Available Signals - JVC DT-V20L3DY Instructions Manual

7 Available signals

The following signals are available for this monitor.
Video signals
Signal format
shown in the
No. Signal name
status display
(INPUT1,
(☞ page 7)
INPUT2)
1 NTSC NTSC
2 PAL PAL
3 B/W50 B/W50
4 B/W60 B/W60
5 480/60i 480/60i
6 480/59.94i 480/59.94i
7 576/50i 576/50i
8 480/60p 480/60p
9 480/59.94p 480/59.94p
10 576/50p 576/50p
11 640*480/60p 640*480/60p
12 640*480/59.94p 640*480/59.94p
13 720/60p 720/60p
14 720/59.94p 720/59.94p
15 720/50p 720/50p
16 720/30p 720/30p
17 720/29.97p 720/29.97p
18 720/25p 720/25p
19 720/24p 720/24p
20 720/23.98p 720/23.98p
21 1080/60i 1080/60i
22 1080/59.94i 1080/59.94i
23 1035/60i 1035/60i
24 1035/59.94i 1035/59.94i
25 1080/50i 1080/50i
26 1080/60p 1080/60p
27 1080/59.94p 1080/59.94p
28 1080/50p 1080/50p
29 1080/30p 1080/30p
30 1080/29.97p 1080/29.97p
31 1080/25p 1080/25p
32 1080/24p 1080/24p
33 1080/23.98p 1080/23.98p
34 1080/30psF 1080/60i
35 1080/29.97psF 1080/59.94i
36 1080/24psF 1080/24psf
37 1080/23.98psF 1080/23.98psf
√: Acceptable
—: Not acceptable
* 1 Analog component/analog RGB signals are compatible with G on sync signal, Y on sync signals, and composite sync
signals (C ). The separate sync signal (HS/VS) is not compatible.
S
* 2 Compatible with EMBEDDED AUDIO signals
* 3 The signal is recognized as 1080/60i, 1080/59.94i.
Input terminal
COMPO./RGB
VIDEO E. AUDIO HD/
(Analog
SD SDI
component/
2
(IN 1, IN 2)*
1
Analog RGB)*
√ — —
√ — —
√ — —
√ — —
— √ √
√ √
—
— √ √
— √ —
— √ —
— √ —
— — —
— — —
— √ √
— √ √
— √ √
√ √
—
— √ √
— √ √
— √ √
— √ √
— √ √
— √ √
— √* 3 √
3 √
— √*
— √ √
— — —
— — —
— — —
√ √
—
— √ √
— √ √
— √ √
— √ √
3 3
— √* √*
— √* 3 √* 3
— √ √
— √ √
Computer signals (preset)
DVI-D (HDCP) terminals
No. Signal name
1 VGA60
DVI-D (HDCP) 2 WVGA60
(Digital component/
3 SVGA60
digital RGB)
4 XGA60
—
5 WXGA (1280)
—
6 WXGA+60
—
7 SXGA60
—
8 WSXGA+60
√
4
9 UXGA60*
√
10 WUXGA60* 4
√
11 720/60p
√
12 1080/60p* 4
√
13 720/50p
√
4
14 1080/50p*
√
* 4 For DT-V20L3DY: When No. 9, 10, 12 or 14 signals come in, thin lines will become obscured because their signal
√
resolution is higher than the screen resolution.
√
• Non-preset signals may not be displayed normally even if their frequency is within the acceptable range (☞
√
"Horizontal/vertical frequency (computer signal)" on page 21).
√
• When a preset signal comes in, the signal format is shown on the status display. For other signals, the
— resolution is shown.
—
—
Specification of the DVI-D (HDCP) terminal
—
Connect it to the DVI-D output terminal on a personal computer.
—
√
Pin No. Input signal
√
1
√* 3
2
3
√*
3
√
4
√
5
√
6
√
7
√
8
√
√
√
√
—
—
—
—
Resolution
Horizontal Vertical Horizontal (kHz)
640 480
852 480
800 600
1024 768
1280 768
1440 900
1280 1024
1680 1050
1600 1200
1920 1200
1280 720
1920 1080
1280 720
1920 1080
Pin No. Input signal
T.M.D.S Data 2– 9 T.M.D.S Data 1–
T.M.D.S Data 2+ 10 T.M.D.S Data 1+
T.M.D.S Data 2 shield 11 T.M.D.S Data 1 shield
NC 12 NC
NC 13 NC
DDC Clock 14 +5 V Power
DDC Data 15 GND
NC 16 Hot Plug Detect
Frequency
Scan system
Vertical (Hz)
31.5 59.9 Non-interlace
31.5 59.9 Non-interlace
37.9 60.3 Non-interlace
48.4 60.0 Non-interlace
47.8 60.0 Non-interlace
55.9 60.0 Non-interlace
64.0 60.0 Non-interlace
65.2 60.0 Non-interlace
75.0 60.0 Non-interlace
74.0 60.0 Non-interlace
45.0 60.0 Non-interlace
67.5 60.0 Non-interlace
37.5 50.0 Non-interlace
56.25 50.0 Non-interlace
Pin No. Input signal
17 T.M.D.S Data 0–
18 T.M.D.S Data 0+
19 T.M.D.S Data 0 shield
20 NC
21 NC
22 T.M.D.S Clock shield
23 T.M.D.S Clock+
24 T.M.D.S Clock–
9