Download Print this page

JVC CD Receiver KD-G417 Installation And Connection Manual

Jvc cd player installation manual
Hide thumbs Also See for CD Receiver KD-G417:

Advertisement

Quick Links

KD-G417/KD-G317
Installation/Connection Manual
GET0261-002B
[EE]
ENGLISH
This receiver is designed to operate on 12 V DC, NEGATIVE ground electrical systems. If
your vehicle does not have this system, a voltage inverter is required, which can be purchased
at JVC IN-CAR ENTERTAINMENT dealers.
Parts list for installation and connection
The following parts are provided for this receiver.
After checking them, please set them correctly.
A / B
Hard case/Control panel
F
G
Washer (ø5)
Lock nut (M5)
INSTALLATION (IN-DASH MOUNTING)
The following illustration shows a typical installation. If you have any questions or require
information regarding installation kits, consult your JVC IN-CAR ENTERTAINMENT dealer or a
company supplying kits.
• If you are not sure how to install this receiver correctly, have it installed by a qualified technician.
Removing the receiver /
Before removing the receiver, release the rear section.
Insert the two handles, then
pull them as illustrated so
that the receiver can be
removed.

TROUBLESHOOTING

• The fuse blows.
* Are the red and black leads connected correctly?
• Power cannot be turned on.
* Is the yellow lead connected?
• No sound from the speakers.
* Is the speaker output lead short-circuited?
• Sound is distorted.
* Is the speaker output lead grounded?
* Are the "–" terminals of L and R speakers grounded in common?
• Noise interfere with sounds.
* Is the rear ground terminal connected to the car's chassis using shorter and thicker cords?
• Receiver becomes hot.
* Is the speaker output lead grounded?
* Are the "–" terminals of L and R speakers grounded in common?
• This receiver does not work at all.
* Have you reset your receiver?
C
Sleeve
H
Mounting bolt (M5 x 20 mm)
*
1
When you stand the receiver, be
careful not to damage the fuse on
the rear.
*
1
When using the optional stay /
Fire wall
Dashboard
Install the receiver at an
angle of less than 30˚.
D
Trim plate
I
Rubber cushion
Do the required electrical connections.
When installing the receiver without using the sleeve /
In a Toyota for example, first remove the car radio and install the receiver in
Stay (option)
its place.
Flat type screws
(M5 x 8 mm)*
*
Bracket*
Screw (option)
Pocket
Note
: When installing the receiver on the mounting bracket,
make sure to use the 8 mm-long screws. If longer screws
are used, they could damage the receiver.
*
*
*
*
*
*
*
*
*
1
0405DTSMDTJEIN
EN, RU
E
Power cord
J
Handles
Bend the appropriate tabs to hold
the sleeve firmly in place.
* Not included for this receiver.
*
*
Flat type screws
(M5 x 8 mm)*
Bracket*
*
*

Advertisement

loading

Summary of Contents for JVC CD Receiver KD-G417

  • Page 1: Troubleshooting

    INSTALLATION (IN-DASH MOUNTING) The following illustration shows a typical installation. If you have any questions or require information regarding installation kits, consult your JVC IN-CAR ENTERTAINMENT dealer or a company supplying kits. • If you are not sure how to install this receiver correctly, have it installed by a qualified technician.
  • Page 2: Electrical Connections

    • Be sure to ground this receiver to the car’s chassis again after installation. Notes: • Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC IN-CAR ENTERTAINMENT dealer. • It is recommended to connect to the speakers with maximum power of more than 50 W (both at the rear and at the front, with an impedance of 4 Ω...

This manual is also suitable for:

Kd-g317