0-255}>]...
Page 465 Label Commands bidirectional The label applies to the initiator stream, the returning stream (the current OPTIONAL connection) as well as to the child connections (enabled) or not (disabled). The default is disabled. inheritance The label will be copied to all child connection streams in the same direction OPTIONAL (enabled) or not (disabled).
Page 466: Label Chain Add
Label Commands label chain add Add a new label chain. SYNTAX: label chain add chain = <string> where: chain The name of the chain to be added. REQUIRED EXAMPLE: =>label chain list Chains ====== Name Description ------------------------------------------------- routing_labels system rt_user_labels user rt_default_labels user...
Page 467: Label Chain Delete
Label Commands label chain delete Delete a label chain. SYNTAX: label chain delete chain = <string> where: chain The name of the chain to be deleted. REQUIRED EXAMPLE: =>label chain list Chains ====== Name Description ------------------------------------------------- routing_labels system rt_user_labels user rt_default_labels user qos_labels...
Page 468: Label Chain Flush
Label Commands label chain flush Flush all label chains. SYNTAX: label chain flush E-DOC-CTC-20060414-0002 v1.0...
Page 469: Label Chain List
Label Commands label chain list Display a list of chains. SYNTAX: label chain list [format = <{pretty | cli}>] where: format Select the output format of the list. OPTIONAL Choose between: pretty: the configuration is shown as intuitive output in clear text. cli: the configuration is shown via the CLI commands configuration.
Page 470: Label Rule Add
Label Commands label rule add Add a label rule. SYNTAX: label rule add chain = <chain name> [index = <number>] [name = <string>] [clink = <chain name>] [srcintf [!]= <string>] [srcip [!]= <{ip address | private}>] [dstip [!]= <{ip address | private}>] [serv [!]= <{service name}>] [log = <{disabled | enabled}>] [state = <{disabled | enabled}>]...
Page 471 Label Commands EXAMPLE: =>label rule list Rules (flags: C=Constant, D=Dynamic, E=Enable, L=Log) ===== Chain Flags Rule -------------------------------------------------------------------------------------------------- routing_labels : link rt_user_labels : link rt_default_labels qos_labels : link qos_user_labels : link qos_default_labels qos_default_labels : VoIP sip *.* > *.* : VoIP h323 *.* >...
Page 472 Label Commands RELATED COMMANDS: label rule delete Delete a label rule. label rule list Display a list of label rules. E-DOC-CTC-20060414-0002 v1.0...
Page 473: Label Rule Delete
Label Commands label rule delete Delete a label rule. SYNTAX: label rule delete chain = <string> index = <number> where: chain The name of the chain in which a rule must be deleted. REQUIRED index The index number of the rule in the chain. REQUIRED Use the command :label rule list to obtain the index number of the applicable rule.
Page 474 Label Commands RELATED COMMANDS: label rule add Add a label rule. label rule list Display a list of label rules. E-DOC-CTC-20060414-0002 v1.0...
Page 475: Label Rule Flush
Label Commands label rule flush Flush all label rules. The chains themselves are not removed. The flush command does not impact previously saved configurations. SYNTAX: label rule flush [chain = <string>] where: chain The name of the chain to be flushed. OPTIONAL Note If not specified, all the rules for all the chains are flushed.
Page 476: Label Rule List
Label Commands label rule list Display a list of label rules. SYNTAX: label rule list [chain = <string>] [format = <{pretty | cli}>] where: chain The name of the chain for which the rules must be listed. OPTIONAL Note If not specified, all rules for all chains are shown. format Select the output format of the list.
Page 477 Label Commands EXAMPLE: =>label rule list format=cli :label rule add chain=qos_default_labels index=1 serv=sip log=disabled state=enabled label=VoIP :label rule add chain=qos_default_labels index=2 serv=h323 log=disabled state=enabled label=VoIP :label rule add chain=qos_default_labels index=3 serv=telnet log=disabled state=enabled label=Interactive :label rule add chain=qos_default_labels index=4 serv=smtp log=disabled state=enabled label=Interactive :label rule add chain=qos_default_labels index=5 serv=imap4-ssl log=disabled state=enabled label=Interactive...
Page 478: Label Rule Modify
Label Commands label rule modify Modify a label rule. SYNTAX: label rule modify chain = <chain name> index = <number> [newindex = <number>] [name = <string>] [clink = <chain name>] [srcintf [!]= <string>] [srcip [!]= <{ip address | private}>] [dstip [!]= <{ip address | private}>] [serv [!]= <{service name}>] [log = <{disabled | enabled}>] [state = <{disabled | enabled}>]...
Page 479: Label Rule Debug Clear
Label Commands label rule debug clear Clear the label rule statistics. SYNTAX: label rule debug clear [chain = <string>] [index = <number>] where: chain The name of the chain in which the rule is to be found. OPTIONAL Note If not specified, the statistics for all the rules in all chains will be cleared. index The index number (determined by the position) of the rule in the chain.
Page 480: Label Rule Debug Stats
Label Commands label rule debug stats Display the label rule statistics. SYNTAX: label rule debug stats [chain = <string>] [index = <number>] where: chain The name of the chain for which the statistics must be shown. OPTIONAL Note If not specified, the statistics for the rules applicable to all chains are shown. index The index number of the rule for which the statistics must be shown.
Page 481: Label Rule Debug Traceconfig
Label Commands label rule debug traceconfig Display or modify the rule trace configuration. SYNTAX: label rule debug traceconfig [trace = <{disabled | enabled}>] where: trace Disable or enable rule traces. OPTIONAL The default is disabled. EXAMPLE: =>label rule debug traceconfig :label rule debug traceconfig state=disabled =>...
Page 482 Label Commands E-DOC-CTC-20060414-0002 v1.0...
Page 483: Language Commands
Language Commands Language Commands Introduction This chapter describes the commands of the language command group. Contents This chapter covers the following commands: language config Select a language. language delete Delete one or all language archives. language list List the available language archives. E-DOC-CTC-20060414-0002 v1.0...
Page 484: Language Config
Language Commands language config Select a language. SYNTAX: language config [language = <string>] [complete = <{yes | no}>] where: language Language code: OSI language code (2 chars) for language. OPTIONAL Example: for english. complete Enable translation for expert pages. OPTIONAL The default is yes.
Page 485: Language Delete
Language Commands language delete Delete one or all language archives. SYNTAX: language delete [file = <string>] [all = <{yes | no}>] where: file The filename of the language archive to be removed. OPTIONAL Remove all languages archives (yes) or not (no). OPTIONAL The default is no.
Page 486: Language List
Language Commands language list List the available language archives. SYNTAX: language list EXAMPLE: =>language list CODE LANGUAGE VERSION FILENAME en* English 5.3.0.10.0 <system> => The currently selected language is indicated by a “*” next to the OSI language code. RELATED COMMANDS: language config Select a language.
Page 487: Mbus Commands
MBUS Commands MBUS Commands Introduction This chapter describes the commands of the mbus command group. Contents This chapter covers the following commands: mbus config Modify mbus parameters. mbus client config Modify client parameters. mbus client exec Execute mbus command. mbus client register Register cli client to mbus.
Page 488: Mbus Config
MBUS Commands mbus config Modify mbus parameters. SYNTAX: mbus config [autoload = <{disabled | enabled}>] where: autoload Enable or disable autoload object tree at boot time. OPTIONAL The default is enabled. E-DOC-CTC-20060414-0002 v1.0...
Page 489: Mbus Client Config
MBUS Commands mbus client config Modify client parameters. SYNTAX: mbus client config [writelock = <{enabled | disabled}>] [wlgetimeout = <number>] [wlidletimeout = <number>] [path = <quoted string>] [type = <idpath | keypath>] where: writelock Enable or disable mbus writelock. OPTIONAL The default is enabled.
Page 490: Mbus Client Exec
MBUS Commands mbus client exec Execute mbus command. SYNTAX: mbus client exec cmd = <{addobject | deleteobject | getparamattributes | getparamcount | getparamnames | getparamvalues | getpath | setparamvalue}> [param = <quoted string>] [value = <quoted string>] [gettype = <{object | parameter | path}>] [depth = <number>] [processcmd = <{disabled | enabled}>] [readcommitted = <{disabled | enabled}>]...
Page 491 MBUS Commands RELATED COMMANDS: mbus client config Modify client parameters. mbus client register Register cli client to mbus. mbus client test Test functionality invoked. E-DOC-CTC-20060414-0002 v1.0...
Page 492: Mbus Client Register
MBUS Commands mbus client register Register cli client to mbus. SYNTAX: mbus client register RELATED COMMANDS: mbus client config Modify client parameters. mbus client exec Execute mbus command. mbus client test Test functionality invoked. E-DOC-CTC-20060414-0002 v1.0...
Page 493: Mbus Client Test
MBUS Commands mbus client test Test functionality invoked. SYNTAX: mbus client test [path = <quoted string>] [type = <{idpath | keypath}>] where: path Fully qualified mbus path. OPTIONAL type Path type. OPTIONAL Choose between: idpath keypath. The default is idpath. EXAMPLE: =>mbus client test pool name...
Page 494: Mbus Debug Stats
MBUS Commands mbus debug stats Display mbus statistics. SYNTAX: mbus debug stats RELATED COMMANDS: mbus debug traceconfig Modify mbus trace settings. E-DOC-CTC-20060414-0002 v1.0...
Page 495: Mbus Debug Traceconfig
MBUS Commands mbus debug traceconfig Modify mbus trace settings. SYNTAX: mbus debug traceconfig [level = <number{0-4}>] where: level A number between 0 and 4. OPTIONAL Represents the mbus trace level. RELATED COMMANDS: mbus debug stats Display mbus statistics. E-DOC-CTC-20060414-0002 v1.0...
Page 496: Mbus Listobjects
MBUS Commands mbus listobjects Display the object instances. SYNTAX: mbus listobjects [path = <quoted string>] [type = <{idpath | keypath}>] [output = <{list | tree}>] [expand = <{disabled | enabled}>] where: path Fully qualified mbus path to list. OPTIONAL type Path type.
