KD-SX870 KD-SX770 3 7 63 1515 0 Safety precaution ! CAUTION Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system.
KD-SX870 KD-SX770 Preventing static electricity 3 7 63 1515 0 Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.
KD-SX870 KD-SX770 3 7 63 1515 0 Location of main parts Control unit Display Front PCB Changer control Antenna Main unit connector jack Main board 16 pin connector RCA jack L 13942296513 Power IC Tuner pack Main board assembly...
KD-SX870 KD-SX770 3 7 63 1515 0 Disassembly method Removing the front chassis (See Fig.1) 1. Remove two screws A and insert a screwdriver to the joints a on the side of the front chassis and two joints b on the right side, then detach the front chassis toward the front side.
Page 6
KD-SX870 KD-SX770 3 7 63 1515 0 Main amplifier board CN501 Removing the main amplifier board assembly (See Fig.4 and 5) Remove the front chassis. Remove the bottom cover. Remove the two screws C attaching the main amplifier board assembly on the bottom of the body.
Page 7
KD-SX870 KD-SX770 3 7 63 1515 0 Damper bracket Removing the CD mechanism control CD mechanism ass’y board(See Fig.1 and 2) Unsolder the part f and g on the CD mechanism control board. Remove the stator fixing the CD mechanism control board and the damper bracket (To remove the stator smoothly, pick up the center part).
Page 8
KD-SX870 KD-SX770 3 7 63 1515 0 Removing the loading motor Loading motor (See Fig.3 to 5) Prior to performing the following procedure, remove the CD mechanism control board. Belt Remove the two springs k attaching the CD mechanism ass’y and the front bracket.
Page 9
KD-SX870 KD-SX770 3 7 63 1515 0 Removing the feed motor ass’y Part n FD screw (See Fig.10) Feed motor ass’y Prior to performing the following procedure, remove the CD mechanism control board, the front bracket Part O (loading motor) and the CD mechanism ass’y.
Page 10
4.Stereo modulator 5.Electric voltmeter 6.Digital tester Frequency Band 7.Tracking offset meter 1 – 3 87.5MHz – 107.9MHz 8.Test Disc JVC : CTS-1000 9.Extension cable for check 530kHz – 1710kHz EXTGS004-26P Dummy load Exclusive dummy load should be used for AM,and FM.
KD-SX870 KD-SX770 3 7 63 1515 0 Flow of Functional Operation Unit TOC Read Power ON Set Function CD When the laser diode correctly When the pickup correctly moves emits to the inner area of the disc Microprocessor $82 $81...
Page 12
KD-SX870 KD-SX770 3 7 63 1515 0 Feed section Is the voltage output at Is the wiring for IC541 Is 5V present at IC501 IC541 pin "53" 5V or 0V? (90)~(100) correct? pin "20"? Check CD 9V Check the vicinity of and 5V.
KD-SX870 KD-SX770 3 7 63 1515 0 Maintenance of laser pickup (1) Cleaning the pick up lens Before you replace the pick up,please try to clean the lens with a alcohol soaked cotton swab. (2) Life of the laser diode When the life of the laser diode has expired, the following symptoms will appear.
Page 18
KD-SX870 KD-SX770 3 7 63 1515 0 LA4743K(IC351):Power AMP 1.Block diagram 2200 F 0.022 F Vcc 1/2 Vcc 3/4 IN 1 OUT 1+ 0.22 F OUT 1- PWR GND1 Protective circuit OUT 2+ IN 2 OUT 2- 0.22 F...
Page 19
KD-SX870 KD-SX770 3 7 63 1515 0 2.Terminal layout 3.Pin function Pin No. Symbol Function Header of IC Power GND OUTRR- Outpur(-) for front Rch STBY Stand by input OUTRR+ Output (+) for front Rch VCC1/2 Power input OUTRF-...
Page 20
KD-SX870 KD-SX770 3 7 63 1515 0 LA6567H-X(IC581):CD DRIVE 1.Pin layout & blockdiagram CH 3,4,5 Thermal shutdown VCC2 Power supply VO5- VO5+ S-GND VO4+ VCONT VO4- VIN4 VO3+ VIN4G Signal system power supply VO3- VCC-S L 13942296513 VC2+ VREF-IN...
Page 21
KD-SX870 KD-SX770 3 7 63 1515 0 2. Pin function LA6567H-X(2/2) Pin no. Symbol Function VCC2 CH3,4,5 Power supply( It is short with VCC1,VCC-S) VO5- Loading output(-) VO5+ Loading terminal (+) VO4+ CH4 Output terminal(+) VO4- CH4 Output terminal(-)
Page 22
KD-SX870 KD-SX770 3 7 63 1515 0 LC75873NW (IC601) : LCD Driver 1.Terminal layout 2.Pin function Symbol Function Pin No. 1 58 SEG3 SEG60 Segment outputs 59 66 Non connection 67 69 COM1 COM3 Common driver outputs L 13942296513...
