JVC XV-N322S Instructions

DVD PLAYER Warnings, Cautions and Others
XV-N320B
CAUTION
RISK OF ELECTRIC SHOCK
XV-N322S
DO NOT OPEN
INSTRUCTIONS CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK)
NO USER SERVICEABLE PARTS INSIDE.
® REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash
V I D E O
symbol, within an equilateral triangle is
GNT0059-002B[UC]
intended to alert the user to the presence
EN 1104MOC-MW-SC
of uninsulated "dangerous voltage" within
©2005 Victor Company of Japan, Limited
the products enclosure that may be of
Region code of DVD VIDEO
sufficient magnitude to constitute a risk of
This player can play back DVD VIDEO discs
electric shock to persons.
whose region code numbers include "1."
The exclamation point within an equilateral
Examples of playable DVD VIDEO discs:
triangle is intended to alert the user to the
presence of important operating and
1 2
1 2 3
ALL 1 1 5
maintenance (servicing) instructions in the
4 5 6
3 4
literature accompanying the appliance.
The player's region code is printed on the rear of
WARNING: TO REDUCE THE RISK OF FIRE OR
the player
ELECTRIC SHOCK, DO NOT EXPOSE THIS
Note of Color system format
APPLIANCE TO RAIN OR MOISTURE.
This player accommodates the NTSC system, and
For U.S.A.
also can play back discs recorded with PAL
This equipment has been tested and found to comply
system. (PAL video signals are converted to an
with the limits for a Class B digital device, pursuant to
NTSC signal and output.)
part 15 of the FCC Rules.
Supplied accessories
These limits are designed to provide reasonable
If anything is missing, consult your dealer
protection against harmful interference in a residential
immediately.
installation. This equipment generates, uses and can
• Audio/video cable (Yellow/White/Red) (x 1)
radiate radio frequency energy and, if not installed
• Remote control (x 1)
and used in accordance with the instructions, may
• R6(SUM-3)/AA(15F) battery (x 2) cause harmful interference to radio communications.
However, there is no guarantee that interference will
not occur in a particular installation. If this equipment
does cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver. Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV
technician for help.
For Canada/pour le Canada
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH
WIDE BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
ATTENTION: POUR EVITER LES CHOCS
ELECTRIQUES, INTRODUIRE LA LAME LA PLUS
LARGE DE LA FICHE DANS LA BORNE
CORRESPONDANTE DE LA PRISE ET POUSSER
JUSQUAU FOND.
1
Turning on the power Initial setup
When you turn on the player for the first time after
Inserting the AC power plug
purchase, the following message appears on the TV
After all other connections have been made, insert the
screen.
AC power plug to the wall outlet firmly.
EXECUTE DVD PLAYER SETUP? - BASIC PICTURE/AUDIO
SETTING
Installing the batteries in the remote control
YES - PRESS ENTER NO - PRESS CANCEL
Open the compartment cover, and place the two
Before enjoying this player, make the initial settings as
supplied R6(SUM-3)/AA(15F) batteries in the remote
follows:
control according to the polarity markings ("+" and "–")
inside the compartment. Then replace the cover. 1
Press ENTER.
DVD PLAYER SETUP
MENU LANGUAGE ENGLISH
AUDIO LANGUAGE ENGLISH
SUBTITLE OFF
ON SCREEN LANGUAGE ENGLISH
ENGLISH
FRENCH
SPANISH
2 Press 5/∞ to select the on-screen language for
the preference displays, etc., then press ENTER.
DVD PLAYER SETUP
MONITOR TYPE 4:3 L.B.
16:9
PICTURE SOURCE AUTO
4:3 LB
4:3 PS
SCREEN SAVER ON
BACKGROUND STANDARD
The batteries will last about six months with normal use.
If the functions of the remote control become erratic,
replace the batteries.
Press 5/∞ to select the monitor type, then press
3
Precautions of the safe use of batteries ENTER.
Observe the following precautions for the safe use of • For a normal (conventional) TV, select "4:3 LB" or
batteries. If they are used improperly their lives will be "4:3 PS." (See "MONITOR TYPE" in "Initial
shortened, they may burst or their contents may leak. settings.")
• Remove the batteries from the remote control if it is • For a wide-screen TV, select "16:9."
not going to be used for a long period of time.
DVD PLAYER SETUP
• Remove dead batteries and dispose of them
DIGITAL AUDIO OUTPUT DOLBY DIGITAL/PCM
properly.
PCM ONLY
ANALOG DOWNMIX DOLBY PROLOGIC
• Never leave dead batteries lying around, take them DOLBY DIGITAL/PCM
STREAM/PCM
D.RANGE CONTROL ON
apart, mix them with other refuse, or throw them into
OUTPUT LEVEL STANDARD
an incinerator.