Page 497: Mbus Listtypes
MBUS Commands mbus listtypes Display the registered objecttypes. SYNTAX: mbus listtypes [path = <quoted string>] [expand = <{disabled | enabled}>] where: path Fully qualified mbus path to list. OPTIONAL expand Enable or disable details. OPTIONAL The default is disabled. EXAMPLE: =>mbus listtypes - root + InternetGatewayDevice...
Page 498: Mbus Loadobjects
MBUS Commands mbus loadobjects Load object instances of registered objecttypes. SYNTAX: mbus loadobjects [path = <quoted string>] [type = <{idpath | keypath}>] where: path Fully qualified mbus path. OPTIONAL type Path type. OPTIONAL Choose between: idpath keypath. The default is idpath. RELATED COMMANDS: mbus unloadobjects Unload object instances.
Page 499: Mbus Unloadobjects
MBUS Commands mbus unloadobjects Unload object instances. SYNTAX: mbus unloadobjects [path = <quoted string>] [type = <{idpath | keypath}>] where: path Fully qualified mbus path. OPTIONAL type Path type. OPTIONAL Choose between: idpath keypath. The default is idpath. RELATED COMMANDS: mbus loadobjects Load object instances of registered objecttypes.
Page 500 MBUS Commands E-DOC-CTC-20060414-0002 v1.0...
Page 501: Memm Commands
MEMM Commands MEMM Commands Introduction This chapter describes the commands of the memm command group. Contents This chapter covers the following commands: memm debug lock Modify lock trace settings. traceconfig memm debug traceconfig Modify memm trace settings. memm listobjects Display objects. memm stats Display memm statistics.
Page 502: Memm Debug Lock Traceconfig
MEMM Commands memm debug lock traceconfig Modify lock trace settings. SYNTAX: memm debug lock traceconfig [level = <number{0-4}>] [name = <string>] where: level A number between 0 and 4. OPTIONAL Represents the memm trace level. name Application name filter for lock traces (empty displays all lock OPTIONAL traces).
Page 503: Memm Debug Traceconfig
MEMM Commands memm debug traceconfig Modify memm trace settings. SYNTAX: memm debug traceconfig [level = <number{0-4}>] where: level A number between 0 and 4. OPTIONAL Represents the memm trace level. E-DOC-CTC-20060414-0002 v1.0...
Page 504: Memm Listobjects
MEMM Commands memm listobjects Display objects. SYNTAX: memm listobjects [name = <quoted string>] where: name Select typename(s) to list (supports partial typename). OPTIONAL E-DOC-CTC-20060414-0002 v1.0...
Page 505: Memm Stats
MEMM Commands memm stats Display memm statistics. SYNTAX: memm stats [name = <quoted string>] where: name Select typename(s) to list (supports partial typename). OPTIONAL EXAMPLE: =>memm stats pool name bytes cur,max,avail (max.%) count cur,max,avail ref cur,max,avail --------- ---------------------------- ------------------- ----------------- memm_pooldesc 1196, 1196,...
Page 506 MEMM Commands EXAMPLE: =>memm stats pool name bytes cur,max,avail (max.%) count cur,max,avail cur,max,avail ------------- --------------------------- ------------------- memm_pooldesc 1196, 1196, 1300 ( 92%) dynstr_pool 120 ( 60%) mbus_llist 2460, 2532, 4920 ( 51%) 205, 211, mbus_dynstr 2316, 2424, 4920 ( 49%) 193, 202, - strings buffer...
Page 507: Mlp Commands
MLP Commands MLP Commands Introduction This chapter describes the commands of the mlp command group. Contents This chapter covers the following commands: mlp flush Flush all the Multi-Level access Policies (MLP) structures. mlp import Import all the scores. mlp debug export Export all the scores.
Page 508: Mlp Flush
MLP Commands mlp flush Flush all the Multi-Level access Policies (MLP) structures. SYNTAX: mlp flush E-DOC-CTC-20060414-0002 v1.0...
Page 509: Mlp Import
MLP Commands mlp import Import all the scores. SYNTAX: mlp import [trace = <{disabled | enabled | full}>] where: trace Select the import trace level. OPTIONAL Choose between: disabled enabled full. The default is disabled. RELATED COMMANDS: mlp debug export Export all the scores.
Page 510: Mlp Debug Export
MLP Commands mlp debug export Export all the scores. SYNTAX: mlp debug export RELATED COMMANDS: mlp import Import all the scores. E-DOC-CTC-20060414-0002 v1.0...
Page 511: Mlp Debug Stats
MLP Commands mlp debug stats Display MLP statistics. SYNTAX: mlp debug stats EXAMPLE: =>mlp debug stats Roles (cur/free/max) : 8/7/15 Privileges (cur/free/max) : 35/25/60 ListItems (cur/free/max) : 31/119/150 => E-DOC-CTC-20060414-0002 v1.0...
Page 512: Mlp Debug Traceconfig
MLP Commands mlp debug traceconfig Modify the MLP trace settings. SYNTAX: mlp debug traceconfig [trace = <{disabled | enabled | full}>] where: trace Select the trace level. OPTIONAL Choose between: disabled enabled full. The default is disabled. EXAMPLE: =>mlp debug traceconfig mlp trace: disabled =>...
Page 513: Mlp Privilege Add
MLP Commands mlp privilege add Add a privilege. SYNTAX: mlp privilege add name = <quoted string> type = <{access | service}> [descr = <quoted string>] where: name The name of the new privilege. REQUIRED Note The maximum number of privileges is 60. type Select the privilege type.
Page 514 MLP Commands RELATED COMMANDS: mlp privilege delete Delete a privilege. mlp privilege list Display the privileges. E-DOC-CTC-20060414-0002 v1.0...
Page 515: Mlp Privilege Addzone
MLP Commands mlp privilege addzone Add a zone to a privilege. Only one zone can be added at a time to a privilege. If multiple zones need to be added, the command :mlp privilege addzone must be executed for each zone to be added. SYNTAX: mlp privilege addzone name = <string>...
Page 516: Mlp Privilege Config
MLP Commands mlp privilege config Modify a privilege. SYNTAX: mlp privilege config name = <string> [descr = <quoted string>] [score = <{hex-word}[:{hex-word}] ex: 'a12:c30f'>] where: name The name of the privilege to be modified. REQUIRED descr Set the privilege description. OPTIONAL Note The maximum length is 63 characters.
Page 517: Mlp Privilege Delete
MLP Commands mlp privilege delete Delete a privilege. SYNTAX: mlp privilege delete name = <string> where: name The name of the privilege to be deleted. REQUIRED EXAMPLE: =>mlp privilege list type=access Privilege (type) Description ---------------------------- anyaccess (access) All access privileges granted AP1 (access) LAN _Local_all AP2 (access) LAN_Local with all secured channels AP3 (access) LAN_Local with all channels &...
Page 518: Mlp Privilege List
MLP Commands mlp privilege list Display the privileges. SYNTAX: mlp privilege list [name = <string>] [type = <{access | service}>] [verbose = <{minimal | medium | all}>] where: name The name of the privilege to be listed. OPTIONAL Note If not specified, all the privileges will be shown. type Select the privilege type to be shown.
Page 519 MLP Commands RELATED COMMANDS: mlp privilege delete Add a privilege. mlp privilege delete Delete a privilege. E-DOC-CTC-20060414-0002 v1.0...
Page 520: Mlp Privilege Removezone
MLP Commands mlp privilege removezone Remove a zone from a privilege. Only one zone can be removed at a time from a privilege. If multiple zones need to be removed, the command :mlp privilege removezone must be executed for each zone to be removed. SYNTAX: mlp privilege removezone name = <string>...
Page 521: Mlp Role Add
MLP Commands mlp role add Add a role. SYNTAX: mlp role add name = <quoted string> parent = <string> [descr = <quoted string>] where: name The name of the new role. REQUIRED Note The maximum number of roles is 15. parent The name of the parent role.
Page 522: Mlp Role Addpriv
MLP Commands mlp role addpriv Add a privilege to a role. SYNTAX: mlp role addpriv name = <string> access = <string> service = <string> where: name The name of the role. REQUIRED access The name of the access privilege to be added. REQUIRED service The name of the service privilege to be added.
Page 523: Mlp Role Config
MLP Commands mlp role config Modify the role. SYNTAX: mlp role config name = <string> [parent = <string>] [descr = <quoted string>] where: name The name of the role to be configured. REQUIRED parent The name of the parent role. OPTIONAL descr The role description.
Page 524: Mlp Role Delete
MLP Commands mlp role delete Delete a role. SYNTAX: mlp role delete name = <string> where: name The name of the role to be deleted. REQUIRED EXAMPLE: =>mlp role list Role (parent) Description ------------------------- root (-) The superuser SuperUser (root) Any service and any access from LAN/WAN/LOCAL TechnicalSupport (SuperUser) Any service and any channels from WAN Administrator (TechnicalSupport) Any service and any access from LAN/Local origin only PowerUser (Administrator) GUI(Service/overview page)via http/https from LAN origin...
Page 525: Mlp Role List
MLP Commands mlp role list Display the roles. SYNTAX: mlp role list [name = <string>] [verbose = <{minimal | medium | all}>] where: name The name of the role to be listed. OPTIONAL Note If not specified, all the roles will be listed. verbose Limit the output list.
Page 526: Mlp Role Removepriv
MLP Commands mlp role removepriv Remove a privilege from a role. SYNTAX: mlp role removepriv name = <string> access = <string> [service = <string>] where: name The name of the role. REQUIRED access The name of the access privilege to be deleted. REQUIRED service The name of the service privilege to be deleted.
Page 527: Nat Commands
NAT Commands NAT Commands Introduction This chapter describes the commands of the nat command group. Contents This chapter covers the following commands: nat config Display/modify global NAT configuration options. nat flush Flush the current NAT configuration. nat ifconfig Modify address translation on an IP interface. nat iflist Display the address translation configuration on all the interfaces.
Page 528: Nat Config
NAT Commands nat config Display/modify global NAT configuration options. SYNTAX: nat config [trace = <{disabled | enabled}>] where: trace Enable or disable traces. REQUIRED The default is disabled. EXAMPLE: =>nat config NAT traces : disabled =>nat config trace=enabled =>nat config NAT traces : enabled =>...
