Burner Igniters; Stainless Steel Surfaces; Burner Bases; Burner Rings - Dacor Epicure Use & Care Manual

4. Use caution when cooking to avoid spills
as much as possible. Porcelain is acid-
resistant but not acid-proof, so some foods
can cause permanent damage if allowed to
remain on porcelain surfaces.
Daily cleaning of the grates and burner caps is
best accomplished with a soft cloth or sponge
dampened in a solution of warm water and hand
dishwashing liquid. Grates and burner caps
should not be cleaned in the dishwasher.
Stubborn stains may be removed by applying
full-strength sprays such as Simple Green, Ajax
All-Purpose Cleaner, Formula 409, or Scotch
Guard. Metal polishing compounds such as
Luneta or Flitz may also be used. (If you are
unable to locate these cleaning compounds,
please phone the DACOR Customer Service
Department for a referral.)
Mildly abrasive cleaners or applicators, such
as S.O.S. Pads, soap-filled steel wool pads,
Soft Scrub, or Bon-Ami may be used with
extreme care on occasion to remove the most
serious stains. Exercise caution – extensive
use of abrasives will eventually damage the
porcelain enamel surface.

Stainless Steel Surfaces

Clean these surfaces with the provided Elco
Stainless Steel Cleaner. Rinse and dry with a
soft lint-free cloth.
ImpORTANT:
If commercially available stainless steel
cleaners are used, it is important to read the
labels for chlorine compounds. Chlorine is a
corrosive substance. If these compounds are
present, rinse thoroughly and dry with a soft
lint-free cloth.
Always wipe stainless steel surfaces with the
grain.
porcelain Surfaces
The work spill zone is finished in black porcelain
enamel. Clean this surface with a solution of
mild detergent and hot water. Rinse with a soft
cloth. Do not use abrasives or commercial oven
cleaners.
Stubborn stains may be removed by applying
full-strength sprays such as Simple Green, Ajax
All-Purpose Cleaner, Formula 409, or Scotch
Guard.
ImpORTANT:
1. Never use the cooktop surface as a
cutting board.
2. Do not use abrasive cleaners or
applicators on the cooktop.
3. Do not try to remove heavy spills with
a sharp object such as a knife or metal
spatula. Sharp objects may scratch the
cooktop.
4. A small amount of baby oil may be
applied to stainless steel tops to restore
the lustre.
Knobs and Knob Bezels
The control knobs provided with this cooktop are
designed for ease of use and longevity. The "D"
shaped design of the knob shaft ensures proper
orientation when re-installing the knob. Knobs
have a clearly defined chamfer to make setting
the flame height an easy task.
ImpORTANT:
Never block the holes in the control panel
behind the knobs, because this will impair
the flow of combustion air and adversely
affect burner operation, possibly creating a
hazardous condition.
The knobs are made of a composite plastic.
These components should be washed regularly
in warm, soapy water. Hand dishwashing
liquid is excellent for this task. Knobs should
be removed by gently pulling them straight out
and off of the valve shafts. The knob bezels
should be cleaned in place. Use caution to avoid
introduction of moisture into the control panel
behind the bezels. To replace knobs, align the
"D-shaped" opening at the bottom of the knob
with the "D-shaped" valve shaft, then carefully
press the knob onto the valve.
ImpORTANT:
1. Turn the knobs to the "Off" position
prior to removing them from the valve
stems.
2. The cooktop should never be operated
without the knobs in place.
3. Do not soak the knobs in water or place
them in the dishwasher.
4. Do not expose the knobs to direct
flame, hot utensils, or other sources of
heat.
5. Do not use abrasive or corrosive
cleaners or applicators, as these could
cause permanent damage.

Burner Bases

The burner base, which is permanently attached
to the cooktop, is made of aluminum. The
base should be wiped clean using a soft cloth
or sponge that has been lightly dampened
with warm water and hand dishwashing liquid.
Thoroughly clean and dry the igniters to prevent
constant sparking of the reignition system. Refer
to the Burner Igniters for cleaning tips.

Burner Rings

The brass burner rings spread the flame evenly
around the burner perimeters. The burner rings
must seat properly in the burner bases to enable
proper cooktop operation. To ensure proper
seating, five positioning tabs have been placed
on the bottom of each burner ring to slide into
corresponding notches in the fixed burner base.
To remove the burner ring, first lift off the
porcelain burner cap. The burner ring may
then be removed from the burner base. Soak
the burner ring in a warm solution of hand
dishwashing liquid and water, then rinse well
with clean water. Dry the burner thoroughly
before placing it back on the burner base.
4
Stubborn stains may be removed by applying
a metal polishing compound such as Luneta
or Flitz. (If you are unable to locate this type of
polishing compound, please phone the DACOR
Customer Service Department for a referral.)

Burner Igniters

Under certain cooking or cleaning conditions,
your cooktop igniters may become coated
with or corroded by food deposits, splattered
grease or cleaning agents. This condition can
cause erratic or continuous sparking. Keeping
the igniters clean and dry will help to reduce
this problem. To avoid unnecessary and costly
service calls, the homeowner should perform
periodic cleaning of the igniters. An Igniter
Cleaning Brush is enclosed for your use in
cleaning the cooktop igniters.
To clean the igniters:
1. Be sure burners are cool to the touch.
Remove the grate, burner cap and burner
rings.
2. Brush completely around the igniter,
including over and under the edge of
the metal cap and base. Use care while
cleaning here. The igniter is porcelain and
can be fragile.
3. DO NOT USE WATER when cleaning the
igniters. If a liquid must be used to clean
the igniter effectively, use only a small
amount of rubbing alcohol.
4. After cleaning, reinstall the burner ring,
burner cap and grate. Make sure the brass
burner ring is properly seated into the
burner base.
5. Test the burners. If erratic clicking is still
present, make sure the igniter is completely
dry. If the unit still exhibits problems after
drying, call your local DACOR Authorized
Servicer.
Brass, Chrome & Copper Surfaces
Clean these surfaces with a solution of mild
detergent and warm water. Rinse, dry and polish
with a soft, lint-free cloth.
ImpORTANT:
If a commercially available polish is used,
it is important to read the label for chlorine
compounds. Chlorine is a corrosive
substance and is not recommended for
use with brass or chrome finishes. If these
compounds are present, rinse the surface
thoroughly and dry with a soft, lint-free cloth.
Follow manufacturer's instructions for
application of polish.