• Never touch liquid that has leaked out of a battery.
• Do not mix new and old batteries, or batteries of
different types, when placing them. Press 5/∞ to select a desired digital output
4
signal type, then press ENTER.
Turning on and off the player Set this item correctly according to the logo on your
receiver or decoder.
Press STANDBY/ON.
(If you do not connect the player to such a device,
press ENTER to finish the setting.)
• Receiver/decoder bearing Dolby Digital logo and
no DTS, select "DOLBY DIGITAL/PCM."
• Receiver/decoder bearing both Dolby Digital and
DTS logos, select "STREAM/PCM."
• Receiver/decoder bearing neither Dolby Digital nor
DTS logo, or digital recorder, select "PCM ONLY."
To bring up the DVD PLAYER SETUP display later
Press SET UP for a few seconds until the DVD PLAYER
SETUP display appears.
5
For Canada/pour le Canada CLASS 1 LASER PRODUCT
REPRODUCTION OF LABELS
THIS DIGITAL APPARATUS DOES NOT EXCEED THE
WARNING LABEL INSIDE OF THE UNIT
CLASS B LIMITS FOR RADIO NOISE EMISSIONS
FORM DIGITAL APPARATUS AS SET OUT IN THE PRODUIT LASER DE CLASSE 1
INTERFERENCE-CAUSING EQUIPMENT STANDARD REPRODUCTION D'ETIQUETTES
ENTITLED "DIGITAL APPARATUS," ICES-003 OF ETIQUETTE D'AVERTISSEMENT A L'INTERIEUR DE
THE DEPARTMENT OF COMMUNICATIONS. L'APPAREIL
CET APPAREIL NUMERIQUE RESPECTE LES
LIMITES DE BRUITS RADIOELECTRIQUES
APPLICABLES AUX APPAREILS NUMERIQUES DE
with arrowhead
CLASSE B PRESCRITES DANS LA NORME SUR LE
MATERIEL BROUILLEUR: "APPAREILS
CAUTION:
NUMERIQUES", NMB-003 EDICTEE PAR LE
• Do not block the ventilation openings or holes. (If the
MINISTRE DES COMMUNICATIONS.
ventilation openings or holes are blocked by a
CAUTION
newspaper or cloth, etc., the heat may not be able to
To reduce the risk of electrical shocks, fire, etc.:
get out.)
1. Do not remove screws, covers or cabinet.
• Do not place any naked flame sources, such as
2. Do not expose this appliance to rain or moisture.
lighted candles, on the apparatus.
ATTENTION
• When discarding batteries, environmental problems
Afin d'éviter tout risque d'électrocution, d'incendie, etc.:
must be considered and local rules or laws governing
1. Ne pas enlever les vis ni les panneaux et ne pas
the disposal of these batteries must be followed
ouvrir le coffret de l'appareil.
strictly.
2. Ne pas exposer l'appareil à la pluie ni à l'humidité.
• Do not expose this apparatus to rain, moisture,
dripping or splashing and that no objects filled with
Caution –– STANDBY/ON button!
liquids, such as vases, shall be placed on the
Disconnect the mains plug to shut the power off
apparatus.
completely. The STANDBY/ON button in any
ATTENTION:
position does not disconnect the mains line. The power
• Ne bloquez pas les orifices ou les trous de ventilation.
can be remote controlled.
(Si les orifices ou les trous de ventilation sont bloqués
Attention –– Touche STANDBY/ON!
par un journal un tissu, etc., la chaleur peut ne pas
Déconnecter la fiche de secteur pour couper
être évacuée correctement de l'appareil.)
complètement le courant. La touche STANDBY/ON
• Ne placez aucune source de flamme nue, telle
ne coupe jamais complètement la ligne de secteur,
qu'une bougie, sur l'appareil.
quelle que soit sa position. Le courant peut être
• Lors de la mise au rebut des piles, veuillez prendre
télécommandé.
en considération les problèmes de l'environnement et
suivre strictement les règles et les lois locales sur la
mise au rebut des piles.
CAUTION
• N'exposez pas cet appareil à la pluie, à l'humidité, à
THIS PRODUCT USES A LASER SYSTEM.
un égouttement ou à des éclaboussures et ne placez
USE OF CONTROLS OR ADJUSTMENTS OR
pas des objets remplis de liquide, tels qu'un vase, sur
PERFORMANCE OF PROCEDURES OTHER THAN THOSE
l'appareil.
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF.
REFER SERVICING TO QUALIFIED PERSONNEL.