Page 529: Nat Flush
NAT Commands nat flush Flush the current NAT configuration. SYNTAX: nat flush E-DOC-CTC-20060414-0002 v1.0...
Page 530: Nat Ifconfig
Address translation is disabled. enabled: Address translation is enabled. transparent: An inside address is translated into the same outside IP address. In fact, no translation happens and the IP packets passing through the SpeedTouch™ remain untouched. The default is disabled. EXAMPLE: =>nat iflist...
Page 531: Nat Iflist
NAT Commands nat iflist Display the address translation configuration on all the interfaces. SYNTAX: nat iflist EXAMPLE: =>nat iflist Interface loop disabled Internet enabled RtPPPoE_ppp enabled LocalNetwork transparent => RELATED COMMANDS: nat ifconfig Modify address translation on an IP interface. E-DOC-CTC-20060414-0002 v1.0...
Page 532: Nat Mapadd
NAT Commands nat mapadd Add an address mapping to a Network Address Translation (NAT) enabled interface. SYNTAX: nat mapadd intf = <string> [type = <{napt | nat}>] [outside_addr = <ip-range>] [inside_addr = <ip-range>] [access_list = <ip-range>] [foreign_addr = <ip-range>] [protocol = <{supported IP protocol} or number>] [outside_port = <port-range>] [inside_port = <port-range>] [mode = <{auto | inbound | outbound}>]...
Page 533 NAT Commands access_list The range of inside addresses to which the mapping is restricted. OPTIONAL This parameter is used for outbound traffic only. Represents the list of inside IP addresses (LAN devices) allowed to make use of this map. Allowed values are: An IP address (A.B.C.D or A.D, meaning A.0.0.D).
Page 534 NAT Commands mode The mode to create the portmap. OPTIONAL Choose between: auto inbound outbound. The standard is auto. EXAMPLE: =>nat maplist Idx Type Interface Outside Address Inside Address 1 NAPT eth0 any:80 127.0.0.1:8080 2 NAPT eth0 any:1080 127.0.0.1:8080 3 NAPT eth0 any:8080 127.0.0.1:8080 =>nat mapadd intf=myPPP_ppp type=napt outside_addr=100.100.100.1 access_list=10.0.0.0/24...
Page 535: Nat Mapdelete
NAT Commands nat mapdelete Delete an address mapping from a NAT enabled interface. SYNTAX: nat mapdelete intf = <string> index = <number> where: intf The IP interface name. REQUIRED index The map index. REQUIRED Use the command :nat maplist to obtain a list of the mapindexes. EXAMPLE: =>nat maplist Idx Type Interface...
Page 536: Nat Maplist
NAT Commands nat maplist Display the address mapping for a NAT enabled interface. SYNTAX: nat maplist [intf = <string>] [expand = <{disabled | enabled}>] where: intf The IP interface name. OPTIONAL Note If not specified, the address mapping for all the NAT enabled interfaces will be shown.
Page 537: Nat Tmpladd
NAT Commands nat tmpladd Add an address mapping template. SYNTAX: nat tmpladd [intf = <string>] [group = <{wan|local|lan|tunnel|dmz|guest} or number>] [timeout = <number{0-65535}>] [type = <{napt | nat}>] outside_addr = <ip-range> [inside_addr = <ip-range>] [access_list = <ip-range>] [foreign_addr = <ip-range>] [protocol = <{supported IP protocol} or number>] [outside_port = <port-range>] [inside_port = <port-range>]...
Page 538 NAT Commands inside_addr The inside (typically private) IP address. OPTIONAL for NAT maps Inbound: Represents the address(es) to be used as destination address and NAPT after translation. maps. Outbound: This map will only apply if the source IP address is part of the inside address(es).
Page 539 NAT Commands outside_port The outside port number or range (only for maps of type napt). OPTIONAL for NAPT map. For a NAPT map: Represents the range of TCP/UDP ports to be used as dynamic port REQUIRED for range during the NAPT process. port-shifting map.
Page 540: Nat Tmpldelete
NAT Commands nat tmpldelete Delete an address mapping template. SYNTAX: nat tmpldelete index = <number> where: index The index of the address mapping template to be deleted. REQUIRED Use the command :nat tmpllist to view the address mapping templates. EXAMPLE: =>nat tmpllist Idx Type Interface Ifgroup...
Page 541: Nat Tmpllist
NAT Commands nat tmpllist Display the address mapping templates. SYNTAX: nat tmpllist [expand = <{disabled | enabled}>] where: expand Enable or disable expanded listing. OPTIONAL The default is disabled. EXAMPLE: =>nat tmpllist Idx Type Interface Ifgroup Outside Address Inside Address 1 NAPT any 100.200.100.1 unmapped...
Page 542: Nat Tmplinst
NAT Commands nat tmplinst Instantiate address mapping templates for a given dynamic address. SYNTAX: nat tmplinst intf = <string> addr_index = <ip-address> dynamic_addr = <ip-address> where: intf The IP interface name. REQUIRED addr_index The outside IP address index/key to instantiate for. REQUIRED dynamic_addr The dynamic address to substitute the index/key with.
Page 543: Ppp Commands
PPP Commands PPP Commands Introduction This chapter describes the commands of the ppp command group. Contents This chapter covers the following commands: ppp flush Flush all PPP interfaces. ppp ifadd Create a new PPP interface. ppp ifattach Attach a PPP interface. ppp ifconfig Configure a PPP interface.
Page 544: Ppp Flush
PPP Commands ppp flush Flush all PPP interfaces. The flush command does not impact previously saved configurations. SYNTAX: ppp flush E-DOC-CTC-20060414-0002 v1.0...
Page 545: Ppp Ifadd
PPP Commands ppp ifadd Create a new PPP interface. SYNTAX: ppp ifadd intf = <string> where: intf The name for the new PPP interface. REQUIRED Note If not specified, the destination parameter must be specified. In this case the name of the destination will double as interface name. EXAMPLE: =>ppp iflist Internet: dest : RELAY...
Page 546: Ppp Ifattach
PPP Commands ppp ifattach Attach a PPP interface. SYNTAX: ppp ifattach intf = <string> where: intf The name of the PPP interface to be attached. REQUIRED EXAMPLE: =>ppp iflist Internet: dest : RELAY [00:00:00] Retry : 10 mode = IP routing flags = echo magic accomp restart mru addr savepwd demanddial dns metric = 0 mru = 1492...
Page 547 PPP Commands RELATED COMMANDS: ppp ifdetach Detach a PPP interface. E-DOC-CTC-20060414-0002 v1.0...
Page 548: Ppp Ifconfig
PPP Commands ppp ifconfig Configure a PPP interface. The interface to be configured must not be connected at the time of configuration. If this should be the case, use the command :ppp ifdetach before using the command :ppp ifconfig. SYNTAX: ppp ifconfig intf = <string>...
Page 549 The access concentrator is on this side of the PPPoE connection. OPTIONAL Choose between: enabled: the PPP connection is terminated on the Access Concentrator (here the SpeedTouch™ itself) disabled: the SpeedTouch™ is PPP client. The default is disabled. auth Select the authentication protocol. OPTIONAL Choose between: pap: Password Authentication Protocol (PAP) authentication will be forced.
Page 550 The IP address of the primary DNS server. OPTIONAL In case a primary DNS server is specified, the SpeedTouch™ will negotiate this IP address with the remote side. Note If not specified, the SpeedTouch™ will accept any IP address.
Page 551 PPP Commands idletrigger Consider the link being idle if no traffic is sent and/or received during the idle OPTIONAL time. Choose between: RxTx: The idle time period restarts when a packet is transmitted or received. Rx: The idle time period restarts when a packet is received. Transmitted packets are ignored.
Page 552: Ppp Ifdelete
PPP Commands ppp ifdelete Delete a PPP interface. SYNTAX: ppp ifdelete intf = <intfname> where: intf The name of the PPP interface to be deleted. REQUIRED EXAMPLE: =>ppp iflist Internet: dest : RELAY [00:00:00] Retry : 10 mode = IP routing flags = echo magic accomp restart mru addr savepwd demanddial dns metric = 0 mru = 1492...
Page 553: Ppp Ifdetach
PPP Commands ppp ifdetach Detach a PPP interface. SYNTAX: ppp ifdetach intf = <intfname> where: intf The name of the PPP interface to be detached. REQUIRED EXAMPLE: =>ppp iflist Internet: dest : RELAY [00:00:00] Retry : 10 mode = IP routing flags = echo magic accomp restart mru addr savepwd demanddial dns metric = 0 mru = 1492...
Page 554 PPP Commands RELATED COMMANDS: ppp ifattach Attach a PPP interface. E-DOC-CTC-20060414-0002 v1.0...
Page 555: Ppp Iflist
PPP Commands ppp iflist Display the PPP interfaces. SYNTAX: ppp iflist [intf = <intfname>] where: intf The name of the PPP interface. OPTIONAL Note If not specified, all PPP interfaces are shown. EXAMPLE INPUT/OUTPUT : =>ppp iflist Internet: dest : RELAY [00:00:00] Retry : 10 mode = IP routing...
Page 556: Ppp Ifscan
PPP Commands ppp ifscan Scan a PPPoE interface for available Access Concentrator and Service names. Use the command :ppp ifdetach for this interface before performing a scan on it. SYNTAX: ppp ifscan intf = <string> [time = <number{0-36000}>] where: intf The name of the PPPoE interface to be scanned.
Page 557: Ppp Rtadd
PPP Commands ppp rtadd Add a route to the routing table when the PPP link comes up. This route configuration will determine which local hosts are allowed to use this link and/or which remote destinations should be or should not be reachable. The interface must not be connected when a route configuration is added.
Page 558 PPP Commands EXAMPLE: =>ppp iflist Internet: dest : RELAY [00:00:00] Retry : 10 mode = IP routing flags = echo magic accomp restart mru addr savepwd demanddial dns metric = 0 mru = 1492 Tx inactivity = 1200s left = 0s auth = auto user = password =...
