Subscribe to Our Youtube Channel
Related Manuals for Maktec MT362
Summary of Contents for Maktec MT362
- Page 1 INSTRUCTION MANUAL Router MT362 013290 DOUBLE INSULATION IMPORTANT: Read Before Using.
-
Page 2: Specifications
ENGLISH (Original instructions) SPECIFICATIONS Model MT362 Collet chuck capacity 12 mm or 1/2" Plunge capacity 0 - 60 mm No load speed (min 22,000 Overall height 300 mm Net weight 5.5 kg Safety class • Due to our continuing program of research and development, the specifications herein are subject to change without notice. - Page 3 Designation of Machine: atmospheres, such as in the presence of Router flammable liquids, gases or dust. Power tools Model No./ Type: MT362 create sparks which may ignite the dust or fumes. are of series production and Keep children and bystanders away while Conforms to the following European Directives: operating a power tool.
-
Page 4: Router Safety Warnings
Personal safety 22. Maintain power tools. Check for misalignment Stay alert, watch what you are doing and use or binding of moving parts, breakage of parts common sense when operating a power tool. and any other condition that may affect the Do not use a power tool while you are tired or power tool’s operation. -
Page 5: Functional Description
Be careful of the bit rotating direction and the FUNCTIONAL DESCRIPTION feed direction. 12. Do not leave the tool running. Operate the tool only when hand-held. CAUTION: 13. Always switch off and wait for the bit to come Always be sure that the tool is switched off and •... -
Page 6: Operation
CAUTION: ASSEMBLY Since excessive cutting may cause overload of the • motor or difficulty in controlling the tool, the depth CAUTION: of cut should not be more than 20 mm at a pass Always be sure that the tool is switched off and when cutting grooves. - Page 7 Set the tool base on the workpiece to be cut without the Straight guide (Type A) (Optional accessory) bit making any contact. Then turn the tool on and wait 1. Thumb screw until the bit attains full speed. Lower the tool body and move the tool forward over the workpiece surface, 2.
- Page 8 Trimmer guide (Type A) (Optional accessory) Templet guide 1. Thumb screw (A) 2. Guide holder 3. Fine adjusting screw 4. Thumb screw (B) 5. Thumb screw (C) 6. Trimmer guide 7. Guide roller 013305 013301 Install the trimmer guide on the guide holder with the The templet guide provides a sleeve through which the thumb screw (B).
-
Page 9: Maintenance
Dust cover (For tool with the knob) (optional 1. Support accessory) 2. Lock lever 1. Screw 2. Dust cover 004940 Then connect a vacuum cleaner to the vacuum head. 013307 Dust cover prevents sawdust from being drawn into the tool in the inverted position. Install the dust cover as illustrated when using the tool with a router stand available in the market. -
Page 10: Optional Accessories
For tool with the knob OPTIONAL ACCESSORIES CAUTION: Router bits Be sure to re-install the knob after inserting new • Straight bit carbon brush. 1. Knob 005116 013310 Release the lock lever and remove the knob by turning it counterclockwise. The compression spring will come out of the knob, so be careful not to lose the 1/4"... - Page 11 "V"Grooving bit Drill point double flush trimming bit 005118 005121 1/4" 006454 006457 Dovetail bit Slotting cutter 005119 005122 14.5 15SE 3/8" 1/2" 14.5 14.5 15LE 3/8" 1/2" 006458 3/8" 006455 Drill point flush trimming bit 005120 006456...
- Page 12 Board-jointing bit Chamfering bit 005123 005126 1/2" 006461 005124 006459 005127 Corner rounding bit 006462 Beading bit 005125 006460 005128 1/2" 006463...
- Page 13 Cove beading bit Ball bearing chamfering bit 005132 005129 1/4" 006464 Ball bearing flush trimming bit 006467 Ball bearing beading bit 005130 005133 1/4" 006465 Ball bearing corner rounding bit 006468 Ball bearing cove beading bit 005131 005134 1/4" 006466 006469...
- Page 14 Ball bearing roman ogee bit 005135 006470 Double ball bearing round corner bit 005136 1/2" 006471...
- Page 16 Makita Corporation Anjo, Aichi, Japan www.makita.com 885173A224...
Need help?
Do you have a question about the MT362 and is the answer not in the manual?
Questions and answers