ATTENTION:
CE PRODUIT UTILISE UN SYSTEME LASER.
UN EMPLOI DES COMMANDES, RÉGLAGES OU
PROCÉDURES DE PERFORMANCE AUTRE QUE CELUI
SPÉCIFIÉ DANS CE DOCUMENT RISQUE D'ENTRAÎNER
UNE EXPOSITION DANGEREUSE AUX RAYONNEMENTS.
NE PAS OUVRIR NI RÉPARER DE VOUS-MÊME. FAIRE
APPEL À UN PERSONNEL QUALIFIÉ POUR L'ENTRETIEN.
2
Basic Operations
Insert a disc
Press 0 to open the disc tray.
1
2
Place a disc in the disc tray.
Turning on and off the player
• To insert an 8-cm disc, place it in the inner
recess.
Press 0 to close the disc tray.
3
Point toward the remote sensor directly as possible
(the operating range is approx. 5 m.)
About On-screen guide icons
: Playback.
: Pause.
Main display / : Slow-motion playback with the current
• Each indicator lights up when corresponding speed.
function/mode is activated, or corresponding
/ : Fast forward/backward playback with the
information is on the main display.
current speed.
: At the beginning of a scene containing multi-
angle views.
: At the beginning of a scene containing multi-
audio sounds.
: At the beginning of a scene containing multi-
subtitles.
You can change the setting so that the on-screen
guide icons do not appear on the TV screen. (See
"ON SCREEN GUIDE" in "Initial settings.")
6
Precautions
Notes on the power cord
• DVD VIDEO, Audio CD, Video CD, SVCD
• When you are away on travel or otherwise for an extended
period of time, remove the plug from the wall outlet. A
small amount of power (1.0 W) is always consumed while
the power cord is connected to the wall outlet.
• DVD-R/-RW written in the DVD VIDEO format
• When unplugging the player from the wall outlet,
• CD-R/RW written in the SVCD, Video CD or Audio CD forma t
always pull the plug, not the power cord.
• CD-R/RW written in MP3/JPEG in accordance with
• Do not handle the power cord with wet hands!
• Disconnect the power cord before cleaning the
Supported Digital audio formats:
player or moving the player.
Linear PCM, Dolby Digital, DTS (Digital Theater Systems)*
• Do not alter, twist or pull the power cord, or put
NOTES
anything heavy on it, which may cause fire, electric
• If a disc gets dirty, scratched or warped, or due to the
shock, or other accidents.
• If the cord is damaged, consult a dealer and have the
power cord replaced with a new one.
• The player can play back audio signals recorded in
Avoid moisture, water, dust, and high temperatures
• Do not place the player in moist or dusty places.
• With some discs, operations may not be possible.
• If water gets inside the player, turn off the power and
* To play back DTS-encoded DVD VIDEO or DTS-
remove the plug from the wall outlet, then consult
your dealer. Using the player in this state may cause
a fire or electrical shock.
• Do not expose the player to direct sunlight or place it
Unplayable discs
near a heating device.
If you try to play back discs listed below, noise may be
Notes on installation
generated and causes damage to speakers.
• Select a place which is level, dry and neither too hot
• DVD-RW written in the VR format
nor too cold between 5˚C and 35˚C.
• DVD-ROM, DVD-RAM, DVD AUDIO, CD-ROM,
• Leave sufficient distance between the player and the TV.
• Do not install the player in a place subject to vibrations.
• Unfinalized discs
• Do not put heavy objects on the player.
• Discs of irregular shape or discs with tape, seals or
To prevent malfunction of the player
• There are no user-serviceable parts inside. If anything goes
wrong, unplug the power cord and consult your dealer.
• Do not insert any metallic objects, such as wires, The Non-DVD side of a "DualDisc" does not comply with
hairpins, coins, etc. into the player. the "Compact Disc Digital Audio" standard.
• Do not block the vents. Blocking the vents may Therefore, the use of Non-DVD side of a DualDisc on
damage the player. this product may not be recommended.
To clean the cabinet
• Use a soft cloth. Follow the relevant instructions on
the use of chemically-coated cloths.
• Do not use benzene, thinner or other organic solvents and
disinfectants. These may cause deformation or discoloring.
3
Turning on and off the player
Open/close the disc tray
OPEN/
CLOSE
Basic playback
– SLOW +
Buttons To do
3*
Start/resume normal Playback
7
Stop ENTER
• When RESUME is ON or DISC
RESUME, this player memorizes
the position on the disc where
PREVIOUS SELECT
you interrupted playback.
– To resume playback, press 3.
CLEAR
– To stop playback completely,
press 7 again.