Page 559: Ppp Rtdelete
PPP Commands ppp rtdelete Delete the route for a PPP link. The interface must not be connected when a route configuration must be deleted. If the interface is connected, use the command :ppp ifdetach for this interface. SYNTAX: ppp rtdelete intf = <intfname>...
Page 560 PPP Commands EXAMPLE: =>ppp iflist Internet: dest : RELAY [00:00:00] Retry : 10 mode = IP routing flags = echo magic accomp restart mru addr savepwd demanddial dns metric = 0 mru = 1492 Tx inactivity = 1200s left = 0s auth = auto user = password =...
Page 561: Ppp Relay Flush
PPP Commands ppp relay flush Remove all Ethernet interfaces from the PPP relay agent list and terminate all sessions. The flush command does not impact previously saved configurations. SYNTAX: ppp relay flush E-DOC-CTC-20060414-0002 v1.0...
Page 562: Ppp Relay Ifadd
PPP Commands ppp relay ifadd Add an Ethernet interface to the PPP relay list. SYNTAX: ppp relay ifadd intf = <string> where: intf The Ethernet interface to be added to the PPP relay agent list. REQUIRED EXAMPLE: =>ppp relay iflist Interface HWaddr Status...
Page 563: Ppp Relay Ifconfig
PPP Commands ppp relay ifconfig Modify an ethernet interface from the PPP relay agent list. SYNTAX: ppp relay ifconfig intf = <string> hwaddr = <hardware-address> where: inft The ethernet intf to be added to the PPP relay agent list. REQUIRED hwaddr The hardware address (e.g.
Page 564: Ppp Relay Ifdelete
PPP Commands ppp relay ifdelete Delete an Ethernet interface from the PPP relay agent list. SYNTAX: ppp relay ifdelete intf = <string> where: intf The Ethernet interface to be deleted from the PPP relay agent list. REQUIRED EXAMPLE: =>ppp relay iflist Interface HWaddr Status...
Page 565: Ppp Relay Iflist
PPP Commands ppp relay iflist Display all Ethernet interfaces added to the PPP relay agent list. SYNTAX: ppp relay iflist where: intf The Ethernet interface to be added to the PPP relay agent list. REQUIRED EXAMPLE: =>ppp relay iflist Interface HWaddr Status ethoa_0_35...
Page 566: Ppp Relay Sesslist
PPP Commands ppp relay sesslist Add an Ethernet interface to the PPP relay list. SYNTAX: ppp relay ifadd intf = <string> where: intf The Ethernet interface to be added to the PPP relay agent list. REQUIRED E-DOC-CTC-20060414-0002 v1.0...
Page 567: Pptp Commands
PPTP Commands PPTP Commands Introduction This chapter describes the commands of the pptp command group. Contents This chapter covers the following commands: pptp ifadd Add a Point-to-Point Tunneling Protocol (PPTP) profile. pptp flush Flush the complete PPTP configuration. pptp list Show the current PPTP configuration.
Page 568: Pptp Ifadd
PPTP Commands pptp ifadd Add a Point-to-Point Tunneling Protocol (PPTP) profile. Backwards compatible with previous release, use profiles instead. SYNTAX: pptp ifadd dest = <string> [rate = <number{10-10000}>] [encaps = <{vcmux | nlpid}>] [ac = <{never | always | keep}>] where: dest The WAN destination for this PPTP tunnel.
Page 569: Pptp Flush
PPTP Commands pptp flush Flush the complete PPTP configuration. The flush command does not impact previously saved configurations. SYNTAX: pptp flush E-DOC-CTC-20060414-0002 v1.0...
Page 570: Pptp List
PPTP Commands pptp list Show the current PPTP configuration. SYNTAX: pptp list EXAMPLE: =>pptp list Dialstr Destination Encaps State User DIALUP_PPP3 default vcmux never CONNECTED (10.0.0.2) => E-DOC-CTC-20060414-0002 v1.0...
Page 571: Pptp Profadd
PPTP Commands pptp profadd Define a new PPTP profile. SYNTAX: pptp profadd name = <string> [qos = <string>] [encaps = <{vcmux | nlpid}>] [ac = <{never | always | keep}>] where: name The name of the new PPTP profile. REQUIRED The name of the qosbook entry, containing the settings for this profile.
Page 572: Pptp Profdelete
PPTP Commands pptp profdelete Delete a PPTP profile. SYNTAX: pptp profdelete name <string> where: name The name of the PPTP profile to be deleted. REQUIRED EXAMPLE: =>pptp proflist Profile Encaps Relay_PPP1 default nlpid always PPTPLink default vcmux never =>pptp profdelete name=PPTPLink =>pptp proflist Profile Encaps...
Page 573: Pptp Proflist
PPTP Commands pptp proflist Display all the current PPTP profiles. SYNTAX: pptp proflist EXAMPLE: =>pptp proflist Profile Encaps Relay_PPP1 default nlpid always PPTPLink default vcmux never => RELATED COMMANDS: pptp profadd Define a new PPTP profile. pptp profdelete Delete a PPTP profile. E-DOC-CTC-20060414-0002 v1.0...
Page 574 PPTP Commands E-DOC-CTC-20060414-0002 v1.0...
Page 575: Script Commands
Script Commands Script Commands Introduction This chapter describes the commands of the script command group. Scripting is not a general purpose mechanism but is only used in the autoPVC/ILMI mechanism. It is recommended not to change the default scripts. Contents This chapter covers the following commands: script add Add a line to a script.
Page 576: Script Add
Script Commands script add Add a line to a script. SYNTAX: script add name = <string> [index = <number>] command = <quoted string> where: name Name of the script in which a line must be added. REQUIRED index Line number OPTIONAL Note Use 0 to add a line.
Page 577: Script Delete
Script Commands script delete Delete a complete script or a line from a script. SYNTAX: script delete name = <string> [index = <number>] where: name Name of the script to be deleted. REQUIRED index Line number to be deleted. OPTIONAL Use the command :script list to view the line numbers.
Page 578: Script Flush
Script Commands script flush Flush all scripts. The flush command does not impact previously saved configurations. SYNTAX: script flush E-DOC-CTC-20060414-0002 v1.0...
Page 579: Script List
Script Commands script list Display a script or all scripts. SYNTAX: script list [name = <string>] where: name Name of the script to be listed. OPTIONAL Note If not specified, all the scripts are displayed. EXAMPLE Some of the default scripts are shown below: =>script list Script: autopvc_add_qos 0: qosbook add name _auto_$1_$2 class $3 tx_peakrate $4 tx_sustrate $5 tx_maxburst $6...
Page 580: Script Run
Script Commands script run Run a script. SYNTAX: script run name = <string> pars = <string> where: name Name of the script to be run. REQUIRED Use the command :script list to obtain the names of the different scripts. pars Parameters separated with comma.
Page 581: Service Commands
Service Commands Service Commands Introduction This chapter describes the commands of the service command group. Contents This chapter covers the following commands: service host assign Assign a host service to a LAN device. service host config Get/set global host service configuration options. service host add Add a host service.
Page 582: Service Host Assign
Service Commands service host assign Assign a host service to a LAN device. SYNTAX: service host assign name = <quoted string> [host = <ip-address>] [log = <{disabled|enabled}>] where: name The name of an existing host service. REQUIRED host The IP address of the LAN device. OPTIONAL Enable or disable logging.
Page 583: Service Host Config
Service Commands service host config Get/set global host service configuration options. SYNTAX: service host config [trace = <{disabled | enabled}>] where: trace Enable or disable traces. REQUIRED The default is disabled. EXAMPLE: =>service host config Service traces : disabled l=> E-DOC-CTC-20060414-0002 v1.0...
Page 584: Service Host Add
Service Commands service host add Add a host service. SYNTAX: service host add name = <quoted string> [mode = <{server | client | custom}>] where: name The name of the new host service. REQUIRED mode The service mode. OPTIONAL Choose between: server: The service is defined for server purposes.
Page 585: Service Host Delete
Service Commands service host delete Delete a host service. SYNTAX: service host delete name = <quoted string> where: name The name of the host service to be deleted. REQUIRED EXAMPLE: =>service host list Service Name Host User-Defined Mode --------------------------------------------------------------------------- Age of Empires unassigned server AIM Talk...
Page 586: Service Host Disable
Service Commands service host disable Disable a host service. SYNTAX: service host disable [name = <quoted string>] where: name The name of the host service to be disabled. OPTIONAL Note If not specified, all the host services will be disabled. EXAMPLE: =>service host list Service Name...
Page 587: Service Host Flush
Service Commands service host flush Flush all host services. SYNTAX: service host flush E-DOC-CTC-20060414-0002 v1.0...
Page 588: Service Host List
Service Commands service host list Display a list of host services. SYNTAX: service host list [name = <quoted string>] where: name The name of the host service to be listed. REQUIRED Note If not specified, all the host services will be listed. EXAMPLE: =>service host list Service Name...
Page 589: Service Host Stats
Service Commands service host stats Show the host service statistics. SYNTAX: service host stats EXAMPLE: =>service host stats Services : 113 of 150 in use. Service maps : 225 of 300 in use. Trigger ports: 0 of 25 in use. =>...
Page 590: Service Host Triggerlist
Service Commands service host triggerlist List all triggers. SYNTAX: service host triggerlist EXAMPLE: =>service triggerlist Triggerport Portrange Timeout ----------- --------- ------- => E-DOC-CTC-20060414-0002 v1.0...
Page 591: Service Host Rule Add
Service Commands service host rule add Create/define a host service portmap. SYNTAX: service host rule add name = <quoted string> [protocol = <{any|tcp|udp} or number>] [baseport = <supported UDP port | number>] portrange = <port-range> [triggerport = <supported UDP port | number>] [triggerprotocol = <{any|tcp|udp} or number>] where: name...
Page 592: Service Host Rule Delete
Service Commands service host rule delete Delete a host service portmap. SYNTAX: service host rule delete name = <quoted string> [protocol = <{any|tcp|udp} or number>] [baseport = <supported UDP port | number>] portrange = <port-range> [triggerport = <supported UDP port | number>] [triggerprotocol = <{any|tcp|udp} or number>] where: name...
