Page 2
Serpent drivers can enjoy. The Serpent S811 Cobra Truggy offers state of the art specifications and leads the way in 1/8 scale gas offroad chassis design, using all the knowledge our designers have gathered from racing offroad cars for over 15 years, into this design too.
Page 3
Step number; the order in which you should assemble the indicated parts Length after assembly / Gap between two items Assembly path of one item into another Group of items (within lines) should be assembled first Direction the item should be moved Glue one item to another Press/Insert one item into another Connect one item to another...
Page 4
CENTER 8x14x4 DIFF flanged 8x11x0.2 1 pc add 2mm oil before assembling the gear 8x14x4 flanged use silicone oil to hold seal in position 8x11x0.2 3 pc M3x12 silicone oil fill just over gear check default SET-UP sheet for CST value of the silicone oil...
Page 5
FR/RR 8x14x4 DIFF flanged 8x11x0.2 1 pc add 2mm oil before assembling the gear 8x14x4 flanged use silicone oil to hold seal in position M3x12 silicone oil fill just over gear check default SET-UP sheet for CST value of the silicone oil...
Page 6
Thick Thin Thin Thick M4x12 M3x10 small brakedisc at the back M3x3 big brakedisc in front 14x15.5x0.65 M3x8 use threadlock for these screws in the brakelever check for free movement...
Page 7
M5x4 14x15.6x0.2 use shims to adjust gear mesh 14x15.6x0.2 use shims to adjust gear mesh M3x14 M3x14...
Page 8
M3x40 proper insert orientation in the rear proper insert orientation in the front bracket, left and right equal type bracket, left and right equal type M3x16 M3x16 M3x16 M3x18 M3x16 M3x25 M3x18 Nylock M3...
Page 9
M3x12 flanged M3x12 flanged 56.5mm please notice the correct hole for the pin move clips over pin after assembling Nylock M3 M3x22...
Page 10
M3x3 M3x3 M3x3 M3x3 use threadlock on these screws 35mm M4x12 Nylock M3 Nylock M3 M3x12...
Page 18
NOT INCLUDED 5x10x4 M3x10 use threadlock INCLUDED on these screws M3x10 use threadlock on these screws M4x12...
Page 19
M3x8 M3x8 M3x8 M3x8 Inserts: 23T Sanwa / KO / JR 24T Hitec 25T Futaba NOT INCLUDED use enough servo-spacers to get clearance at the bottom of the servo! notice the orientation of the lever in neutral M3x16 position! M3x16 threadlock M3x8 M3x12...
Page 20
M2x10 M3x20 M3x8 M3x3 125mm M3x3 NOT INCLUDED 120mm NOT INCLUDED 24mm M3x8 M4x10...
Page 21
NOTE: use threadlock Bag 10 are FRONT shocks. Bag 11 are REAR shocks M2.5x6 10/11 Apply silicone oil to assemble the o-rings Apply silicone oil to assemble the shockshaft Apply silicone oil to mount the nut FRONT shock 113.5mm REAR shock 124mm...
Page 23
M3x4 NOTE: SHOCKS SHOWN M3x4 WITHOUT SHOCK BOOTS M3x4 M3x12 FLANGED 20MM M3x12 M3x12 NOTE: POSITION OF TANK POSTS...
Page 24
M4x4 NOT INCLUDED M4x10 use threadlock NOT INCLUDED on these screws Cut out as required NOTE: Put sufficient air filter oil on the airfilter before use (DO NOT use silicone oil!) M3x6...
Need help?
Do you have a question about the S811 Cobra Truggy and is the answer not in the manual?
Questions and answers