JVC KV-MR9000 Instructions Manual page 58

ENGLISH
! /
Typical Connections /
Before connecting: Check the wiring in the
vehicle carefully. Incorrect connection may
cause serious damage to this unit.
The leads of the power cord and the ceiling light
cord and those of the connector from the car
body may be different in color.
7 Power supply connection
1
Connect the colored leads of the power cord
in the following sequence.
1
2
Black: ground
3
Yellow: to car battery (constant 12 V)
4
Red: to an accessory terminal
Blue: to remote control lead of the external
component (such as KS-IF200).
2
Finally connect the wiring harness to the unit.
1
2
Black/ / /
1
Yellow*
1
*
1
*
*
Red
5 A
Blue / =/
/
7 Ceiling light wire connection
1
Connect the colored leads of the ceiling light
cord in the following sequence.
1
2
Black: ground (GND)
Yellow: to car battery (constant 12 V)
3
(BATTERY B+)
4
Red: to an accessory terminal (ACC)
Grey: to the door sensor (DOOR SW)
Black/ / /
1
Yellow*
1
*
1
*
*
Red
Grey / =/
/
Connecting the leads /
Twist the core wires when connecting.
!"#$%&'
/
!" !"#$%&'()*+&'
!"#$%&'()
!"#$% "#&''( )*+,-
!"
7 !
1
!"#$%&'()*+,-.
1
!"
2
!"#$%&'() 12 V
3
!"#$%&'
4
!"#$%&'()*+,- KS-
IF200
2
!"#$%&'(
* 1 : Before checking the operation of this unit prior to installation, this lead must be connected, otherwise power cannot
be turned on.
!"#$%&'()*+,-./012345637.89:;<=>?@
* 1 :
1
* :
To metallic body or chassis of the car
!"#$%&'
1
To a live terminal in the fuse block connecting to the car battery (bypassing the ignition switch)
!"#$%& '()*+,-'./0'1230456789:;
2
5 A fuse
5 A
To an accessory terminal in the fuse block
!"#$%&'()*
3
1 A fuse
1 A
To remote lead of the external component (such as KS-IF200)
!"#$ KS-IF200
1 A
4
KS-IF200
7 !"#$
1
!"#$%&'()*+,-.
1
!"#GND
2
!"#$%&'() 12 V
3
BATTERY B+
4 !"#$%&'(ACC
!"#$%&'DOOR SW
* 3 : Cover the joined connectors with vinyl tape to prevent unexpected disconnection.
3
* * 3 :
* 3 :
To metallic body or chassis of the car
1
!"#$%&'
To a live terminal in the fuse block connecting to the car battery (bypassing the ignition switch)
!"#$%& '()*+,-'./0'1230456789:;
2
To an accessory terminal in the fuse block
!"#$%&'()*
3
To the door sensor
!"#
4
! /
/
Solder the core wires to connect them securely.
!"#$%&'()* +
‰∑¬
7
1
1
2
3
4
2
!"#$
7
1
1
2
3
4
!"#$%&'(%)*+,-./0
– 3 –
KS-IF200
*
* 2
2
*
Fuse block
(GND)
(ACC)
( DOOR SW )
How to disconnect the connector
*
* 4
4
*
Fuse block
* 4 Not included with this unit.
!"#$%
* 4
* 4
CAUTION / / /
• To prevent short-circuit, cover the terminals of the UNUSED leads
with insulating tape.
!"#$%&'()* UNUSED
•
•
7
Ignition switch
!
!"
* 2 Not included with this unit.
!"#$%
* 2
2
*
*
7
( BATTERY B+ )
!"#$
Push down
!"
*
!"#$%&'(
•