JVC XV-N322S Instructions

DVD PLAYER
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
XV-N320B
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
XV-N322S
Caution –– STANDBY/ON button!
Disconnect the mains plug to shut the power off
INSTRUCTIONS
completely. The STANDBY/ON button in any
position does not disconnect the mains line. The power
® can be remote controlled.
IMPORTANT FOR LASER PRODUCTS
V I D E O
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover. There are no
user serviceable parts inside the unit; leave all
servicing to qualified service personnel.
GNT0059-017A[AG/AH/AX/AS/UM/AA]
3. CAUTION: Visible and invisible laser radiation when
EN 0205MOC-MW-SC
open and interlock failed or defeated. Avoid direct
©2005 Victor Company of Japan, Limited
exposure to beam.
Region code of DVD VIDEO
4. REPRODUCTION OF LABEL: CAUTION LABEL,
This player can play back DVD VIDEO discs
PLACED INSIDE THE UNIT.
whose region code numbers include the player's
Region Code, which is indicated on the region
code symbol on the rear panel.
Examples of playable DVD VIDEO discs:
1 2 1 2 3
2 2 5 CAUTION:
ALL
4 5 6
3 4 • Do not block the ventilation openings or holes. (If the
ventilation openings or holes are blocked by a
The player's region code is printed on the rear of
newspaper or cloth, etc., the heat may not be able to
the player
get out.)
Note of Color system format
• Do not place any naked flame sources, such as
This player is compatible with the PAL and NTSC
lighted candles, on the apparatus.
systems. Select the correct color system for your
• When discarding batteries, environmental problems
TV (see "Initial settings").
must be considered and local rules or laws
governing the disposal of these batteries must be
Supplied accessories
followed strictly.
If anything is missing, consult your dealer
• Do not expose this apparatus to rain, moisture,
immediately.
dripping or splashing and that no objects filled with
• Audio/video cable (Yellow/White/Red) (x 1)
liquids, such as vases, shall be placed on the
• Remote control (x 1)
apparatus.
• R6(SUM-3)/AA(15F) battery (x 2)
Caution: Proper Ventilation
• AC power plug adaptor (x 1)
To avoid risk of electric shock and fire and to protect
(Only for Singapore)
from damage, locate the apparatus as follows:
Front: No obstructions and open spacing.
Sides: No obstructions in 3 cm from the sides.
Top: No obstructions in 5 cm from the top.
Back: No obstructions in 15 cm from the back.
Bottom: No obstructions, place on the level surface.
Spacing 15 cm or more
XV-N320B/XV-N322S
Wall or
obstructions
1
Turning on the power Initial setup
When you turn on the player for the first time after
Inserting the AC power plug
purchase, the following message appears on the TV
After all other connections have been made, insert the
screen.
AC power plug to the wall outlet firmly.
EXECUTE DVD PLAYER SETUP? - BASIC PICTURE/AUDIO
SETTING
Installing the batteries in the remote control
YES - PRESS ENTER NO - PRESS CANCEL
Open the compartment cover, and place the two
Before enjoying this player, make the initial settings as
supplied R6(SUM-3)/AA(15F) batteries in the remote
follows:
control according to the polarity markings ("+" and "–")
inside the compartment. Then replace the cover. 1
Press ENTER.
DVD PLAYER SETUP
MENU LANGUAGE ENGLISH
AUDIO LANGUAGE ENGLISH
SUBTITLE ENGLISH
ON SCREEN LANGUAGE ENGLISH
ENGLISH
CHINESE
SPANISH
2 Press 5/∞ to select the on-screen language for
the preference displays, etc., then press ENTER.
DVD PLAYER SETUP
MONITOR TYPE 4:3 L.B.
16:9
PICTURE SOURCE AUTO
4:3 LB
4:3 PS
SCREEN SAVER ON
COLOUR SYSTEM PAL
The batteries will last about six months with normal use.
BACKGROUND STANDARD
If the functions of the remote control become erratic,
replace the batteries.
Press 5/∞ to select the monitor type, then press
3
Precautions of the safe use of batteries ENTER.
Observe the following precautions for the safe use of • For a normal (conventional) TV, select "4:3 LB" or
batteries. If they are used improperly their lives will be "4:3 PS." (See "MONITOR TYPE" in "Initial
shortened, they may burst or their contents may leak. settings.")
