Related Manuals for Hobart Ecomax 502L
Summary of Contents for Hobart Ecomax 502L
- Page 1 GLASS- AND DISHWASHERS ECOMAX 502L(P) INSTALLATION AND OPERATION INSTRUCTIONS (original instructions) V1.7 2013.01.28 V1.6 2012.09.04...
-
Page 2: Important Notes
IMPORTANT NOTES THE ORIGINAL INSTRUCTIONS. ONLY TRAINED OR AUTHORIZED ADULT PERSONS OPERATE THE MACHINES. USE IN ACCORDANCE WITH REGULATIONS The machine is technical work equipment for express use in the work place. The machine is exclusively to be used to wash ware such as plates, cups, glasses, cutlery, trays etc. Do not use for electrically heated cooking and heat conservation appliances. - Page 3 (minimum 10 g of detergent per liter). As continued product improvement is a policy of HOBART, specifications are subject to change without notice. Company address: No.8 Yesheng Road, Xiqing Economic & Development Zone, Tianjin China.
-
Page 4: Table Of Contents
CONTENTS Page BRIEF INTRODUCTION ..........5 TRANSPORTATION, STORAGE AND INSTALLATIONS ..6 2.1. transportation and storage ..............6 2.2. Location .....................6 2.3. Electrical connection................6 2.4. Water connection ................7 2.5. Drain connection .................7 CONTROLS ..............8 START-UP ..............9 4.1. Detergent PUMP (OPTIONAL) ..............9 4.2. Rinse aid PUMP (OPTIONAL) ..............9 4.3. -
Page 5: Brief Introduction
BRIEF INTRODUCTION Introduction table: Filling connection G3/4 Tank drain DN20 Power line Detergent dosage Rinse aid dosage... -
Page 6: Transportation, Storage And Installations
TRANSPORTATION, STORAGE AND INSTALLATIONS 2.1. TRANSPORTATION AND STORAGE Folklift must be used during transportation and storage instead of vertical loading, pay attention to upturn and prevention of break, moisture and load. (See the marks on the package). 2.2. LOCATION – Rear wall clearance not required. –... -
Page 7: Water Connection
TRANSPORTATION, STORAGE AND INSTALLATIONS 2.4. WATER CONNECTION Must be carried out by an authorized technician according to the national and local codes. The machine must be operated with potable water. For water with an extremely high mineral content an external deminerali- sation is strongly recommended –... -
Page 8: Controls
CONTROLS ➀ Machine ON/STOP button Pushing this button switches the machine on. The LED lights up − flashing = Machine is filling and heating. − permanent = Maschine is ready to operate. In case of operating error or faults, it is possible to switch-off the machine im- mediately without the drain cycle, by pushing this button. -
Page 9: Start-Up
START-UP Attention: The maximum suction head of the dosing pumps is 1.5 m. Do not confuse the containers Use only detergent and rinse aid for commercial applications. Please pay attention to the manufacturer’s safety instructions. NOTE: Before changing to a different product type (even from the same supplier), the suction hoses must be rinsed thoroughly with fresh water (procedure as described under section 4.3.). -
Page 10: Priming The Suction Hoses
START-UP 4.3. PRIMING THE SUCTION HOSES ATTENTION: The machine has to be switched off. – Open the door. ➁ – Push Program buttons simultaneously. • LEDs light up. • In display ➇ , the LEDs 1 and 11−20 illuminate (dependent on basic setting). -
Page 11: Softener (Optional)
START-UP 4.4. SOFTENER (OPTIONAL) NOTE: For the first run, the softener has to be filled with regenera- tion salt and potable water. Attention: Filling the salt reservoir with cleaning agent will damage the water softener. – Open the door. – Unscrew the softener lid and fill the softener with 1.5 kg of “Granu- lar regeneration salt”... -
Page 12: Operation
OPERATION 5.1. PREPARATION – Check correct position of wash/rinse arms, strainer and overflow pipe. – Open shut-off valve. – Switch on main switch or put the plug in. – Check level of detergent and rinse aid containers. ➀ – Close door and push the ON button • tank will be filled. -
Page 13: Run
OPERATION 5.2. – Put rack into the machine and close the door. – Start the desired program by selecting the program button 1 or 2 Button "1" = Short cycle Button "2" = Standard cycle • The Program button LED flashes, wash cycle is running. • As soon as the LED changes to steady light, the wash cycle is finished. -
Page 14: Switch-Off And Cleaning The Machine
SWITCH-OFF AND CLEANING THE MACHINE 6.1. SWITCH-OFF – Versions with overflow pipe: remove – Close the door. – Push and hold (min. 3 seconds) the Drain button ➂ • LED lights up. The self-cleaning cycle will be started and the machine interior is cleaned automatically. -
Page 15: Settings
SETTINGS ATTENTION: The machine has to be switched off. – Open the door. If the door will be closed or if no button is pressed for 30 seconds,the indicator automatically switches off and the new settings will be saved. Therefore the setting procedure can be interrupted at any time. 7.1. -
Page 16: Adjustment Of Water Hardness
SETTINGS 7.3. ADJUSTMENT OF WATER HARDNESS – With optional softener only. – To adjust the softener to the local water hardness (obtain details from local water authorit): – Push Program button “1”. LEDs 1 to 3 illuminate in the left display –... -
Page 17: Frost Prevention
FROST PREVENTION This should be carried out by service personnel! In case of frost or longer operation pauses (e.g. for seasonal operations) the machine must be completely drained. Reset for operation according to section section 3.. -
Page 18: Maintenance
MAINTENANCE In order to maintain the warranty, as well as a permanently safe, efficient, and trouble-free operation of the machine, the required maintenance must be carried out by authorized service technicians. For this reason, we recommend the conclusion of an inspection and maintenance contract which assures qualified support by specially trained service technicians according to a time scheduled based on the operating conditions. -
Page 19: Troubleshooting Guide
TROUBLESHOOTING GUIDE 10.1. POOR WASH RESULT REMEDY TYPE OF FAILURE POSSIBLE CAUSE Washware are not clean. Wash arms stiff (you should be able to Take out wash arms and clean them thoroughly. turn them easily by hand). Check water outlet from machine to wash arms is clear. -
Page 20: 10.2. Other Faults
TROUBLESHOOTING GUIDE 10.2. OTHER FAULTS TYPE OF FAILURES POSSIBLE CAUSE REMEDY Glasses are totally or partially Surface of glasses is rough and porous, This is not caused by a malfunction on the machine. cloudy this is called glass corrosion Replace with new glasses. Glass breakages. - Page 22 HOBART China No.8 Yesheng Road, Xiqing Ecomonic & Development Zone, Tianjin China Tel. 022-23974912/13/14/15 Fax 022-23974917 E-Mail: info@hobart.cn As continued product improvement is a policy of HOBART, Internet: www.hobart.cn specifications are subject to change without notice. Printed in China...
- Page 23 Dishwasher Maintenance For AMX/AM900 H502L/E502L AM50E/AM60E Clean machine(Customer) Items Content Tank flat strainer Visual inspection & cleaning Wash tank housing Visual inspection (lime deposits etc.) Wash & rinse arms Removing & cleaning of upper and lower wash arms. Tighten screws when installing. Overflow &...