Page 593: Service System Ifadd
Service Commands service system ifadd Add an interface group to the access list. SYNTAX: service system ifadd name = <string> group = <{wan|local|lan|tunnel|dmz|guest} or number> where: name The name of the system service for this access list. REQUIRED group The interface group for this access list. REQUIRED EXAMPLE: =>service system list name=SIPPBX expand=enabled...
Page 594: Service System Ifdelete
Service Commands service system ifdelete Delete an interface group from the access list. SYNTAX: service system ifdelete name = <string> group = <{wan|local|lan|tunnel|dmz|guest} or number> where: name The name of the system service for this access list. REQUIRED group The interface group for this access list. REQUIRED EXAMPLE: =>service system list name=SIPPBX expand=enabled...
Page 595: Service System Ipadd
Service Commands service system ipadd Add an IP address (range) to the access list. SYNTAX: service system ipadd name = <string> ip = <ip-range> where: name The name of the system service for this access list. REQUIRED The IP address (range) for this access list. REQUIRED EXAMPLE: =>service system list name=SIPPBX expand=enabled...
Page 596: Service System Ipdelete
Service Commands service system ipdelete Delete an IP address (range) from the access list. SYNTAX: service system ipdelete name = <string> ip = <ip-range> where: name The name of the system service for this access list. REQUIRED The IP address (range) for this access list. REQUIRED EXAMPLE: =>service system list name=SIPPBX expand=enabled...
Page 597: Service System List
Service Commands service system list Display the system services. SYNTAX: service system list [name = <string>] [expand = <{disabled | enabled}>] [dynamics = <{disabled | enabled}>] [members = <{disabled | enabled}>] where: name The name of the system service to be displayed. OPTIONAL Note If not specified, all the system services will be displayed.
Page 598 Service Commands EXAMPLE: =>service system list Idx Name Protocol SrcPort DstPort Group State --------------------------------------------------------------------------------- 1 DNS-C enabled 2 SNTP enabled 3 SLA_ICMP_PING icmp enabled 4 SLA_UDP_PING enabled 5 SLA_ICMP_TRRT icmp enabled 6 SLA_UDP_TRRT 33434 enabled 7 SYSLOG enabled 8 HTTP enabled 9 HTTPs enabled...
Page 599: Service System Mapadd
Service Commands service system mapadd Add a port map for a system service. SYNTAX: service system mapadd name = <{string}> intf = <{auto|loop|Internet|LocalNetwork}> port = <supported port or number> where: name The name of the system service for this map. REQUIRED intf The interface for this map.
Page 600: Service System Mapdelete
Service Commands service system mapdelete Delete a port map for a system service. SYNTAX: service system mapdelete name = <string> intf = <{auto|loop|Internet|LocalNetwork}> port = <supported port or number> where: name The name of the system service for this map. REQUIRED intf The interface for this map.
Page 601: Service System Modify
Service Commands service system modify Modify a system service. SYNTAX: service system modify name = <string> [state = <{disabled | enabled}>] [port = <supported port or number>] [srcintf = <string>] [log = <{disabled|enabled}>] [forward = <{disabled|enabled}>] where: name The name of the system service for this map. REQUIRED state Disable or enable this system service.
Page 602 Service Commands E-DOC-CTC-20060414-0002 v1.0...
Page 603: Snmp Commands
SNMP Commands SNMP Commands Introduction This chapter describes the commands of the snmp command group. Contents This chapter covers the following commands: snmp config Show/set global Simple Network Management Protocol (SNMP) parameters. snmp get Get from the supplied SNMP Object IDentifier (OID). snmp getnext GetNext from the supplied SNMP OID.
Page 604: Snmp Config
The default is Customer Premises. EXAMPLE: =>snmp config SNMP System Contact : Service Provider SNMP System Name : SpeedTouch SNMP System Location : Customer Premises All SNMP traps : ENABLED Delay, in secs before first trap is sent : 90 =>...
Page 605: Snmp Get
The Object Identifier. Object ID to get from ... must include the instance which is 0 OPTIONAL for scalar objects, for example .1.3.6.1.2.1.1.1.0 sysDescription. Note If not specified, the sysDescription OID .1.3.6.1.2.1.1.1.0 is assumed. Its value is SpeedTouch™. EXAMPLE: =>snmp get VB_octetStr .1.3.6.1.2.1.1.1.0 SpeedTouch™...
Page 606: Snmp Getnext
SNMP Commands snmp getnext GetNext from the supplied SNMP OID. SYNTAX: snmp getnext [ObjectId = <string>] where: ObjectID The Object Identifier. OPTIONAL Object ID to getnext from for example .1.3.6.1.2.1.1 system returns sysDescription. EXAMPLE: =>snmp getnext ObjectId=.1.3.6.1.2.1.1.4.0 VB_octetStr .1.3.6.1.2.1.1.5.0 Sascha =>...
Page 607: Snmp Walk
[ObjectId = <string>] where: ObjectID The Object Identifier. OPTIONAL Object ID to walk from for example .1.3.6.1.2.1.1 system walks the system group. EXAMPLE: =>snmp walk ObjectId=.1.3.6.1.2.1.1 VB_octetStr .1.3.6.1.2.1.1.1.0 SpeedTouch™ 620 VB_objId .1.3.6.1.2.1.1.2.0 .1.3.6.1.4.1.637.61.2 VB_timeTicks .1.3.6.1.2.1.1.3.0 2927636 VB_octetStr .1.3.6.1.2.1.1.4.0 Service Provider VB_octetStr .1.3.6.1.2.1.1.5.0...
Page 608: Snmp Community Add
SNMP Commands snmp community add Configure an SNMP community string to allow SNMP access over IP. SYNTAX: snmp community add securityname = <{RWCommunity | ROCommunity}> communityname = <password> where: securityname Configure access rights/restrictions control for the community name. REQUIRED Choose between: RWCommunity: read/write access rights ROCommunity: read only access rights.
Page 609: Snmp Community Delete
SNMP Commands snmp community delete Delete an SNMP community string to prevent SNMP access over IP. SYNTAX: snmp community delete securityname = <{RWCommunity | ROCommunity}> where: securityname Select the access rights/restrictions control for the community name to be REQUIRED deleted. Choose between: RWCommunity: read/write access rights ROCommunity: read only access rights.
Page 610: Snmp Community List
SNMP Commands snmp community list List all SNMP community strings in use for SNMP access over IP. SYNTAX: snmp community list EXAMPLE: =>snmp community list Read-write SNMP community name ***** Read-only SNMP community name ***** => RELATED COMMANDS: snmp community add Configure an SNMP community string to allow SNMP access over IP.
Page 611: Snmp Community Modify
SNMP Commands snmp community modify Modify an SNMP community string to allow SNMP access over IP. SYNTAX: snmp community modify securityname = <{RWCommunity | ROCommunity}> communityname = <password> where: securityname Configure access rights/restrictions control for the community name. REQUIRED Choose between: RWCommunity: read/write access rights ROCommunity: read only access rights.
Page 612: Snmp Ifadd
SNMP Commands snmp ifadd Create a new SNMP interface. SYNTAX: snmp ifadd intf = <string> dest = <string> where: intf The name for the new SNMP interface. REQUIRED dest The destination interface for this SNMP interface. REQUIRED EXAMPLE: =>snmp ifadd intf = new dest = Internet :snmp ifadd intf=new dest=Internet...
Page 613: Snmp Ifdelete
SNMP Commands snmp ifdelete Delete an SNMP interface. SYNTAX: snmp ifdelete intf = <string> where: intf The name of the SNMP interface. REQUIRED EXAMPLE: =>snmp ifdelete intf = new :snmp ifdelete intf=new => RELATED COMMANDS: snmp ifadd Create a new SNMP interface. snmp ifattach Attach an SNMP interface.
Page 614: Snmp Ifattach
SNMP Commands snmp ifattach Attach an SNMP interface. SYNTAX: snmp ifattach intf = <string> where: intf The name of the SNMP interface. REQUIRED EXAMPLE: =>snmp ifattach intf = Internet :snmp ifattach intf=Internet => RELATED COMMANDS: snmp ifadd Create a new SNMP interface. snmp ifdelete Delete an SNMP interface.
Page 615: Snmp Ifdetach
SNMP Commands snmp ifdetach Detach an SNMP interface. SYNTAX: snmp ifdetach intf = <string> where: intf The name of the SNMP interface. REQUIRED EXAMPLE: =>snmp ifdetach intf = Internet :snmp ifdetach intf=Internet => RELATED COMMANDS: snmp ifadd Create a new SNMP interface. snmp ifdelete Delete an SNMP interface.
Page 616: Snmp Ifconfig
SNMP Commands snmp ifconfig Modify an SNMP interface. SYNTAX: snmp ifconfig intf = <string> [securityname = <{RWCommunity | ROCommunity}>] [communityname = <password>] where: intf The name of the SNMP interface to configure. REQUIRED securityname Configure access rights/restrictions control for the community OPTIONAL name.
Page 617: Snmp Iflist
SNMP Commands snmp iflist Display the SNMP interfaces. SYNTAX: snmp iflist [intf = <string>] where: intf The name of an SNMP interface to configure. OPTIONAL E-DOC-CTC-20060414-0002 v1.0...
Page 618 SNMP Commands E-DOC-CTC-20060414-0002 v1.0...
Page 619: Sntp Commands
SNTP Commands SNTP Commands Introduction This chapter describes the commands of the Simple Network Time Protocol (SNTP) command group. Contents This chapter covers the following commands: sntp add Add a Network Time Protocol (NTP) server to the NTP server list. sntp config Modify/display the SNTP client configuration.
Page 620: Sntp Add
SNTP Commands sntp add Add a Network Time Protocol (NTP) server to the NTP server list. The internal SpeedTouch™ real time clock (SNTP client) will be synchronized with the NTP server. SYNTAX: sntp add [addr = <ip-address>] [name = <string>] [version = <number{1-4}>]...