• Remove the batteries from the remote control if it is • For a wide-screen TV, select "16:9."
not going to be used for a long period of time.
DVD PLAYER SETUP
• Remove dead batteries and dispose of them
DIGITAL AUDIO OUTPUT DOLBY DIGITAL/PCM
properly.
PCM ONLY
ANALOG DOWNMIX DOLBY PROLOGIC
• Never leave dead batteries lying around, take them DOLBY DIGITAL/PCM
STREAM/PCM
D.RANGE CONTROL ON
apart, mix them with other refuse, or throw them into
OUTPUT LEVEL STANDARD
an incinerator.
• Never touch liquid that has leaked out of a battery.
• Do not mix new and old batteries, or batteries of
different types, when placing them. Press 5/∞ to select a desired digital output
4
signal type, then press ENTER.
Turning on and off the player Set this item correctly according to the logo on your
receiver or decoder.
Press STANDBY/ON.
(If you do not connect the player to such a device,
press ENTER to finish the setting.)
• Receiver/decoder bearing Dolby Digital logo and
no DTS, select "DOLBY DIGITAL/PCM."
• Receiver/decoder bearing both Dolby Digital and
DTS logos, select "STREAM/PCM."
• Receiver/decoder bearing neither Dolby Digital nor
DTS logo, or digital recorder, select "PCM ONLY."
To bring up the DVD PLAYER SETUP display later
Press SET UP for a few seconds until the DVD PLAYER
SETUP display appears.
5
Precautions Playable discs
Notes on the power cord
• DVD VIDEO, Audio CD, Video CD, SVCD
• When you are away on travel or otherwise for an extended
period of time, remove the plug from the wall outlet. A
small amount of power (1.0 W) is always consumed while
V I D E O
the power cord is connected to the wall outlet.
• DVD-R/-RW written in the DVD VIDEO format
• When unplugging the player from the wall outlet,
• CD-R/RW written in the SVCD, Video CD or Audio CD forma t
always pull the plug, not the power cord.
• CD-R/RW written in MP3/JPEG in accordance with
• Do not handle the power cord with wet hands!
the "ISO 9660" format
• Disconnect the power cord before cleaning the
Supported Digital audio formats:
player or moving the player.
Linear PCM, MPEG Multichannel, Dolby Digital, DTS (Digital
• Do not alter, twist or pull the power cord, or put
Theater Systems)*
anything heavy on it, which may cause fire, electric
NOTES
shock, or other accidents.
• If a disc gets dirty, scratched or warped, or due to the
• If the cord is damaged, consult a dealer and have the
disc characteristics or recording conditions, the
power cord replaced with a new one.
player may not be able to play back such discs.
Avoid moisture, water, dust, and high temperatures
• The player can play back audio signals recorded in
• Do not place the player in moist or dusty places.
MIX-MODE CD, CD-G, CD-EXTRA and CD TEXT.
• If water gets inside the player, turn off the power and • With some discs, operations may not be possible.
remove the plug from the wall outlet, then consult * To play back DTS-encoded DVD VIDEO or DTS-
your dealer. Using the player in this state may cause encoded Audio CD discs correctly, connect the
a fire or electrical shock.
player to an amplifier with a built-in DTS decoder.
• Do not expose the player to direct sunlight or place it
Otherwise, playback sound will be distorted.
near a heating device.
Unplayable discs
Notes on installation If you try to play back discs listed below, noise may be
• Select a place which is level, dry and neither too hot
generated and causes damage to speakers.
nor too cold between 5˚C and 35˚C.
• DVD-RW written in the VR format
• Leave sufficient distance between the player and the TV.
• DVD-ROM, DVD-RAM, DVD AUDIO, CD-ROM,
• Do not install the player in a place subject to vibrations.
PHOTO CD, SACD
• Do not put heavy objects on the player.
• Unfinalized discs
• Discs of irregular shape or discs with tape, seals or
To prevent malfunction of the player
paste on either the label side or playback side.
• There are no user-serviceable parts inside. If anything goes
Playing back these discs may damage the player.
wrong, unplug the power cord and consult your dealer.
• Do not insert any metallic objects, such as wires,
The Non-DVD side of a "DualDisc" does not comply with
hairpins, coins, etc. into the player.
the "Compact Disc Digital Audio" standard.