Page 24
KD-SX870 KD-SX770 3 7 63 1515 0 3.Pin function UPD178078GF(1/2) FUNCTION Symbol Non connection JBUS-INT JVC BUS COMMUNICATION LINE JBUS-SI JVC BUS COMMUNICATION LINE JBUS-SO JVC BUS COMMUNICATION LINE JBUS-SCK JVC BUS COMMUNICATION LINE Non connection Non connection Non connection...
Page 25
KD-SX870 KD-SX770 3 7 63 1515 0 UPD178078GF(2/2) FUNCTION Symbol CD MECHA SW REMOCON REMOCON INPUT VTR-LOGIC Non connection VTR-CONT Non connection POWER POWER CONT. CD-ON CD POWER CONT. MUTE MUTE CONT Non connection BUZZER BEEP FOR SW OPERATION...
Page 26
KD-SX870 KD-SX770 3 7 63 1515 0 NJM4565M-WE (IC111) : Ope. amp A OUTPUT A INPUT B OUTPUT A INPUT B INPUT B INPUT L 13942296513 RPM6938-SV4(IC602) : Remote Sensor Comp Rout Detector conversion trimming circuit magnetic shield u163 1-26 http://www.xiaoyu163.com...
Page 28
KD-SX870 2.Pin function KD-SX770 PIN No. SYMBOL FUNCTIONAL DESCRIPTION REMARKS 3 7 63 1515 0 Test mode terminal.Normally, Keep at open. With pull-up resistor. TEST0 Playback speed mode fllag output terminal. UHSO PLAYBACK SPEED Nomal 2 times 4 times UHSO Subcode Q data emphasis flag output terminal.Emphasis ON at "H"...
Page 29
KD-SX870 KD-SX770 3 7 63 1515 0 2.Pin Function TC9462F(2/2) Remarks Pin No. Symbol I/O Function Function Sub-beam adder signal input terminal SBAD Analog input. Test input terminal Normally, keep at "vref" level TSIN Analog input. Tracking error signal input terminal. Take in at tracking servo ON.
Page 30
KD-SX870 KD-SX770 3 7 63 1515 0 HA13164A (IC961) : Regulator 1. Pin layout 2. Block diagram Surge Protector BATT.DET ANTOUT EXTOUT BIAS COMP ANT CTRL VDDOUT CTRL SW5V CDOUT IL MOUT AUDIOOUT L 13942296513 ILM AJ HA13164 (IC901)
Page 32
KD-SX870 KD-SX770 3 7 63 1515 0 L 13942296513 u163 VICTOR COMPANY OF JAPAN, LIMITED MOBILE ELECTRONICS DIVISION PERSONAL & MOBILE NETWORK BUSINESS UNIT 10-1,1chome,Ohwatari-machi,Maebashi-city,Japan Printed in Japan (No.49595) 200102(M) http://www.xiaoyu163.com...
Page 33
Block Diagram KD-SX870 3 7 6 3 1 5 1 5 0 KD-SX770 CD Mechanism ENC 1,2 SYSTEM VOLUME JOG CD PICKUP UNIT MECHA. SWITCH CONTROLLER EN601 IC701 SW1~4 uPD178078GF-543 REMOCON SPINDLE/FEED REMOTE CONTROL VOL CL MOTOR RECEIVER VOL DA...
Page 34
KD-SX870 KD-SX770 3 7 63 1515 0 < M E M O > L 13942296513 u163...
Page 35
KD-SX870 Standard schematic diagrams KD-SX770 3 7 6 3 1 5 1 5 0 Receiver & power amplifier circuit 1 3 9 4 2 2 9 6 5 1 3 w w w u 1 6 3 CD/MAIN SIGNAL TUNER SIGNAL http://www.xiaoyu163.com...
Page 36
KD-SX870 KD-SX870 KD-SX770 KD-SX770 3 7 6 3 1 5 1 5 0 Main circuit 1 3 9 4 2 2 9 6 5 1 3 w w w u 1 6 3 CD/MAIN SIGNAL...
Page 37
KD-SX870 KD-SX770 3 7 6 3 1 5 1 5 0 LCD driver & Operation switch circuit 1 3 9 4 2 2 9 6 5 1 3 w w w u 1 6 3 http://www.xiaoyu163.com...