1
8*
Pause
4
• Each time you press 8 on the
remote control, the still picture 7
CANCEL
advances to the next frame.
¡/1 Fast forward/backward
TITLE/ SOUND
GROUP EFFECT
(While paused)
Slow-motion playback
ANGLE SUBTITLE
• Each time you press the button,
the playback speed changes.
SLIDE EFFECT
With the label side up
¢/4 Skip chapter/track
• If you press and hold the button
during playback, playback is
advanced/reversed at 5 times
normal speed.
VARI-PLAY (For DVD Video)
(variable
The disc is played back at about
7 For DVD
playback)
1.2 or 1.5 times (FAST)/0.8 or 0.6
times (SLOW) normal speed. 1 Press TOP MENU or MENU to show the disc menu.
The sound is not muted, and the 2 Press 5/∞/2/3 to select a desired item, then press
ENTER or 3 (SELECT).
subtitle does not go off (except for
DTS). • With some discs, you can also select items by entering the
number using the numeric buttons.
(For SVCD/VCD)
7 For SVCD/VCD
The disc is played back at about 2
times (FAST)/0.5 times (SLOW) While stopped, press TOP MENU or 3 (SELECT) to
1
normal speed.
show the menu.
2
(Only for DVD Video) Press the numeric buttons to select a desired item.
To select 5: press 5.
The playback position moves
To select 23: press 2, then 3.
back 10 seconds before the
To select 40: press 4, then 0.
current position (only within the
• To move to the next or previous page of the current menu,
same title).
press ¢ or 4.
* 38 on the player starts/pauses playback.
• To return to the previous menu, press RETURN.
To play back without PBC
While stopped, press the numeric buttons instead of 3
(SELECT) to start playback.
Changing the display brightness
To reactivate PBC
Press DIMMER to change the brightness of
• Press TOP MENU or MENU.
the display window.
• Press 7 to stop playback, then 3 (SELECT).
7
Playable discs Connections
Before making connections:
• Do not connect the AC power cord until all other connections have been made.
• Connect VIDEO OUT of the player directly to the video input of your TV. Connecting VIDEO OUT of the
V I D E O
player to a TV via a VCR/an integrated TV/Video system may cause a monitor problem.
Basic Connection
S-video cable*
the "ISO 9660" format
(not supplied)
disc characteristics or recording conditions, the
player may not be able to play back such discs.
MIX-MODE CD, CD-G, CD-EXTRA and CD TEXT.
encoded Audio CD discs correctly, connect the
player to an amplifier with a built-in DTS decoder.
Otherwise, playback sound will be distorted. Yellow
Audio/video
cable*
(supplied)
PHOTO CD, SACD
Connecting to a TV with component jacks
paste on either the label side or playback side.
Playing back these discs may damage the player.
P B
OAXIAL Y RIGHT
REAM
LEFT
S-VIDEO VIDEO P R
AUDIO OUT
OUT VIDEO OUT
To component video input
To switch the scanning mode between Progressive and
Interlace, press and hold VFP-I/P on the remote control
for a few seconds.
NOTES
• Connect "Y" to "Y,""P " to "P (C
B B
correctly.
• When using the component (Y, P
connect the S-VIDEO jack with the player.
About the scanning mode indicator
[PICTURE SOURCE] of Source type of DVD VIDEO
the PICTURE menu Film source
AUTO [DDP]
FILM [DDP]
VIDEO(NORMAL)/
[P]
(ACTIVE)
NOTE
Some progressive TV and High-Definition TV sets are
not fully compatible with the player. To check the
compatibility of your TV, contact your local JVC
customer service center.
Advanced Operations
Changing the display window Changing the language, sound
contents
and scene angle
Each time you press DISPLAY,
1 Press the button.
STANDBY/ON
the display window contents
2
Press the button repeatedly or
changes. 5/∞ to select the desired item.
DISPLAY ON SCREEN
3
Press ENTER to finish the
Locating the beginning of a scene setting.
or song
Buttons To do
You can select a title/chapter/
AUDIO For DVD Video:
track directly and start playback.
select audio languages.
For DVD Video:
For SVCD/VCD:
(While stopped) select title.
NEXT select the audio
(While playing back) select
channel.
chapter.
SUBTITLE select the subtitle.
For SVCD/VCD/CD:
Select track.
2 3 ANGLE select the view-angle.
To select 5: press 5.
5 6
To select 23: press 2, then 3.
To select 40: press 4, then 0.
8 9
Changing the Sound Field
RETURN • If you press TITLE/GROUP
0
Each time you press SOUND
before entering the number, you
EFFECT, the Sound Effect mode
can select the title instead of the
VFP DIMMER
I/P changes.
chapter.