• Do not block the vents. Blocking the vents may
Therefore, the use of Non-DVD side of a DualDisc on
damage the player.
this product may not be recommended.
To clean the cabinet
• Use a soft cloth. Follow the relevant instructions on
the use of chemically-coated cloths.
• Do not use benzene, thinner or other organic solvents and
disinfectants. These may cause deformation or discoloring.
Front
Stand height
5 cm or more
Floor
2
Basic Operations
Insert a disc
Press 0 to open the disc tray.
1
2
Place a disc in the disc tray.
Turning on and off the player
• To insert an 8-cm disc, place it in the inner
recess.
Press 0 to close the disc tray.
3
Point toward the remote sensor directly as possible
(the operating range is approx. 5 m.)
About On-screen guide icons
: Playback.
: Pause.
Main display / : Slow-motion playback with the current
• Each indicator lights up when corresponding
function/mode is activated, or corresponding
/ : Fast forward/backward playback with the
information is on the main display.
current speed.
: At the beginning of a scene containing multi-
angle views.
: At the beginning of a scene containing multi-
audio sounds.
: At the beginning of a scene containing multi-
subtitles.
You can change the setting so that the on-screen
guide icons do not appear on the TV screen. (See
"ON SCREEN GUIDE" in "Initial settings.")
6
Connections
Before making connections:
• Do not connect the AC power cord until all other connections have been made.
• Connect VIDEO OUT of the player directly to the video input of your TV. Connecting VIDEO OUT of the
player to a TV via a VCR/an integrated TV/Video system may cause a monitor problem.
Basic Connection
S-video cable*
(not supplied)
PC M
/S TR CO AX
EA M
Yellow
DI GI
TA L
OU T
Audio/video
cable*
(supplied)
Red
Connecting to a TV with component jacks
P
B
Y RIGHT
OAXIAL
REAM
LEFT
S-VIDEO VIDEO R P
OUT VIDEO OUT AUDIO OUT
To component video input
To switch the scanning mode between Progressive and
Interlace, press and hold VFP-I/P on the remote control
for a few seconds.
NOTES
• Connect "Y" to "Y,""P " to "P (C ),""P
B B B
correctly.
• When using the component (Y, P B , P R
connect the S-VIDEO jack with the player.
Turning on and off the player
Open/close the disc tray
Basic playback
Buttons To do
3*
Start/resume normal Playback
7
Stop
• When RESUME is ON or DISC
RESUME, this player memorizes
the position on the disc where
you interrupted playback.
– To resume playback, press 3.
– To stop playback completely,
press 7 again.
8*
Pause
• Each time you press 8 on the
remote control, the still picture
advances to the next frame.
¡/1 Fast forward/backward
(While paused)
Slow-motion playback
• Each time you press the button,
the playback speed changes.
With the label side up
¢/4 Skip chapter/track
• If you press and hold the button
during playback, playback is
advanced/reversed at 5 times
normal speed.
VARIABLE (For DVD Video)
PLAYBACK
The disc is played back at about
/VARI-PLAY
1.2 or 1.5 times (FAST)/0.8 or 0.6
times (SLOW) normal speed.
The sound is not muted, and the
subtitle does not go off (except for
DTS).
(For SVCD/VCD)
The disc is played back at about 2
times (FAST)/0.5 times (SLOW)
speed.
normal speed.
(Only for DVD Video)
The playback position moves
back 10 seconds before the
current position (only within the
same title).
* 38 on the player starts/pauses playback.
Changing the display brightness
Press DIMMER to change the brightness of
the display window.
Connecting to a stereo audio amplifier (receiver)
P B
Y
RIGHT
LEFT
IDEO VIDEO P R
VIDEO OUT AUDIO OUT
TV
NOTES Connecting to a digital audio device
• Set the correct color system according to To enjoy high-quality surround sound, connect the
IN
DIGITAL OUT (COAXIAL) jack to a Dolby Digital or DTS
S- VI the color system your TV supports. (See
DE O
decoder or an amplifier with a built-in decoder.
"COLOUR SYSTEM" in "Initial settings.")
V ID
E O
• If your TV has a monaural audio input
instead of stereo, use an optional audio COAXIAL
LE FT PCM/STREAM
cable which converts stereo audio output
A U D
IO
RI GH to monaural.