Page 621: Sntp Config
SYNTAX: sntp config [enable = <{enabled | disabled}>] [poll = <number{1-60}>] where: enable Enable or disable the SpeedTouch™ SNTP client. OPTIONAL The default is enabled. poll A number between 1 and 60 (minutes). OPTIONAL Represents the time interval for the SNTP client to poll the configured NTP server and, if needed, (re-)synchronize its internal clock.
Page 622: Sntp Delete
SNTP Commands sntp delete Delete an NTP server from the NTP server list. SYNTAX: sntp delete [addr = <ip-address>] [name = <string>] where: addr The IP address of the NTP server to be removed from the list. OPTIONAL Note This parameter is optional in this respect that either an IP address or the name of an NTP server must be specified.
Page 623: Sntp Flush
SNTP Commands sntp flush Flush the NTP server list and the SNTP client configuration. SYNTAX: sntp flush E-DOC-CTC-20060414-0002 v1.0...
Page 624: Sntp List
Contacting...: The SpeedTouch™ SNTP client is trying to contact this NTP server. Unable to contact: The SpeedTouch™ SNTP client is unable to contact this NTP server. It may be down, or no end-to-end connectivity exists (no connection, no DSL,...). Synchronized: The SpeedTouch™ SNTP client was able to contact this NTP server. If required the internal clock has been synchronized with this NTP server.
Page 625: Software Commands
Software Commands Software Commands Introduction This chapter describes the commands of the software command group. Contents This chapter covers the following commands: software upgrade Reboot the modem to initiate the SW upgrade. software version Display the software version. E-DOC-CTC-20060414-0002 v1.0...
Page 626: Software Upgrade
Software Commands software upgrade Reboot the modem to initiate the SW upgrade. New software available on a remote LAN host will be uploaded to the modem. SYNTAX: software upgrade E-DOC-CTC-20060414-0002 v1.0...
Page 627: Software Version
Software Commands software version Display the software version. SYNTAX: software version E-DOC-CTC-20060414-0002 v1.0...
Page 628 Software Commands E-DOC-CTC-20060414-0002 v1.0...
Page 629: System Commands
Set/get the regional settings. system reboot Reboot the SpeedTouch™. system reset Reset the SpeedTouch™ to its factory or ISP defaults and reboot the device. system timedreboot Set or change a timed reboot for the SpeedTouch™. system debug autosave Autosave debugging commands system debug stats Show the SpeedTouch™...
Page 630: System Config
System Commands system config Set/change the system configuration parameters. For a good operation of UPnP and the discovery mechanism, it is highly recommended not to change the system configuration settings. SYNTAX: system config [upnp = <{disabled | enabled}>] [tr64 = <{disabled | enabled}>] [mdap = <{disabled | enabled}>] [drst = <{disabled | enabled}>] [led = <{green | red | orange | flash | off}>]...
Page 631 System Commands autosavedelay A number between 0 and 600. OPTIONAL Represents the autosave delay in seconds (0 for immediate save). EXAMPLE: =>system config upnp discovery : enabled TR-64 discovery : disabled mdap discovery : enabled drst support : disabled reset button : enabled digest authentication : enabled : enabled...
Page 632: System Flush
System Commands system flush Flush the current system configuration. The system password and the system config settings (dcache excluded) are flushed. The flush command does not impact previously saved configurations. SYNTAX: system flush EXAMPLE: =>system flush Security notification: Password changed, use 'saveall' to make it permanent. =>...
Page 633: System Locale
System Commands system locale Set/get the regional settings. SYNTAX: system locale [dec_symbol = <{, | .}>] [group_symbol = <{. | ,}>] [date_separator = <{/ | - | .}>] [date_format = <{iso | ddmmyyyy | ddmmyy | mmddyyyy | mmddyy}>] [time_format = <{iso | hmmss}>] [datetime_format = <{iso | date+time | time+date}>] [duration_format = <{dhmmss | hmmss}>] where:...
Page 634 System Commands time_format Set the time format. OPTIONAL Choose between: hmmss. The default is iso. Note h = hours; mm = minutes; ss = seconds. datetime_format Set the date-time format. OPTIONAL Choose between: date+time time+date. The default is date+time. duration_format Set the duration format.
Page 635: System Reboot
Reboot the SpeedTouch™. Non-saved configuration settings will be lost after reboot. SYNTAX: system reboot EXAMPLE: =>system reboot ..(lost session connectivity due to reboot) ..RELATED COMMANDS: system timedreboot Set or change a timed reboot for the SpeedTouch™.. E-DOC-CTC-20060414-0002 v1.0...
Page 636: System Reset
System Commands system reset Reset the SpeedTouch™ to its factory or ISP defaults and reboot the device. All user specific settings and all saved configuration changes are lost after reboot. SYNTAX: system reset factory yes/no = <{yes | no}> proceed no/yes = <{no | yes}>...
Page 637: System Timedreboot
System Commands system timedreboot Set or change a timed reboot for the SpeedTouch™. SYNTAX timedreboot [state = <{disabled|enabled}>] [time = <number{0-16384}>] [date = <string>] where: state Enable/Disable timed reboot. OPTIONAL The default is disabled. time Change default countdown time (Min).
Page 638: System Debug Autosave
System Commands system debug autosave Autosave debugging commands SYNTAX: system debug autosave [trace = <{disabled|enabled}>] where: trace Enable or disable autosave traces OPTIONAL E-DOC-CTC-20060414-0002 v1.0...
Page 639: System Debug Stats
Memory used by the CPU (first MB from the RAM) – not cached since it has to be realtime. Application memory: Memory used by the applications. min: The least amount of free memory detected during the uptime of the SpeedTouch™. E-DOC-CTC-20060414-0002 v1.0...
Page 640: System Ra Config
System Commands system ra config Configure Remote management access parameters. SYNTAX: system ra config [secure = <{disabled | enabled}>] [port = <number>] [timeout = <number>] where: secure Enable or disable https. OPTIONAL The default is enabled. port Set the destination port for remote access. OPTIONAL The default is 51003.
Page 641: System Rtc Synchronize
System Commands system rtc synchronize Do a SNTP update and synchronize the realtime clock. SYNTAX: system rtc synchronize E-DOC-CTC-20060414-0002 v1.0...
Page 642: System Rtc Settime
Set/get date, time, timezone, daylight savings time, uptime. When synchronization with an external NTP server via the SpeedTouch™ SNTP client fails, this command allows to manually configure its internal clock. In cases without regular synchronization, accurate realtime clock settings can not be guaranteed.
Page 643: Systemlog Commands
Systemlog Commands Systemlog Commands Introduction This chapter describes the commands of the systemlog command group. Contents This chapter covers the following commands: systemlog flush Flush all messages in the internal Syslog message buffer. systemlog show Show messages in the internal Syslog message buffer. systemlog send Send messages from the internal Syslog message buffer to a specified local or remote syslog server host.
Page 644: Systemlog Flush
Systemlog Commands systemlog flush Flush all messages in the internal Syslog message buffer. SYNTAX: systemlog flush E-DOC-CTC-20060414-0002 v1.0...
Page 645: Systemlog Show
672). Note If not specified, the messages of all the severities will be shown. hist Show messages over several SpeedTouch™ reboots (enabled) or show only messages OPTIONAL since latest startup (disabled). Note If not specified, only the recent messages will be shown.
Page 646: Systemlog Send
672). Note If not specified, the messages of all the severities will be shown. hist Show messages over several SpeedTouch™ reboots (disabled) or show only messages OPTIONAL since latest startup (enabled). Note If not specified, only the recent messages will be shown.
Page 647: Upgrade Commands
Upgrade Commands Upgrade Commands Introduction This chapter describes the commands of the upgrade command group. Contents This chapter covers the following commands: upgrade config Change the upgrade daemon configuration. upgrade start Start a new upgrade. upgrade debug traceconfig Enable/disable upgrade daemon tracing. upgrade debug sesslist Display the list of sessions.
Page 648: Upgrade Config
Upgrade Commands upgrade config Change the upgrade daemon configuration. SYNTAX: upgrade config [state = <{disabled|enabled}>] [protocol = <{tftp|ftp|http|https}>] where: state Set the upgrade daemon state to enabled or disabled. OPTIONAL The default is disabled. protocol The transfer protocol to be used for file download. OPTIONAL Choose between: tftp...
Page 649: Upgrade Start
Upgrade Commands upgrade start Start a new upgrade. SYNTAX: upgrade start protocol = <{tftp|ftp|http|https}> [server = <string>] [filename = <string>] where: protocol The protocol to be used for the download. REQUIRED Choose between: tftp http https The default is disabled. server The server name or IP address OPTIONAL...
Page 650: Upgrade Debug Traceconfig
Upgrade Commands upgrade debug traceconfig Enable/disable upgrade daemon tracing. SYNTAX: upgrade debug traceconfig state = <{disabled|enabled}> where: state Set the upgared daemon state to enabled or disabled. REQUIRED E-DOC-CTC-20060414-0002 v1.0...
Page 651: Upgrade Debug Sesslist
Upgrade Commands upgrade debug sesslist Display the list of sessions. SYNTAX: upgrade debug sesslist EXAMPLE: =>:upgrade debug sesslist Session 0: --------------------------------------------------------------- SessionId : 0x80c25850 State : IDLE Protocol : TFTP ServerName: FileName DestFile ServerIP : 0.0.0.0 Error Session 1: --------------------------------------------------------------- SessionId : 0x80c25c20 State : IDLE...
Page 652: Upgrade Profile Add
Upgrade Commands upgrade profile add Add a new file profile description. SYNTAX: upgrade profile add extension = <{sts|ini}> [maxsize(KBytes) = <number>] action = <{none|config_load|script_load|reboot}> where: extension The extension of the new file profile. REQUIRED Choose between: maxsize The maximum filesize (in KBytes) allowed for files with the OPTIONAL extension of this profile.
Page 653: Upgrade Profile Modify
Upgrade Commands upgrade profile modify Modify a file profile description. SYNTAX: upgrade profile modify extension = <{sts|ini}> [maxsize(KBytes) = <number>] action = <{none|config_load|script_load|reboot}> where: extension The extension of the new file profile. REQUIRED Choose between: maxsize The maximum filesize (in KBytes) allowed for files with the OPTIONAL extension of this profile.
