1
1-A Location of controls
Integrated Telephone System
Operating Instructions
KX-TS500HG
Model No.
Pulse-or-tone dialing capability
Accessories (included)
KX-TS500HGW
∑ Handset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . one
∑ Handset Cord . . . . . . . . . . . . . . . . . . . . . . . . . one
PLEASE READ BEFORE USE AND SAVE.
∑ Telephone Line Cord . . . . . . . . . . . . . . . . . . . one
3
For your future reference
3-A Recall Button
Serial No.
(found on the bottom of the unit)
Pressing (R) allows you to use special features
Date of purchase
of your host PBX such as transferring an
extension call or accessing special telephone
Name and address of dealer
services (optional) such as call waiting.
1999/5/EC
This equipment is designed for use on
Hungary only.
In the event of problems, you should contact
your equipment supplier in the first instance.
Manufactured by Panasonic
Communications (Malaysia) Sdn. Bhd.
Senai Malaysia
PQQX13969ZA
F1003-0 D
Getting Started
1-B Settings
1
VOLUME (^), (_)
DIALING MODE Selector
(1-B)
Buttons (2-A)
2
RINGER Selector
(1-B)
To Single-Line
Telephone Jack
(R) Button
($) Button (3-B)
(3-A)
Button (2-A)
Special Features
3-B Temporary Tone Dialing
Press ($) before entering access numbers
which require tone dialing.
≥The dialing mode changes to tone. You can enter
numbers to access answering services, electronic
banking services, etc. When you hang up, the
mode will return to pulse.
≥Access numbers entered after pressing ($) will not
be included when redialing.
3
Connect the telephone line cord (1).
Connect the handset cord (2), then confirm
the dial tone.
Telephone Line Cord
4
1
DIALING MODE
Selector
RINGER Selector
2
Handset
Handset Cord
4
4-A Wall Mounting
(For Rotary or Pulse Service Users)
The unit can be mounted on a wall.
1
Press the tabs in the direction of the arrows
(1), then remove the wall mounting adaptor
(2).
2
Tuck the telephone line cord inside the wall
mounting adaptor, and push it in the direction
of the arrow (1 and 2).
≥The word "UP WALL" should face upward.
2
2-A Making Calls
1
Set the DIALING MODE selector to TONE.
Lift the handset.
≥If you cannot dial, set to PULSE.
2
Dial a phone number.
DIALING MODE
≥If you misdial, hang up and start again from
TONE
PULSE
3
When finished talking, hang up.
Set the RINGER selector to HIGH, LOW or
To redial the last number dialed
Lift the handset. ➡ Press
OFF.
(Ex. "LOW" is selected.)
To adjust the receiver volume (6 levels)
RINGER
while talking
HIGH
OFF
To increase, press (^).
To decrease, press (_).
≥
After hanging up, the volume level will be saved.
≥
When set to OFF, the unit will not ring.
2-B Answering Calls
1
When the unit rings, lift the handset.
2
When finished talking, hang up.
Things You Should Know
3
Install screws using the wall template below.
Connect the telephone line cord. Mount the
unit, then slide down.
≥Fasten the cord to prevent it from being
2
Hooks
1
1
2
1
Operation
step 1.
(\\\)
.
" Things You Should Know
disconnected.
Screws
8.3 cm
To Single-Line
Telephone Jack