S-VIDEO
T
DIGITAL OUT
• If your TV is a HDTV or HD-ready TV, you
can connect with component (Y, P , P )
B R
jacks. By connecting with component (Y,
P , P ) jacks, you can select the
B R
IAL The player progressive scanning mode which provides
To digital audio input
Y P R
the best picture quality.
S-V IDE * The S-VIDEO jack and the component (Y,
O RIG NOTES
VID EO HT
VI DE
O OU P P B , P R ) jacks cannot be used at the same
B
T • Depending on the disc, no signal may be outputted
LE FT
AU DI time.
O OU from the DIGITAL OUT. Make an analog connection
T
CO MP AV
When using the S-VIDEO jack, do not
U LIN
K in this case.
connect the component (Y, P , P ) jacks
B R
White • Set [DIGITAL AUDIO OUTPUT] in the [AUDIO]
with the player.
preference display correctly according to the
connected digital audio equipment. (See "DIGITAL
AUDIO OUTPUT" in "Initial settings.")
About the scanning mode indicator
[PICTURE SOURCE] of Source type of DVD VIDEO
Using the AV COMPU LINK system
the PICTURE menu
Film source Video source
The AV COMPU LINK system allows you to enjoy video
AUTO [DDP] [P]
and/or audio by simply pressing Play on the source
FILM [DDP] [DDP]
component (the component which plays back the video
VIDEO(NORMAL)/
[P] [P]
or audio, such as a DVD player or VCR). You
(ACTIVE)
do not even have to switch on power on the TV or
NOTE
receiver.
Some progressive TV and High-Definition TV sets are
not fully compatible with the player. To check the
Connection and setup
compatibility of your TV, contact your local JVC
Using an AV COMPU LINK cable, connect the AV
customer service center.
COMPU LINK terminals of each component to one
another.
" to "P (C )"
R R R
• The player's AV COMPU LINK setting is controlled
using the OTHERS menu in the preference display.
) jacks, do not
See "AV COMPULINK MODE" in "Initial settings."
• See also the instruction manual of the other device.
3
Advanced Operations
Changing the display window Changing the language, sound
contents
and scene angle
Each time you press DISPLAY,
1 Press the button.
STANDBY/ON
OPEN/ the display window contents
2
CLOSE Press the button repeatedly or
changes. 5/∞ to select the desired item.
– SLOW + DISPLAY ON SCREEN
3
Press ENTER to finish the
Locating the beginning of a scene setting.
or song
Buttons
You can select a title/chapter/
ENTER
AUDIO
track directly and start playback.
For DVD Video:
(While stopped) select title.
PREVIOUS SELECT NEXT
(While playing back) select
CLEAR chapter.
SUBTITLE
For SVCD/VCD/CD:
Select track.
1 2 3 ANGLE
To select 5: press 5.
4 5 6
To select 23: press 2, then 3.
To select 40: press 4, then 0.
7 8 9
Changing the Sound Field
CANCEL RETURN • If you press TITLE/GROUP
0
Each time you press SOUND
before entering the number, you
TITLE/ SOUND EFFECT, the Sound Effect mode
can select the title instead of the
GROUP EFFECT VFP DIMMER
I/P changes.
chapter.
• As the value becomes bigger, the
ANGLE SUBTITLE AUDIO ZOOM
Sound Effect works stronger.
Using the disc menu
SLIDE EFFECT
You can operate a disc—SVCD/
VCD with Playback Control*
(PBC)—using the disc menu
shown on the TV screen. Zooming the picture
* A method of controlling disc play
Each time you press ZOOM, the
for SVCD/VCD by using the disc
magnification changes.
menu.
• You can use 5/∞/2/3 button to
7 For DVD
move the zoomed position.
1 Press TOP MENU or MENU to show the disc menu.
To return to the normal playback,
2 Press 5/∞/2/3 to select a desired item, then press
select the normal size by pressing
ENTER or 3 (SELECT).
ZOOM repeatedly.
• With some discs, you can also select items by entering the
number using the numeric buttons.
7 For SVCD/VCD
While stopped, press TOP MENU or 3 (SELECT) to
1
show the menu.
2
Press the numeric buttons to select a desired item.
To select 5: press 5.
To select 23: press 2, then 3.
To select 40: press 4, then 0.