Page 654: Upgrade Profile Delete
Upgrade Commands upgrade profile delete Delete a file profile description. SYNTAX: upgrade profile delete extension = <{sts|ini}> where: extension The extension of the profile to be deleted. REQUIRED Choose between: RELATED COMMANDS: upgrade profile add Add a new file profile description. upgrade profile list Display a list of the file profile descriptions.
Page 655: Upgrade Profile List
Upgrade Commands upgrade profile list Display a list of the file profile descriptions. SYNTAX: upgrade profile list RELATED COMMANDS: upgrade profile delete Delete a file profile description. upgrade profile modify Modify a file profile description. E-DOC-CTC-20060414-0002 v1.0...
Page 656 Upgrade Commands E-DOC-CTC-20060414-0002 v1.0...
Page 657: Upnp Commands
UPnP Commands UPnP Commands Introduction This chapter describes the commands of the upnp command group. Contents This chapter covers the following commands: upnp config Configure the UPnP™ parameter(s). upnp flush Flush the UPnP™ configuration. upnp list List all registered devices. E-DOC-CTC-20060414-0002 v1.0...
Page 658: Upnp Config
A number between 60 and 999999. OPTIONAL This parameter allows to configure how often the SpeedTouch™ sends a notification message to advertise its presence as an Internet Gateway Device (IGD) on the network. The default is 1800. Note...
Page 659: Upnp Flush
UPnP Commands upnp flush Flush the UPnP™ configuration. The UPnP configuration will be reset to the default configuration. SYNTAX: upnp flush E-DOC-CTC-20060414-0002 v1.0...
Page 660: Upnp List
UPnP Commands upnp list List all registered devices. Use this command to check whether a PPP connection is properly configured and thus advertised as a PPP service. SYNTAX: upnp list [verbose = <number{0-2}>] where: verbose Verbose level. OPTIONAL The default is 1. EXAMPLE: =>upnp list ---------------- device: IGD.xml ------------...
Page 661: User Commands
User Commands User Commands Introduction This chapter describes the commands of the user command group. Contents This chapter covers the following commands: user add Add a user. user config Modify a user. user delete Delete a user. user flush Flush the users. user list Display the users.
Page 662: User Add
User Commands user add Add a user. You can only add a user whose privileges are the same or lower than your own privileges. SYNTAX: user add name = <quoted string> password = <password> role = <string> [hash2 = <string>] [descr = <quoted string>] [defuser = <{disabled | enabled}>] [defremadmin = <{disabled | enabled}>]...
Page 663 User Commands In the example below, the user Administrator creates a new user JohnDoe. This user has lower access rights than the user “Poweruser”. {Administrator}=>user list User Flags Role ---- ----- ---- Administrator Administrator tech TechnicalSupport {Administrator}[user]=>add name = JohnDoe password = **** Please retype password for verification.
Page 664: User Config
User Commands user config Modify a user. You can only modify a user whose privileges are the same or lower than your own privileges. SYNTAX: user config name = <string> [password = <password>] [role = <string>] [descr = <quoted string>] [defuser = <{disabled | enabled}>] [defremadmin = <{disabled | enabled}>] [deflocadmin = <{disabled | enabled}>]...
Page 665 User Commands EXAMPLE: {Superuser}=>user list User Role ==== ==== Superuser root aPoweruser Poweruser {Superuser}=>user config name=aPoweruser role=LAN_admin {Superuser}=>user list User Role ==== ==== Superuser root aPoweruser LAN_admin {Superuser}=> E-DOC-CTC-20060414-0002 v1.0...
Page 666: User Delete
User Commands user delete Delete a user. You can only delete a user whose privileges are the same or lower than your own privileges. SYNTAX: user delete name = <string> where: name The name of the user to be deleted. REQUIRED EXAMPLE: {Administrator}=>user list...
Page 667: User Flush
Flush the users. After execution of this command, the access to the SpeedTouch™ will no longer be protected by a password. The first user that logs on, after initiating a new Telnet session, will have the same administrative rights as a user with the role root.
Page 668: User List
User Commands user list Display the users. SYNTAX: user list [name = <string>] [channel = <{ftp | telnet | http | mdap | serial}>] [origin = <{lan | wan | local}>] [secure = <{disabled | enabled}>] where: name The user name. OPTIONAL Note If not specified, all the users will be listed.
Page 669 User Commands EXAMPLE: {Administrator}=>user list User Flags Role ---- ----- ---- Administrator Administrator tech TechnicalSupport {Administrator}=>user list name=tech channel=http origin=wan service(s): r_lan, r_wan, r_fs_view, r_fs_retrieve, r_rtg, r_fwdg, r_nat, r_frwl, r_ipsec_norm, r_ipsec_adv, r_certificates, r_remote_mgnt, r_local, r_qos, w_lan, w_wan, w_fs_passive, w_rtg, w_fwdg, w_nat, w_frwl_norm, w_frwl_adv, w_frwe_mgnt, w_ipsec, w_certificates, w_remote_mgnt, w_local, w_qos, snd_lan, snd_wan, snd_local, and_lan, and_wan, and_frwl, and_local, user_admin, mlp_admin, secure_ipsec_term, secure_br, cli, cgi, ftp, mdap,...
Page 670: User Rights
User Commands user rights Display the session rights. The user rights of the currently logged-in user are shown. SYNTAX: user rights EXAMPLE: {Administrator}=>user rights Current session info: user: name='Administrator', role='Administrator' access: lan (origin_lan), telnet (channel_telnet), unsecure (unsecure_connection) service(s): r_lan, r_wan, r_fs_view, r_fs_retrieve, r_rtg, r_fwdg, r_nat, r_frwl, r_ipsec_norm, r_ipsec_adv, r_certificates, r_remote_mgnt, r_local, r_qos, w_lan, w_wan, w_fs_passive, w_rtg, w_fwdg, w_nat, w_frwl_norm, w_frwl_adv, w_frwe_mgnt, w_ipsec, w_certificates, w_remote_mgnt, w_local, w_qos,...
Page 671: Abbreviations
Abbreviations Abbreviations The table below lists all the abbreviations used in the CLI Reference Guide. Abbreviation Description AAL5 ATM Adaption Layer 5 Access Control List ADSL Asymmetric Digital Subscriber Line Advanced Encryption System Assured Forwarding Access Point Address Resolution Protocol Asynchronous Transfer Mode BSSID Base Service Set IDentifier...
Page 672 Abbreviations Abbreviation Description HDLC High-level Data Link Control HTTP HyperText Transfer Protocol ICMP Internet Control Message Protocol Intrusion Detection System Internet Gateway Device IGMP Internet Group Management Protocol Internet Key Exchange Internet Protocol IP oA IP over ATM IPCP Internet Protocol Control Protocol IPSec IP Security ISDN...
Page 673 Abbreviations Abbreviation Description Point-to-Point Protocol PPPoA PPP over ATM PPPoE PPP over Ethernet PPTP Point-to-Point Tunneling Protocol Power Spectral Density Pre-Shared Key Permanent Virtual Channel Quality of Service Routing Information Protocol Real Time Clock Round Trip Time Security Associations SFTP Secure File Transfer Protocol SHDSL Single Pair High-speed Digital Subscriber Line...
Page 674 Abbreviations Abbreviation Description VLAN Virtual Local Area Network VLSM Variable Length Subnet Masking Virtual Path Virtual Path Identifier Virtual Private Networking Wide Area Network Wireless Distribution System Wired Equivalent Privacy Weighted Fair Queueing WINS Windows Internet Naming Service WLAN Wireless LAN Wi-Fi Protected Access Weighted Round Robin E-DOC-CTC-20060414-0002 v1.0...
Page 675: System Logging Messages
System Logging Messages System Logging Messages Introduction This chapter lists the different System Logging messages. Contents This chapter lists the different System Logging messages of the following modules: Auto-PVC Module Configuration Module DHCP Client Module DHCP Relay Module DHCP Server Module Dyndns Module Firewall Module LOGIN Module...
Page 676: Auto-Pvc Module
System Logging Messages Auto-PVC Module Facility Severity Contents LOCAL5 WARNING AUTOPVC script <script_name> failed LOCAL5 WARNING AUTOPVC script <script_name> failed LOCAL5 WARNING AUTOPVC script <script_name> (name1, qosb_name) failed LOCAL5 WARNING AUTOPVC script <script_name> (name1, qosb_name, name2) failed LOCAL5 WARNING AUTOPVC script 'autopvc_change_qos (itable[i].intf, name1, qosb_name) failed LOCAL5 WARNING AUTOPVC script <script_name>...
Page 677: Dhcp Relay Module
System Logging Messages DHCP Relay Module Facility Severity Contents LOCAL2 WARNING DHCR relay: Dropping boot rqs on interface <intf_id> due to invalid giaddr for server (<ip-address>) LOCAL2 WARNING DHCR relay: Dropping boot reply with invalid relay agent option from <intf_id> LOCAL2 WARNING DHCR relay: Dropping boot request containing the relay agent option from...
Page 678: Dyndns Module
System Logging Messages Dyndns Module Facility Severity Contents DYNDNS WARNING <DYNDNS_ STR_ID> Connection failed to <dyndns_service> for client <dyndns_client> DYNDNS WARNING <DYNDNS_ STR_ID> Failed to resolve host name <dyndns_service> for client <dyndns_client> DYNDNS WARNING <DYNDNS_ STR_ID> Server Timeout(<dyndns_service>) for client <dyndns_client>...
Page 679: Login Module
System Logging Messages LOGIN Module Facility Severity Contents AUTH NOTICE LOGOUT User <user_id> logged out on <connection_type> (<ip-address>) AUTH NOTICE LOGOUT User <user_id> logged out on <connection_type> AUTH NOTICE LOGOUT <session_name> session of user <user_id> killed (<ip-address>) AUTH NOTICE LOGOUT <session_name> session of user <user_id> killed AUTH NOTICE LOGIN User <user_id>...