• As the value becomes bigger, the
AUDIO ZOOM
Sound Effect works stronger.
Using the disc menu
You can operate a disc—SVCD/
VCD with Playback Control*
(PBC)—using the disc menu
shown on the TV screen. Zooming the picture
* A method of controlling disc play
Each time you press ZOOM, the
for SVCD/VCD by using the disc
magnification changes.
menu.
• You can use 5/∞/2/3 button to
move the zoomed position.
To return to the normal playback,
select the normal size by pressing
ZOOM repeatedly.
TV
NOTES
• If your TV has a monaural audio input
IN
instead of stereo, use an optional audio
S- VI
DE O
cable which converts stereo audio output
V ID
E O
to monaural.
• If your TV is a HDTV or HD-ready TV, you
LE FT
A U D can connect with component (Y, P B , P R )
IO
RI GH jacks. By connecting with component (Y,
T
P , P ) jacks, you can select the
B R
progressive scanning mode which provides
the best picture quality.
* The S-VIDEO jack and component (Y, P ,
B
PC M
/S TR CO AX
EA M IAL The player P ) jacks cannot be used at the same time.
R
P
Y R
When using the S-VIDEO jack, do not
DI GI
TA L RIG connect the component (Y, P , P ) jacks
OU T S-V IDE HT B R
O
VID EO
VI DE LE FT with the player.
O OU P B
T
AU DI
O OU
T
White
Red
Connecting to a stereo audio amplifier (receiver)
P B
Y RIGHT
LEFT
EO VIDEO P R
VIDEO OUT AUDIO OUT
To analog audio input
Connecting to a digital audio device
To enjoy high-quality surround sound, connect the
DIGITAL OUT (COAXIAL) jack to a Dolby Digital or DTS
decoder or an amplifier with a built-in decoder.
P B
Y RIGHT
COAXIAL
PCM/STREAM
),""P " to "P (C )"
B R R R LEFT
S-VIDEO VIDEO P R
DIGITAL OUT VIDEO OUT AUDIO OUT
, P ) jacks, do not
B R
To analog
audio input
Video source
To digital audio input
[P]
NOTES
[DDP]
• Depending on the disc, no signal may be outputted
[P]
from the DIGITAL OUT. Make an analog connection
in this case.
• Set [DIGITAL AUDIO OUTPUT] in the [AUDIO]
preference display correctly according to the
connected digital audio equipment. (See "DIGITAL
AUDIO OUTPUT" in "Initial settings.")
4
Changing the picture tone (VFP)
The VFP (Video Fine Processor)
STANDBY/ON function allows you to adjust the
OPEN/
CLOSE
picture character according to the type
+ of programming, picture tone or
– SLOW DISPLAY ON SCREEN
personal preferences.
1 Press VFP-I/P.
2 Press 2/3 to select the desired
ENTER
preset.
Selected
USER 1
Preset
PREVIOUS SELECT NEXT
GAMMA MID
BRIGHTNESS + 4
CLEAR
+10
CONTRAST
SATURATION +10
1 2 3
TINT +10
4 5 6
SHARPNESS LOW
Y DELAY + 2
7 8 9
Parameter
CANCEL RETURN
0
NORMAL For watching TV in a general
TITLE/ SOUND room.
GROUP EFFECT VFP DIMMER
I/P
CINEMA For watching a movie
ANGLE SUBTITLE AUDIO ZOOM
software in a room with
suppressed light.
SLIDE EFFECT
USER1 You can adjust parameters
USER2 that affect the picture
character and store the
settings as a user preset.
See below.
To adjust the picture tone
1
Select "USER1" or "USER2."
Press 5/∞ to select a parameter, then press ENTER.
2
GAMMA Adjust this if the neutral color is bright or dark. The
brightness of dark and bright portion is maintained
(LOW/MID/HIGH).
BRIGHTNESS Adjust this if the picture is bright or dark on the
whole (–16 (darkest) to +16 (brightest)).
CONTRAST Adjust this if the far and near position is unnatural
(–12 to +12).
SATURATION Adjust this if the picture is whitish or blackish
(–16 (blackest) to +16 (whitest)).
TINT Adjust this if the appearance of flesh tone is
unnatural (–16 to +16).
SHARPNESS Adjust this if the picture is indistinct (LOW/HIGH).
Y DELAY Adjust this if the picture looks separately/
overlapped (–2 to +2).
Press 5/∞ to adjust the parameter, then press ENTER.
3
4
Repeat step 2 and 3 to adjust other parameters.
5 Press VFP-I/P to finish the setting.
8