KD-SX870 KD-SX770 3 7 63 1515 0 PARTS LIST [ KD-SX870 ] [ KD-SX770 ] * All printed circuit boards and its assemblies are not available as service parts. Area suffix J -------------- Northern America L 13942296513 - Contents -...
Page 41
KD-SX870 KD-SX770 3 7 63 1515 0 Exploded view of general assembly and parts list Block No. L 13942296513 u163 http://www.xiaoyu163.com...
Page 42
MINI SCREW 1 LOCK LEVER(O.L.) FSKW4013-002 T.SPRING 1 FOR OPEN LEVER BLIND VYTA526-002 GE10005-001A FRONT PANEL GE30113-006A FINDER ASSY 1 KD-SX870 GE30113-007A FINDER ASSY 1 KD-SX770 FSJK4009-001 REMOTE LENS 1 FOR REMOTE CON. GE20104-001B PRESET BUTTON 1 1-6 (2 COLOUR) GE30105-002B...
Page 43
RUBBER CONNECTOR QNZ0450-001 RUBBER CONNECTOR GE30114-001A LCD CASE FSJK3028-001 LCD LENS FSYH4061-001 LIGHTNG SHEET FSKS3013-001 LENS CASE GE30153-002A NAME PLATE 1 KD-SX870 GE30152-001A NAME PLATE 1 KD-SX770 VMA4652-001SS EARTH PLATE FSKL4024-001 IC BRACKET GE40103-001A REG BRACKET GE40104-002B HEAT SINK REAR BRACKET...
Page 44
KD-SX870 KD-SX770 3 7 63 1515 0 CD mechanism assembly and parts list Block No. Grease TN-CCD1001Z-136J G-31SA G-31SA(Bottom side) RX-405 L 13942296513 u163 106 29 http://www.xiaoyu163.com...
Page 45
KD-SX870 KD-SX770 3 7 63 1515 0 Parts list (CD mechanism) Block No. M2MM Item Parts number Parts name Q'ty Description Area 30310101T FRAME 30310103T DANPER PIN 30310107T UPPER PLATE 30310108T SEL STOP PLATE 30310142T SEL ARM (L)L SEL ARM (R)L...
Page 46
KD-SX870 KD-SX770 3 7 63 1515 0 Parts list (CD mechanism) Block No. M2MM Item Parts number Parts name Q'ty Description Area 64180403T DET SWITCH 2 ESE22MH3 68150232T CONNECTOR 1 TKC-W26X-C1 30311105T SOPPORT PLATE 30311138T GR MT BLK(N) 30311109T...
Page 47
KD-SX870 KD-SX770 3 7 63 1515 0 Electrical parts list (Main board) Block No. 01 Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area BZ871 QAN0009-001Z BUZZER C 356 NCB31HK-223X C CAPACITOR NCB31EK-473X C CAPACITOR...
Page 48
KD-SX870 KD-SX770 3 7 63 1515 0 Electrical parts list (Main board) Block No. 01 Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area C 544 QERF0JM-107Z E CAPACITOR 100MF 20% 6.3V C 994...
Page 49
KD-SX870 KD-SX770 3 7 63 1515 0 Electrical parts list (Main board) Block No. 01 Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area UN2211-X TRANSISTOR R 331 NRSA63J-103X MG RESISTOR KD-SX870 2SB709A/R/-X TRANSISTOR...
Page 50
KD-SX870 KD-SX770 3 7 63 1515 0 Electrical parts list (Main board) Block No. 01 Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area R 509 NRSA63J-333X MG RESISTOR R 735 NRSA63J-103X MG RESISTOR...
Page 51
KD-SX870 KD-SX770 3 7 63 1515 0 Electrical parts list (Switch board) Block No. 02 Item Parts number Parts name Remarks Area Item Parts number Parts name Remarks Area C 601 NBE20JM-475X E CAPACITOR R 609 NRSA63J-182X MG RESISTOR...
Page 52
KD-SX870 KD-SX770 3 7 63 1515 0 < M E M O > L 13942296513 u163 3-13 http://www.xiaoyu163.com...
Page 53
KD-SX870 KD-SX770 3 7 63 1515 0 Packing materials and accessories parts list Block No. Block No. L 13942296513 KIT:A8 u163 3-14 http://www.xiaoyu163.com...
Page 54
POLY BAG 1 KIT QPA01003003 POLY BAG 1 HARD CASE FSYH4036-068 SHEET QPC03004315P POLY BAG 1 SET GE30123-018A CARTON 1 KD-SX870 GE30121-017A CARTON 1 KD-SX770 GE10008-001A ESP CUSHION Parts list (Accessories) Block No. M4MM Item Description Parts number Parts name...