Page 680: Ppp Module
System Logging Messages PPP Module Facility Severity Contents LOCAL0 WARNING PPP Link up (<intf name>) LOCAL0 WARNING PPP Link down (<intf name>) AUTH ERROR PPP PAP authentication failed (<intf name>) [protocol reject] AUTH INFO PPP PAP on intf <intf_id> no response to authenticate-request AUTH NOTICE PPP PAP remote user <remote_user_name>...
Page 681: Rip Module
System Logging Messages RIP Module Facility Severity Contents LOCAL1 INFO RIP Packet received from unknown interface LOCAL1 INFO RIP Packet size is smaller than minimum size LOCAL1 INFO RIP Packet size is greater than maximum size LOCAL1 INFO RIP Wrong RIP packet alignment LOCAL1 INFO RIP RIP version 0 with command <command-name>...
Page 682: Routing Module
System Logging Messages Routing Module Facility Severity Contents LOCAL1 INFO GRP Default destination is routed via gateway <ip_address> LOCAL1 INFO GRP Default destination is not routed anymore via gateway <ip_address> SECURITY INFO LABEL Rule Id:<rule_id> Protocol: ICMP Src_ip: <ip_address> Dst_ip: <ip_address> ICMP message type: <message_type_name || message_type_id >...
Page 683: Software Module
System Logging Messages Software Module Facility Severity Contents KERN INFO SOFTWARE File <Filename> <receive || transmit> initiated KERN INFO SOFTWARE File <Filename> <receive || transmit><““ || not> successful terminated" UPnP Module Facility Severity Contents WARNING SECURITY UPnP<ActionName> refused for ip=<ip_address> NOTICE SECURITY UPnP <ActionName>...
Page 684 System Logging Messages E-DOC-CTC-20060414-0002 v1.0...
Page 685: Supported Key Names
Supported Key Names Supported Key Names Contents This chapter lists all the key names supported by the SpeedTouch™, that can be used for completing CLI command parameters: Supported IP Protocols Supported TCP/UDP Port Names Supported ICMP Type Names Supported Facilities...
Page 686: Supported Ip Protocols
Supported Key Names Supported IP Protocols For more information on the listed IP protocols, see RFC1340 or www.iana.org. Protocol name Number Description Authentication Header (AH) Exterior Gateway Protocol (EGP) Encapsulating Security Payload (ESP) Gateway Gateway Protocol (GGP) General Routing Encapsulation (GRE) Host Monitoring Protocol (HMP) icmp Internet Control Message Protocol (ICMP)
Page 687: Supported Tcp/Udp Port Names
Supported Key Names Supported TCP/UDP Port Names For more information on the listed TCP/UDP port assignments, see RFC1340 or www.iana.org. Port name Number Description echo Echo discard Discard systat Active Users daytime Daytime qotd Quote of the Day chargen Character Generator ftp-data File Transfer (Default data) File Transfer (Control)
Page 688 Supported Key Names Port name Number Description sntp Simple Network Time Protocol (SNTP) ingres-net INGRES-NET Service netbios-ns NETBIOS Naming System netbios-dgm NETBIOS Datagram Service netbios-ssn NETBIOS Session Service imap2 Internet Message Access Protocol (IMAP) v2 sql-net SQL-NET pcmail-srv PCMail Server snmp Simple Network Management Protocol (SNMP) snmptrap...
Page 689 Supported Key Names Port name Number Description utime UNIX Time Local routing process (on site); uses variant of Xerox NS Routing Information Protocol (RIP) timed Timeserver netwall For emergency broadcasts new-rwho uucpd remote who is uucp uucpd uucp-rlogin uucpd remote login rtsp Real Time Streaming Protocol (RTSP) whoami...
Page 690: Supported Icmp Type Names
Supported Key Names Supported ICMP Type Names For more information on the listed ICMP type names, see RFC1340 or www.iana.org. ICMP Type name Number Description echo-reply Echo Reply destination-unreachable Destination Unreachable source-quench Source Quench redirect Redirect echo-request Echo router-advertisement Router Advertisement router-solicitation Router Solicitation time-exceeded...
Page 691: Supported Facilities
UUCP subsystem cron Clock daemon security Security messages FTP daemon NTP subsystem audit Log audit logalert Log alert clock Clock daemon local0 Local use messages local1 local2 local3 local4 local5 local6 local7 All facilities (SpeedTouch™ specific facility parameter value. E-DOC-CTC-20060414-0002 v1.0...
Page 692: Supported Severities
Supported Key Names Supported Severities For more information on the listed severities, see RFC3164. Severity Name Hierarchy Syslog severity Code (listed according descending importance) emerg Emergency conditions, system unusable alert Alert conditions, immediate action is required crit Critical conditions Error conditions warning Warning conditions notice...
Page 693: Differentiated Services Code Point (Dscp)
Supported Key Names Differentiated Services Code Point (DSCP) For more information on DSCP, see RFC3260. PHB Name Binary value Expedited Forwarding 101110 af41 Assured Forwarding 41 100110 af42 Assured Forwarding 42 100100 af43 Assured Forwarding 43 100010 af31 Assured Forwarding 31 011110 af32 Assured Forwarding 32...
Page 694 Supported Key Names E-DOC-CTC-20060414-0002 v1.0...
Page 695 Index Index appconfig connection appconfig 76 aal5stats appinfo atm debug aal5stats 35 connection appinfo 78 actlist applist eth bridge dynvlan actlist 244 connection applist 79 arpadd atm bundle add 21 ip arpadd 387 atm oam vclb add 46 atm phonebook add 49 arpdelete atm qosbook add 54 ip arpdelete 388...
Page 696 Index list 39 dhcp client debug clear 113 modify 40 dhcp server debug clear 145 ping 42 dns server debug clear 182 vclb dns server debug spoof clear 184 add 46 eth bridge clear 242 del 47 firewall debug clear 312 list 48 firewall rule debug clear 327 phonebook...
Page 697 Index save 73 config delete 68 service host config 563 dhcp client rqoptions delete 117 snmp config 584 dhcp client txoptions delete 121 sntp config 601 dhcp relay delete 128 system config 610 dhcp rule delete 139 system ra config 620 dhcp server lease delete 151 upgrade dhcp server pool delete 164...
Page 698 Index txoptions disable add 120 service host disable 566 delete 121 list 122 relay client add 124 config 174 config 127 dnsadd 175 debug dnsdelete 176 stats 125 dnslist 177 traceconfig 126 flush 178 delete 128 nslookup 179 flush 129 server ifconfig 130 config 180...
Page 699 Index delete 209 mcddelete 262 flush 210 mcdlist 263 list 211 rule modify 212 add 264 delete 265 dump flush 266 config dump 69 list 267 vlan dyndns ifadd 268 add 214 ifconfig 269 delete 215 ifdelete 270 flush 216 iflist 271 host device...
Page 700 Index eth switch group flush 274 eth vlan flush 285 expr flush 293 firewall firewall chain flush 310 chain firewall flush 306 add 308 firewall level flush 317 delete 309 firewall rule flush 323 flush 310 grp flush 333 list 311 grp rip flush 337 config 304 hostmgr flush 347...
Page 701 Index gstats eth bridge ifattach 252 eth ifattach 236 atm debug gstats 36 ip auto ifattach 414 ip ifattach 394 ppp ifattach 526 snmp ifattach 594 ifconfig atm bundle ifconfig 29 hostmgr atm ifconfig 16 add 342 dhcp client ifconfig 106 clear 344 dhcp relay ifconfig 130 config 345...
Page 702 Index ip auto iflist 419 arplist 389 ip iflist 399 auto nat iflist 511 flush 412 ppp iflist 535 ifadd 413 ppp relay iflist 545 ifattach 414 snmp iflist 597 ifconfig 415 ifdelete 417 ifrenew ifdetach 418 dhcp client ifrenew 111 iflist 419 config 390 ifscan...
Page 703 Index list 437 dhcp client txoptions list 122 stats 438 dhcp relay list 133 dhcp rule list 141 dhcp server lease list 153 dhcp server pool list 166 dns server debug spoof list 187 dns server host list 192 dns server route list 196 Key names dsd syslog list 206 DSCP 673...
Page 704 580 atm oam cc modify 44 maplist atm oam modify 40 dhcp relay modify 134 nat maplist 516 dsd urlfilter rule modify 212 mbslist dyndns modify 218 igmp proxy mbslist 377 dyndns service modify 225 expr modify 300...
Page 705 Index tmpldelete 520 list 550 tmplinst 522 profadd 551 tmpllist 521 profdelete 552 proflist 553 nslookup profadd dns client nslookup 179 pptp profadd 551 profdelete pptp profdelete 552 proflist pptp proflist 553 optadd proxy dhcp server pool optadd 167 dsd debug proxy 201 optdelete dhcp server pool optdelete 168 optionlist...
Page 706 Index rtlist sesslist grp rtlist 334 ppp relay sesslist 546 ip mcast rtlist 407 upgrade debug sesslist 631 ip rtlist 411 ruleadd env set 231 dhcp relay ruleadd 135 firewall level set 320 dhcp server pool ruleadd 171 settime ruledelete system rtc settime 622 dhcp relay ruledelete 136 show...
Page 707 Index mbus debug stats 474 timerconfig memm stats 485 connection timerconfig 93 mlp debug stats 491 tmpladd service host stats 569 system debug stats 619 dhcp server option tmpladd 158 nat tmpladd 517 synchronize tmpldelete system rtc synchronize 621 dhcp server option tmpldelete 159 Syslog messages nat tmpldelete 520 Auto-PVC 656...
Page 708 Index add 632 delete 634 modify 633 software upgrade 606 start 629 upnp config 638 flush 639 list 640 user add 642 config 644 delete 646 flush 647 list 648 rights 650 version software version 607 walk snmp walk 587 E-DOC-CTC-20060414-0002 v1.0...
Page 710 Need more help? Additional help is available online at www.speedtouch.com...

This manual is also suitable for:

536546Speedtouch 516Speedtouch 536 Speedtouch 546

THOMSON 516 Reference Manual

Table of Contents

Table of Contents

Table of Contents

Quick Links

Chapters

Related Manuals for THOMSON 516

Summary of Contents for THOMSON 516