Table of Contents
Advertisement
EN 14
5.
FM242 AA
NORMAL OPERATION
RC button,
e.g. P+ or P-
STANDBY
RC sequence "0-6-2-5-9-6-OSD "(for Europe & A/P)
or
RC sequence "0-6-2-5-9-6-INFO+" (for USA/LatAm)
or
Short SAM pins (works also from Standby)
Do not store
settings made
during alignments
Ignore all "Service
unfriendly" modes
RC button,
e.g. P+ or P-
"UNDO" ignore
all "Service
unfriendly
RC sequence
modes"
"00"
Service Alignment Mode
Display "SAM" top level
"Standby"
menu
Settings made
during alignments
are stored
STANDBY
Figure 5-2 SAM Flowchart
How to enter
Use one of the following methods:
•
Use a standard RC-transmitter and key in the code 062596
directly followed by the OSD (i+) button
Note: the OSD (i+) is not available on the original FM242
remote control, therefore use another Philips remote
control (e.g. MG, EMG or A10).
•
Short jumpers 3 and 4 of connector 0382 on the SCAVIO
panel.
The following screen is visible:
Service Alignment Menu
Type Nr. -
AG Code
SW Version OTC
SW Version PW
SW Version EPLD
Errors 1
Errors 2
Operational hours
Reset error buffer
Figure 5-3 SAM Menu 'General'
1. Type Nr. Gives the commercial type number of the
monitor, e.g. 42FD9945/01.
2. AG Code. Is not implemented.
3. SW Version OTC (AAAAAB-X.Y-xxxxx).
Note: You will find details of the latest software versions in
the chapter 'Software Survey' of the 'Product Survey -
Colour Television' publication, which is published four
times each year.
•
A = the chassis name (FM23 for 32" displays or FM242
for 42" SDI-displays).
•
B = the region (E= Europe, A= Asia Pacific, U= NAFTA,
L= LATAM; in our case G = Global).
•
(if valid) C = the configuration name (B= Basic, E=
Enhanced; for PW & EPLD-software this will be named
B).
•
X = the main software version number.
•
Y = the sub software version number.
•
x = last five digits of 12nc code.
Service Modes, Error Codes and Fault Finding
Mains ON
OFF
(Settings made
during alignments
are stored)
Mains OFF
RC-code "0-6-2-5-9-6-OSD"
or
RC-code "0-6-2-5-9-6-INFO+"
RC-code "0-6-2-5-9-6-MENU" -
Upper menu selection
(with cursor buttons)
SAM submenus
(whitepoints, align-
Lower menu selection
ments, etc.)
(with cursor buttons)
CL 16532099_101.pdf
General
42FD9945/01 **00 00
AAAAAB-X.Y_xxxxx
AAAABC-X.Y_xxxxx
AAAABC-X.Y_xxxxx
xx xx xx xx xx
xx xx xx xx xx
xx
Press OK to reset
Store
Press OK to store
CL 26532011_016.eps
4. SW Version PW (AAAABC-X.Y-xxxxx). See description
above.
5. SW Version EPLD (AAAABC-X.Y-xxxxx). See description
above.
6. Errors 1. Gives the last five errors of the error buffer. The
last detected error is displayed at the most left position.
The errors are displayed as 2 digit numbers and separated
by a space. When less than 10 errors occurred, the rest of
the line(s) is empty. In case of no errors the text 'No Errors'
is displayed behind menu item 'Errors 1'. See paragraph
5.5 for a description.
7. Errors 2. Gives the first five errors of the error buffer. The
last detected error is displayed at the most left position.
8. Operational hours. The Operations Hours indicate the
time that the display was active with half an hour resolution.
It represents the system hours (OTC), not the PDP hours.
9. Reset error buffer. Erase the contents of the error buffer.
Press 'OK' on your remote control to activate. The content
of the error buffer is cleared.
SDM
10. Store. This will store the performed alignments. Press 'OK'
on your remote control to activate.
Note: if you do not want to store the performed alignments,
leave the SAM mode via code 00 on your remote control.
Do not activate the 'store' item.
How to navigate
260901
Use one of the following methods:
•
Select the sub-menu's (upper line) with the CURSOR
LEFT/RIGHT keys on the remote control transmitter.
•
Select the menu items with the CURSOR UP/DOWN keys.
With the CURSOR LEFT/RIGHT keys it is possible to:
–
–
•
To toggle to the SDM mode, use the standard customer
RC-transmitter and key in the code 062596, directly
followed by the MENU key.
How to exit
Use one of the following methods:
•
Switch the set 'off' (with the Mains switch or by pulling the
Mains cord).
Note: new alignment settings are always stored, even
when item 'store' was not activated!
•
Switch the set to 'standby' by pressing the power button on
the remote control transmitter.
Note: new alignment settings are always stored, even
when item 'store' was not activated!
•
Use the standard RC-transmitter and key in the code 0 0.
Note: new alignment settings are not stored (except when
item 'store' was activated)!
5.2.3
Customer Service Mode (CSM)
200303
Purpose
When a customer is having problems with his TV-set, he can
call his dealer or helpdesk. The service technician can than ask
the customer to activate the CSM, in order to identify the status
of the set. Now, the service technician can judge the severe
ness of the complaint. In many cases, he can advise the
customer how to solve the problem, or he can decide if it is
necessary to visit the customer.
The CSM is a read only mode, therefore modifications in this
mode are not possible.
Activate the selected menu item.
Change the value of the selected menu item.
Advertisement
Table of Contents
