Table of Contents
Advertisement
• When using the optional stay
!"#
•
Dashboard
Removing the unit
• Before removing the unit, release the rear section.
1
Remove the control panel.
2
Remove the trim plate.
3
Insert the 2 handles into the slots, as shown. Then, while gently
pulling the handles away from each other, slide out the unit.
(Be sure to keep the handles after installing it.)
1
Parts list for installation and connection
The following parts are provided with this unit.
After checking them, please set them correctly.
Hard case/Control panel
!"#$
Power cord
!"#$%&
ENGLISH
ELECTRICAL CONNECTIONS
To prevent short circuits, we recommend that you disconnect the
battery's negative terminal and make all electrical connections
before installing the unit. If you are not sure how to install this unit
correctly, have it installed by a qualified technician.
Note:
This unit is designed to operate only on 12 volts DC, NEGATIVE
ground electrical systems. If your vehicle does not have this
system, a voltage inverter is required, which can be purchased at
JVC car audio dealers.
• Replace the fuse with one of the specified rating. If the fuse
blows frequently, consult your JVC car audio dealer.
• If noise is a problem...
This unit incorporates a noise filter in the power circuit. However,
with some vehicles, clicking or other unwanted noise may occur.
If this happens, connect the unit's rear ground terminal (see
connection diagram) to the car's chassis using shorter and thicker
cords, such as copper braiding or gauge wire. If noise still persists,
consult your JVC car audio dealer.
• Maximum input of the speakers should be more than 45 watts at
the rear and 45 watts at the front, with an impedance of 4 to 8
ohms.
• Be sure to ground this unit to the car's chassis.
• The heat sink becomes very hot after use. Be careful not to
touch it when removing this unit.
Heat sink
•
Fire wall
Stay (option)
Washer
Lock nut
!
Screw (option)
Mounting bolt
!
Sleeve
!
!
!"#$%&!"'()*+,-.(/012
•
1
!"#$
2
!"#
3
!"#$%&'()*+,-."/01234$5
!"#$%&'()
!"#$%&'()*+,-.
2
!"#$%&'(
!"#$%&'()
!"#$%&'()*
Sleeve
!
Washer (ø5)
Handles
!"
(ø5)
!
!"#$%&'()*+,#-./0123#4567/
!"#$%&'()*$+,)-./012345678
!"#$
!"#$%12V
!"#$%&' ( )*+,$-./JVC
!"
!"#$%&'()*
•
JVC
!"#$
•
!"#$%&'()*+,-./01 2345617
!"#$%&'()*+,-./012345678
!"#$%&'()*+&,-./0'123
!"#$%&'(
!"#$%&'
!"#$%&'()*%+45
•
!"#$ 4 – 8
45
!"#$%&'()
•
!"#$%&'(%)*+#,-.
•
!"
• When installing the unit without using the sleeve
!"#$%&'($
•
In a Toyota for example, first remove the car radio and install the unit in its place.
!"TOYOTA
Flat type screws (M5 x 6 mm)*
!" (M5 x 6 mm)*
!"
*
Bracket*
*
!"
Note: When installing the unit on the mounting bracket, make sure to use the 6 mm-long screws. If
longer screws are used, they could damage the unit.
!"#$%&'()*+ 6m
*+
Trim plate
Lock nut (M5)
! (M5)
M5
!"#$%&'
!"#$%&
!+,-
!./0123
!"#$%&'
!"#$%&'()*+ JVC
!"#$%&'()
/#01234
!"#$%&'
()*+,-./*0123'4567
M5
*
Pocket
Bracket*
*
*
!"#$%&'
m™¯
3
Handle
Remote controller
!
Mounting bolt (M5 x 20 mm)
! (M5 x 20 mm)
M5
!"#
DC
JVC
!
•
* Not included with this unit.
!"#$
*
*
Flat type screws (M5 x 6 mm)*
!
(M5 x 6 mm)*
*
M5
!()*+,-"
•
!"
Battery
CR2025
Rubber cushion
!"
•
JVC
•
JVC
•
•
•
Advertisement
Table of Contents
