Table of Contents
Advertisement
6 – Locate the controller's remote RJ-11 jack and insert
the modular connector. See Figure 2.
T T h h e e c c o o n n t t r r o o l l l l e e r r i i l l l l u u s s t t r r a a t t e e d d i i n n F F i i g g u u r r e e 2 2 i i s s s s h h o o w w n n
f f o o r r r r e e f f e e r r e e n n c c e e o o n n l l y y . . R R e e f f e e r r t t o o t t h h e e c c o o n n t t r r o o l l l l e e r r u u s s e e r r ' ' s s
g g u u i i d d e e f f o o r r s s p p e e c c i i f f i i c c i i n n s s t t a a l l l l a a t t i i o o n n i i n n f f o o r r m m a a t t i i o o n n . .
7 – Locate the controller's 24 VAC connection terminals
and attach the receiver power wires.
wire to either terminal.
8 – Apply power to the controller. The receiver Activity
monitor should begin flashing Green. If the Activity
monitor does not illuminate, confirm the receiver is
properly installed and plug assembly is wired correctly.
O O u u t t d d o o o o r r I I n n s s t t a a l l l l a a t t i i o o n n
C C A A U U T T I I O O N N : : T T h h e e r r e e c c e e i i v v e e r r p p l l u u g g i i s s w w e e a a t t h h e e r r r r e e s s i i s s t t a a n n t t o o n n l l y y
w w h h e e n n i i n n s s t t a a l l l l e e d d i i n n P P V V C C c c o o n n d d u u i i t t a a n n d d t t h h e e p p l l u u g g c c o o v v e e r r i i s s i i n n
p p l l a a c c e e . . T T h h e e r r e e c c e e i i v v e e r r u u n n i i t t i i s s n n o o t t w w e e a a t t h h e e r r r r e e s s i i s s t t a a n n t t a a n n d d
s s h h o o u u l l d d o o n n l l y y b b e e i i n n s s t t a a l l l l e e d d o o u u t t d d o o o o r r s s f f o o r r t t e e m m p p o o r r a a r r y y u u s s e e . . D D o o
n n o o t t a a l l l l o o w w i i r r r r i i g g a a t t i i o o n n s s p p r r a a y y t t o o c c o o n n t t a a c c t t t t h h e e r r e e c c e e i i v v e e r r d d u u r r i i n n g g
s s p p r r i i n n k k l l e e r r o o p p e e r r a a t t i i o o n n . .
1 – At the selected installation site, bore a
the wall for
2 – Install a length of PVC pipe through the wall, leaving
about 1" of pipe on both sides.
3 – Inside, install a 90° elbow and a 3" section of pipe.
Use a conduit clamp to secure the pipe assembly to
the wall. See Figure 3.
4 – Remove the mounting bracket from the plug assembly.
5 – Insert the receiver plug wiring through the threaded
end of a
plug into the PVC fitting and tighten by hand.
6 – Route the wiring through the conduit. Install the
plug/fitting assembly to the pipe, orienting the plug
alignment hole pointing straight down.
7 – Connect the receiver plug wiring as described above.
8 8
⁄
" PVC pipe access.
1
2
1
⁄
" thread/slip PVC fitting. Thread the receiver
2
T T M M R R - - 1 1
Connect either
⁄
" hole through
3
4
R R e e c c e e i i v v e e r r I I n n s s t t a a l l l l a a t t i i o o n n
Advertisement
Table of Contents
