CLF 26 Contents GENERAL INFORMATION ______________________________________________________ 2 Documentation supplied with the machine ____________________________________________ 2 General notes ___________________________________________________________________ 2 Important safety notes ____________________________________________________________ 3 GETTING TO KNOW YOUR MACHINE____________________________________________ 4 Control panel ___________________________________________________________________ 4 Installation data _________________________________________________________________ 4 INSTALLATION________________________________________________________________ 5 Glossary________________________________________________________________________ 5...
CLF 26 GENERAL INFORMATION GENERAL INFORMATION AILURE TO COMPLY WITH THE INSTRUCTIONS PROVIDED MAY COMPROMISE THE SAFETY OF THE APPLIANCE AND WILL INVALIDATE THE WARRANTY WITH IMMEDIATE EFFECT Documentation supplied with the machine This manual contains important information regarding safety during the installation, use and maintenance of the appliance.
GENERAL INFORMATION CLF 26 Important safety notes The appliance is designed for professional use and notwithstanding the manufacturer’s efforts to simplify its operation, installation and maintenance, the appliance is designed for operation by trained personnel in compliance with the manufacturer’s instructions. Do not allow children to operate or play with the machine.
CLF 26 GETTING TO KNOW YOUR MACHINE GETTING TO KNOW YOUR MACHINE Control panel [1] = Power on/off switch and pilot light» [2] = Start button [3] = “Wash cycle” pilot light [4] = “Heating” pilot light [5] = Cold rinse (optional)
CLF 26 INSTALLATION INSTALLATION HE MANUFACTURER ACCEPTS NO LIABILITY FOR ANY DAMAGE TO OBJECTS OR PERSONAL INJURY ARISING FROM INSTALLATIONS WHICH FAIL TO COMPLY WITH THE INSTRUCTIONS PROVIDED Glossary In this document, the terms Main switch, water supply stop cock and Drain line are defined...
CLF 26 INSTALLATION Unpacking the appliance Before removing the packaging, check for any signs of damage, noting any defects found on the carrier’s delivery note After removing the packaging inspect the appliance for signs of damage; if damaged, notify your...
Page 9
To ensure unrestricted discharge the pipe must reach the trap without being put under tension, kinked, crushed, pressed or forced. (Model CLF 26 - supplied with Drain Pump as standard) If the discharge pipe is connected to a trap in the floor, the highest point of the pipe must be at least 300 mm above floor level to prevent the machine from emptying.
CLF 26 INSTALLATION Dispenser settings Rinse-aid dispenser Before starting the washing cycle, the dispenser and the delivery pipe must be full. Check that there is sufficient rinse-aid in the container and top up if necessary. The rinse-aid container must never be allowed to empty completely and must not be topped up with corrosive or impure products.
Page 11
CLF 26 INSTALLATION not lead to any significant improvement. To remove this patina, the tableware is to be left to soak in a water and soap solution (10:1) for about 30 minutes and then washed again. Detergent dispenser (optional) Never allow the detergent container to empty completely and never top up with corrosive or impure products.
CLF 26 INSTALLATION On completion of the filling cycle and before the wash cycle has started, open the door and pour the previously determined quantity of detergent into the chamber in the region of the wash pump suction filter. About 10 seconds after the start of the wash cycle, start turning the potentiometer in a clockwise direction until you hear a buzzing which indicates that the dispenser is delivering detergent to the chamber.
CLF 26 USE AND MAINTENANCE USE AND MAINTENANCE Safety notes HE MANUFACTURER ACCEPTS NO LIABILITY FOR ANY DAMAGE TO OBJECTS OR PERSONAL INJURY ARISING FROM FAILURE TO COMPLY WITH THE INSTRUCTIONS PROVIDED Precautions The correct operation and the service life of the appliance depend on external factors including preventive maintenance, the characteristics of the water supply and the products used for washing, rinsing and cleaning.
USE AND MAINTENANCE CLF 26 Hygiene To ensure the hygiene of the machine, it is important to carry out the periodic maintenance operations indicated in the relative section of this manual. The appliance must also be regularly sanitized using suitable non-corrosive commercial products.
CLF 26 USE AND MAINTENANCE Before starting the machine, check that it has been installed correctly by a qualified technician in compliance with all the indications contained in the documentation supplied with the appliance. Dispensers for rinse-aid and detergent (optional) Before starting the wash cycle, the dispensers and the dispensing pipes must be full.
CLF 26 USE AND MAINTENANCE 6. Only load items which are guaranteed suitable for dishwashers and which are free from cracks. 7. Load the rack into the appliance and close the door. 8. Select the desired cycle with button [7]. Press button [2] to start the wash cycle.
CLF 26 USE AND MAINTENANCE For appliances without detergent dispensers only. If five cycles have already been performed, add detergent in the region of the washing pump suction filter in the amount indicated by the detergent manufacturer and the installation manual.
Page 18
CLF 26 USE AND MAINTENANCE • Clean the machine using a damp rag with a little detergent. • Do not use scouring pads, wire brushes or abrasive cleaning products to clean the steel surfaces. If the machine is not to be used for a period, leave the door slightly ajar to prevent unpleasant odors from forming.
CLF 26 USE AND MAINTENANCE Solutions to the most common problems Dishes not clean ROBLEM EMEDY Wash arms stuck. The arms should rotate easily by hand. Pull arms off and clean carefully. Check and clean the arms supply pipe in the machine.
Page 20
USE AND MAINTENANCE CLF 26 Water softener(Optional) ROBLEM EMEDY Excess salt in rinse water. Salt left in container after regeneration. Only fill container immediately before starting the regeneration cycle with the quantity of salt indicated in the operating instructions. Wrong size salt grains. Use salt with a grain size of 1 - 2 mm Excessive salinity after resin regeneration.
Page 21
Avec doseur produit de lavage Con dosatore detergente 400V 3N~ 230V 3~ 230V ~ 230V ~ File Supds. dwg. Date Dwn.by Mod. Drawing n. CLF 26 File Ersetzt Datum Gezeichn Mod. Zeichnungh n. 784MANON.CAD 13-06-2001 Fragnan L. 784/Sc File Remplace...
Page 22
Y7 Break tank solenoid valve Electrovanne niveau "Air Gap" Elettrovalvola livello "Air Gap" Válvula magnetica de "Air Gap" Válvula magnetica de "Air Gap" Gap" Z1 Interference suppression filter Funkenstörfilter Filtre antiparasite Filtro antidisturbo Filtro antiparasitario Filtro de ruídos CLF 26...
Page 24
As continued product improvement is a policy of HOBART, specifications are subject to change without notice. Ce catalogue n’est pas contractuel. HOBART se réserve le droit, et sans préavis, d’apporter toutes modifications ou améliorations à ses matériels. HOBART behält sich das Recht vor, an allen Produkten technische Änderungen und Verbesserungen ohne Ankündigung vorzunehmen.10.03.2003-Issue-1...