1. Manuals
  2. Brands
  3. Serpent Manuals
  4. Motorized Toy Car
  5. Serpent
  6. Instruction manual & reference manual

Serpent Instruction Manual & Reference Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
INSTRUCTION MANUAL
& REFERENCE GUIDE

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Serpent and is the answer not in the manual?

Questions and answers

Related Manuals for Serpent Serpent

Summary of Contents for Serpent Serpent

  • Page 1 INSTRUCTION MANUAL & REFERENCE GUIDE...

  • Page 2: Customer Service

    Replace when necessary. Do not use water, methanol, The exploded views and parts lists for the Serpent thinner or other solvents to clean the car. F110 are presented in the Reference Guide section - Empty the fuel tank (depending on model) if needed in the back of this manual.

  • Page 3: Using The Manual

    USING THE MANUAL Each step contains a variety of numbers, lines, and symbols. The numbers represent the order in which the parts should be assembled. The lines and symbols are described below. Step number; the order in which you should assemble the indicated parts Length after assembly Assembly path of one item into another...
  • Page 4 CA Glue To prevent the risk of the carbon fibre splitting in the event of a crash you should apply CA Glue around the chassis’ edge and the power pod plate external and internal edge as shown in red below. Nylock Nut M3 Low Alu 4mm Ride Height spacer (rubber tyres).
  • Page 5 Nylock nut M3 NOT INCLUDeD NOTE: It is needed to remove the 3x6x0.5 servo holes of the bottom part of the servo before going onto the step 4.4. Use the following servo saver insert with this brand of servos: 3x6x0.5 23 - Sanwa / KO / JR 24 - Hitec 25 - Futaba (default)
  • Page 6 Assemble the pivot-ball in the inner hole of the steeringblock as default setup. Steeringblock assembly detail view M3x3 M3x6 10.5 mm 13 mm 15 mm Trackrod M3x23 Trackrod M3x26 Detail view Approx. 30 mm M3x8 M3x6 Page...
  • Page 7 Nylock nut M3 M2.2x6 M3x10 Do not fully tighten these screws yet; fully tighten in step A12 M3x10 Nylock nut M3 3x6x6 M3x16 M3x16 M3x6 M3x6 3x6x0.5 M3x6 M3x5 M3x6 M3x6 M3x6 M3x6 Page M3x6...
  • Page 8 M3x5 M2x6 Adjust movement and play with these screws M2x6 3x5x2 3x5x2 M3x6 Tighten these screws after assembling M3x6 links (see step 8) Page...
  • Page 9 Configuration for 2S Standard Lipo M3x6 M2.5X5 M3x8 M3x6 M3x6 M2.5X5 M3x8 Note: see also pages 25-27 M3x6 M3x6 Configuration for 2S Shorty Lipo M3x6 M2.5X5 M3x6 M3x6 M2.5X5 M2.5X5 Note: see also pages 25-27 M2.5X5 M3x6 Page...
  • Page 10 M3x6 M3x10 M3x6 Detail view side spring 15.1 Fill the tube with heavy silicon oil (15000 cst) M3x10 15.2 Page...
  • Page 11 Note Spring washer orientation. 1/4x3/8 HOW TO ADJUST THE BALL-DIFF: In order to tighten or loosen the ball-diff, you should follow the next two steps: 1/4x3/8 Push a pin or a Allen tool through the Diff Hub slot into the hole of the adjusting nut Turn clockwise Spur gear is NOT...
  • Page 12 M3X6 M3X5 M3X6 Note position of the shock M2.5X8 ball joint (basic setup) M3X6 NOT INCLUDeD Electronics position with standard 2S Lipo Tip: Use double sided tape to mount the ESC and RX to the sideplates. INCLUDeD INCLUDeD Note: When using a 2S Standard Lipo Receiver-RX installed...
  • Page 13 Electronics position with Shorty 2S Lipo Tip: Use double sided tape to mount the ESC and RX to the chassisplate. Note: When using a Shorty 2S Lipo install ESC and RX as shown. (Page 25 shows Standard 2S Lipo INCLUDeD set-up).
  • Page 14 RCM SHOCK ASSEMBLY 20.1 20.2 20.3 2.5x6x0.5 Check the default set-up Nut M2.5 sheet for the correct piston to use Use some Locktite to Use some silicone oil Use some silicone oil fix the nut during assembly during assembly 20.4 20.5 20.6 Assemble the...
  • Page 15 M2X4 M2X4 M2X4 M3X6 M2X4 M3X6 M4X14 M3X8 M3X3 Pinion is NOT INCLUDeD in the kit. Assemble the proper pinion for your set-up Body, wheels and tyres are NOT included M3x4 Nylock Nut M4 5x8x0.3 5x10x4 5x8x0.1 Page Nylock nut M4...

  • Page 16: Section B: Reference Guide

    SECTION B: REFERENCE GUIDE...

  • Page 17: Front Assembly

    FRONT ASSEMBLY 411253 110124 110415 411288 411295 401057 411253 110108 110108 411063 411295 401582 411048 110108 110116 411299 110402 110415 411231 110415 411207 110108 411187 411253 411060 110137 411042 411206 902138 411143 411296 411300 411297 411207 411206 See parts list 411163 110402 411305...

  • Page 18: Ball Diff Assembly

    BALL DIFF ASSEMBLY 411309 411186 See parts list 411075 411069 411075 411186 411290 411251 411075 411306 411166 SHOCK ABSORBER ASSEMBLY 160111 160107 6442 160110 160105 160106 110437 909405 160104 110438 160108 160111 See parts list 160111 160111 160102 FINAL ASSEMBLY 110182 411007 411294...

  • Page 19: Parts List

    411303 Pod bulkhead left F110 411304 Pod bulkhead right F110 Decals 411307 Rear pod support plate carbon F110 1886 Decal Serpent black/white 1/10 (2) 411312 Rear wing F110 white 1888 Decal Serpent chrome 1/10 (2) 411309 Rear axle F110 411311...
  • Page 20 120116 Motor-pinion alu hard 64P / 29T 110161 Screw allen cilinderhead M2x6 (10) 120117 Motor-pinion alu hard 64P / 30T 110162 Setscrew allen M3x2.5 (10) 120118 Motor-pinion alu hard 64P / 31T 110163 Setscrew allen M3x2 (10) 120119 Motor-pinion alu hard 64P / 32T 110164 Screw allen roundhead M3x4 (10) 120120...
  • Page 21 Hoody sweater Serpent black-zip (L) 190204 Hoody sweater Serpent black-zip (XL) 190205 Hoody sweater Serpent black-zip (2XL) 190206 Hoody sweater Serpent black-zip (3XL) 190207 Hoody sweater Serpent black-zip (4XL) ) Pit equipment 190500 Pit-caddy 190501 Tool-bag 190502 Carry-bag medium. 3 drawers...
  • Page 22 - info@serpent.com...

This manual is also suitable for:

F110

Table of Contents