Cannon Fitzroy Inbuilt Power Flue Instruction Manual
Cannon fitzroy inbuilt power flue instruction manual
Hide thumbs
Also See for Fitzroy Inbuilt Power Flue:
- User instructions (12 pages) ,
- Operation instructions manual (14 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Instructions for Using
Advertisement
Table of Contents
Related Manuals for Cannon Fitzroy Inbuilt Power Flue
Summary of Contents for Cannon Fitzroy Inbuilt Power Flue
- Page 1 Fitzroy Inbuilt Power Flue Instruction Manual Please read this manual before installing and using this heater. Please leave instruction manual with the owner Distributor This appliance is designed, manufactured and distributed by: Tel: 1300 727 421...
-
Page 2: Table Of Contents
Practices act and similar laws of the States and territories. We warrant this Cannon appliance to be free of defects in materials, workmanship and manufacturing to the original purchaser for 2 years, (10 years on the heat exchanger) from the date of original purchase. -
Page 3: Safety Warnings
CannOn distributor of sound construction. listed in this manual. -
Page 4: Operation
Do not use this fire if the glass is cracked or with heater on. the safety screen removed. Do not use fire with broken or missing logs. ON / OFF MEDIUM HIGH fig 1 fig 2 4 | Cannon Fitzroy Inbuilt Power Flue... -
Page 5: Optional Accessories
Install in a shallow recess or an existing fireplace, elegant spacers will eliminate any size discrep- ancies. to enhance your Cannon’s appearance add a decorative 3 or 4 sided surround. every Cannon heater brings you the optional convenience of controlling your heater through a remote thermostat. -
Page 6: Fitzroy Inbuilt Power Flue Specifications
FIG 3 * For installation into a masonry/brick fireplace Rear wall 700 – 780 mm 690 mm 808 mm 50 mm 386 mm 50 mm fig 3 front View and side View 6 | Cannon Fitzroy Inbuilt Power Flue... -
Page 7: Regulatory Locator
5 For appliances not addressed above acceptance should be obtained from the technical regulator. THE POWER FLUE HEATER IS FAN ASSISTED. SEE COLUMN HIGHLIGHTED Special Note: This chart shall be read in-conjunction with the full Australian standards. fig 4 Cannon Fitzroy Inbuilt Power Flue | 7... -
Page 8: Power Flue Installation Instructions
Height 650 mm 630 mm the Powerflue heater is 6.0m. Width 780 mm 731 mm Depth 486mm or 586mm* *486mm min clearance for straight through flue. 586mm min clearance for flex flue pipe 8 | Cannon Fitzroy Inbuilt Power Flue... - Page 9 FLOOR 50 mm LEVEL 100 mm Corner wall application refer to mock fireplace installation for fig 11 corner wall application on page 24. air inlet 25min flue outlet Condensate fig 13 fig 12 Cannon Fitzroy Inbuilt Power Flue | 9...
- Page 10 17 EXTERNAL WALL TERMINAL COVER PLATE TERMINAL COVER PLATE PLACED TO HAVE TERMINAL ON AN INCLINE. FLUE TERMINAL WALL FIXING: USE SUITABLE FASTENERS FOR WALL CONSTRUCTION fig 19 fig 18 10 | Cannon Fitzroy Inbuilt Power Flue...
-
Page 11: Fascia Removal And Electrical Connection
Cannon Fitzroy Inbuilt Power Flue | 11... -
Page 12: Log Installation & Gas Connection
Do not seal with a silicone sealant as the heater must be easily removable. Sealing is important as it prevents any leakage of flue products into the room. test all connections for gas leaks. 12 | Cannon Fitzroy Inbuilt Power Flue... -
Page 13: Setting The Gas Pressure
Hold • Check that the gas pressure is correctly adjusted • Check that flue is operating correctly If the heater still does not operate to specification refer to the troubleshooting chart on page 19, or contact Sampford IXl in your state. adjust fig 33 Cannon Fitzroy Inbuilt Power Flue | 13... -
Page 14: Service Instructions
3. Disconnect the fan plug from the plug carrier. remove the two M5 wing nuts which locate the fan to the fan chamber underside. lower fan from male thread. gas and fan contoller Ignition Module gas valve fig 34 14 | Cannon Fitzroy Inbuilt Power Flue... - Page 15 2. Disconnect the plugs on box. 3. remove the screw retaining the bracket 4. replace the control box 5. Check and re-set gas pressures. To Replace Type “X”Cord Contact Sampford IXl service department. Cannon Fitzroy Inbuilt Power Flue | 15...
-
Page 16: Wiring Diagram
ROOM FAN - F3594 1.5 AMP[18] EARTH BLUE PRESSURE BLUE IGNITION MODULE SWITCH F3776 PRESSURE F3435 COMBUSTION SWITCH F3327 240 V MAINS PLUG ROOM AIR FAN POWERFLUE WIRING DIAGRAM F3834 A fig 37 16 | Cannon Fitzroy Inbuilt Power Flue... -
Page 17: Troubleshooting
One wire should be to C (Common) and the other should be to nO (normally Open). If it still doesn’t work after checking the above, change the pressure switch. Cannon Fitzroy Inbuilt Power Flue | 17... - Page 18 If there is no gas to the burner when this occurs check the solenoid coils for continuity. • C heck that the gas pressure is present at the test point when the spark is being generated. • Check that there is gas to the inlet of the gas control. Fuse blowing. • I f the fuse continues to blow check the solenoid coils for a signs of them being shorted. • Check the fan and wiring for short circuit. 18 | Cannon Fitzroy Inbuilt Power Flue...
-
Page 19: Notes
Cannon Fitzroy Inbuilt Power Flue | 19... - Page 20 For service to this appliance or spare parts Gmk 10025 contact the CANNON distributor: Gmk 10030 AS4553:2008 Sampford IXL – Spare Parts Phone: 1300 727 421 Part number: Fax: 1300 727 425 F3840_A Email: service@sampfordixl.com.au 20 | Cannon Fitzroy Inbuilt Power Flue...
Need help?
Do you have a question about the Fitzroy Inbuilt Power Flue and is the answer not in the manual?
Questions and answers