• To move to the next or previous page of the current menu,
press ¢ or 4.
• To return to the previous menu, press RETURN.
To play back without PBC
While stopped, press the numeric buttons instead of 3
(SELECT) to start playback.
To reactivate PBC
• Press TOP MENU or MENU.
• Press 7 to stop playback, then 3 (SELECT).
7
EX. 1
To AV COMPU LINK (II, EX, or III)
TV
The player
To analog audio input
• Set the player's AV COMPU LINK setting as follows:
– When connecting to the VIDEO-1 input terminal of
the television: DVD2
– When connecting to the VIDEO-2 input terminal of
the television: DVD3
P B
Y EX. 2
RIGHT
To AV COMPU LINK To AV
LEFT
VIDEO P R
AUDIO OUT (II, EX, or III) COMPU LINK
VIDEO OUT
To analog
audio input
TV
The player
• Set the VCR's Remote Control Code and the player's
AV COMPU LINK setting as follows:
– When connecting to the VIDEO-1 input terminal of
the television:
The player's AV COMPU LINK setting: DVD2
VCR's Remote Control Code: B
– When connecting to the VIDEO-2 input terminal of
the television:
The player's AV COMPU LINK setting: DVD3
VCR's Remote Control Code: A
EX. 3
To AV COMPU LINK To AV
(II, EX, or III) COMPU LINK
TV
Receiver The player
• Set the player's AV COMPU LINK setting to DVD1.
Notes for connection
• If you connect the player to a receiver via AV COMPU
LINK in a system including a Dolby Digital decoder,
some functions may not be performed automatically.
• Connect the AUDIO OUT jacks of the player to the
audio input jacks of a receiver indicating "DVD."
Otherwise, the system will not work correctly.
Operation
1. Turn on the main power of the television.
2. Insert a disc (or tape) into the source component.
3. Press 3 of the source component.
The following actions are performed automatically:
• Turning on the television and/or receiver.
• Setting the source of the television to the external
input (VIDEO-1 or VIDEO-2).
• Setting the source of the receiver to the component
which has started playback.
4
Changing the picture tone (VFP)
The VFP (Video Fine Processor)
STANDBY/ON function allows you to adjust the
OPEN/
CLOSE
picture character according to the type
+ of programming, picture tone or
– SLOW DISPLAY ON SCREEN
personal preferences.
1 Press VFP-I/P.
2 Press 2/3 to select the desired
To do
ENTER
preset.
For DVD Video:
Selected
select audio languages.
USER 1
Preset
For SVCD/VCD:
PREVIOUS SELECT NEXT
GAMMA MID
select the audio
BRIGHTNESS + 4
channel. CLEAR
+10
CONTRAST
select the subtitle.
SATURATION +10
1 2 3
TINT +10
select the view-angle.
4 5 6
SHARPNESS LOW
Y DELAY + 2
7 8 9
Parameter
CANCEL RETURN
0
NORMAL For watching TV in a general
TITLE/ SOUND room.
GROUP EFFECT VFP DIMMER
I/P
CINEMA For watching a movie
ANGLE SUBTITLE AUDIO ZOOM
software in a room with
suppressed light.
SLIDE EFFECT
USER1 You can adjust parameters
USER2 that affect the picture
character and store the
settings as a user preset.
See below.
To adjust the picture tone
1
Select "USER1" or "USER2."
Press 5/∞ to select a parameter, then press ENTER.
2
GAMMA Adjust this if the neutral color is bright or dark. The
brightness of dark and bright portion is maintained
(LOW/MID/HIGH).
BRIGHTNESS Adjust this if the picture is bright or dark on the
whole (–16 (darkest) to +16 (brightest)).
CONTRAST Adjust this if the far and near position is unnatural
(–12 to +12).
SATURATION Adjust this if the picture is whitish or blackish
(–16 (blackest) to +16 (whitest)).
TINT Adjust this if the appearance of flesh tone is
unnatural (–16 to +16).
SHARPNESS Adjust this if the picture is indistinct (LOW/HIGH).
Y DELAY Adjust this if the picture looks separately/
overlapped (–2 to +2).
Press 5/∞ to adjust the parameter, then press ENTER.
3
4
Repeat step 2 and 3 to adjust other parameters.
5 Press VFP-I/P to finish the setting.
8
VCR