Motorola DS4208 Quick Start Manual page 3

INTELLISTAND
SCANNER INDICATIONS
LED Indications
Standard Use
Off Green
Scanner is on and ready to scan, Bar code is
or no power to scanner successfully decoded
Beeper Indications
Standard Use
Low/medium/high beeps Short beep
Power up Bar code symbol decoded
(if decode beeper enabled)
High/low beeps
High/low/high/low beeps
Successful Keyboard parameter
parameter setting selected.
Avoid Extreme Wrist Angles
AVOID EXTREME
WRIST ANGLES
© 2011 MOTOROLA, Inc. All rights reserved.
Motorola reserves the right to make changes to any product to improve reliability, function, or design.
Motorola does not assume any product liability arising out of, or in connection with, the application or use of any
product, circuit, or application described herein. No license is granted, either expressly or by implication,
estoppel, or otherwise under any patent right or patent, covering or relating to any combination, system,
apparatus, machine, material, method, or process in which Motorola products might be used. An implied license
exists only for equipment, circuits, and subsystems contained in Motorola products.
Power Supply
given to this unit and may be dangerous.
Warranty
For the complete Motorola hardware product warranty statement, go to:
http://www.motorola.com/enterprisemobility/warranty.
Service Information
If you have a problem using the equipment, contact your facility's Technical or Systems Support. If there is a
problem with the equipment, they will contact the Motorola Solutions Support at:
http://supportcentral.motorola.com.
For the latest version of this guide go to: http://supportcentral.motorola.com.
Waste Electrical and Electronic Equipment (WEEE)
Motorola, Inc. One Motorola Plaza , Holtsville, New York 11742-1300, USA
http://www.motorola.com
MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M Logo are trademarks or
registered trademarks of Motorola Trademark Holding, LLC and are used under license.
All other trademarks are the property of their respective owners.
© 2011 Motorola, Inc. All rights reserved.
DS4208
SET DEFAULTS
SET DEFAULTS
Troubleshooting
Scanner not working
Red
No power to scanner
Transmission error
Check system power;
ensure power supply,
if required, is connected
4 low beeps
Scanner decoding bar code, but data not transmitting to host
Scanner not programmed for correct host interface
Transmission error detected,
data is ignored
Scan appropriate host parameter bar codes
Low/high beeps
Input error; incorrect bar code,
programming sequence, or Cancel
scanned
RECOMMENDED USAGE GUIDE - OPTIMUM BODY POSTURE
Avoid Bending
REGULATORY INFORMATION
Scanner Labeling
http://www.motorola.com/ds4208
OPTIMUM SCANNING
TROUBLESHOOTING
Incorrect interface cable used Interface/power cables are loose
Ensure that correct Ensure all cable connections
interface cable is used are secure
Interface cable is loose
Ensure all cable connections
are secure
Avoid Reaching
AVOID BENDING
123SCAN
123Scan is an easy-to-use, PC-based software
2
tool that enables rapid and easy customized
setup via a bar code or USB cable. For more
information, visit:
http://www.motorola.com/123Scan
Scanned data incorrectly displayed on host
Scanner not programmed for correct host interface
Scan appropriate host parameter bar codes
Scanner not decoding bar code
Scanner not programmed Bar code unreadable
for bar code type
Ensure bar code not defaced;
Ensure scanner is programmed
try scanning test bar code
to read type of bar code being
of same bar code type
scanned
Health and Safety Recommendations
Ergonomic
Recommendations
Caution: In order to avoid or minimize the potential risk of ergonomic
injury follow the recommendations below. Consult with your local
Health & Safety Manager to ensure that you are adhering to your
company's safety programs to prevent employee injury.
or eliminate repetitive motion.
AVOID REACHING
Regulatory Information
This device is approved under Motorola, Inc. ("Motorola").
This guide applies to Model Number: DS4208.
All Motorola devices are designed to be compliant with rules and regulations in locations they are sold
and will be labeled as required.
Local language translations are available at the following website: http://supportcentral.motorola.com.
Any changes or modifications to Motorola Technologies equipment, not expressly approved by
Motorola, could void the user's authority to operate the equipment.
Antennas: Use only the supplied or an approved replacement antenna. Unauthorized antennas,
modifications, or attachments could cause damage and may violate regulations.
LED Devices
Complies with IEC/EN60825-1:2001 & IEC/EN62471:2006
For devices with Class 1M LEDs the following label is used:
Radio Frequency Interference Requirements -FCC
Note: This equipment has been tested and found to comply with the
Tested to comply limits for a Class B digital device, pursuant to Part 15 of the FCC rules.
with FCC Standards
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
receiver is connected
Radio Frequency Interference Requirements - Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Marking and European Economic Area (EEA)
Statement of Compliance
Motorola hereby declares that this device is in compliance with all the applicable Directives,
2004/108/EC and 2006/95/EC. A Declaration of Conformity may be obtained from
http://www.motorola.com/doc.
TURKISH WEEE Statement of Compliance
EEE Yönetmeliğine Uygundur
Japan (VCCI) - Voluntary Control Council for Interference
Class B ITE
Korea Warning Statement for Class B ITE
2
.
2
Distance between scanner
and bar code incorrect
Move scanner closer to or
further from bar code
B