HITEC X1 Touch Instruction Manual
  1. Manuals
  2. Brands
  3. HITEC Manuals
  4. Battery Charger
  5. X1 Touch
  6. Instruction manual

HITEC X1 Touch Instruction Manual

Ac/dc input professional balance charger/discharger multi charger
Hide thumbs Also See for X1 Touch:
Table of Contents

Advertisement

Quick Links

Download this manual
INSTRUCTION MANUAL

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the X1 Touch and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for HITEC X1 Touch

Summary of Contents for HITEC X1 Touch

  • Page 1 INSTRUCTION MANUAL...

  • Page 2: Table Of Contents

    Volt Meter .........................23 Memory Presets - Data Store/Load .................24 Hitec RCD USA will not be held responsible for any damages or injuries that 1. Storing Presets ....................24 may occur by persons who fail to follow these warnings or who fail to prop- 2.

  • Page 3: Introduction

    SPECIFICATIONS AND CHARGER LAYOUT Specifi cations Congratulations on your choice of the Hitec X1 Touch digital, intelligent touch screen interface charger from Hitec RCD USA. The Hitec X1 Touch is a high-per- AC Input 100 - 240 Volts AC DC Input...

  • Page 4: Features

    Dual Power Input continuous charging or discharging. The X1 Touch has the ability to operate on a variety of power sources. The power Users can call out this data at any time without any special program setting. source can be a 12 volt automotive-type battery, an 11 ~ 18 volt DC power supply, or a 100 ~ 240 volt AC household current.

  • Page 5: Warnings And Safety Notes

    Hitec Charge Master Software • Never attempt to charge or discharge the following types of batteries: The free “Hitec Charge Master” software gives you unparalleled ability to operate the - A battery fitted with an integral charge circuit or a protection circuit charger through the computer.
  • Page 6 Keep in mind that the gauge or thickness of your charging leads from the components X1 Touch to your battery must be of an acceptable current rating to handle the ap- - Batteries that are not expressly stated by the manufacturer to be suitable for plied charge current.

  • Page 7: Power Supply Connections

    POWER SUPPLY CONNECTIONS PROGRAMING INTERFACE The X1 Touch can be powered either from a wall outlet supplying 100- MAIN MENU 240VAC (50-60Hz) using the included AC power cord, or from a 12VDC When you power up the charger, you will see the following screen. This is automotive battery or an 11 ~ 18 volt DC, 30 amp power supply.

  • Page 8: User Interface

    SAFETY next system setting and press “NEXT” to enter the selected program menu. 1-720 Minutes the X1 Touch is unable to detect the proper charge cut off condi- TIME tions. This can happen when charging faulty cells, exhausted packs, or packs exhibiting abnormal resistance or voltage fluctuations.

  • Page 9: Charger Parameters

    SENSE charger’s sensitivity to the voltage drop that occurs when the pack nears full capacity. This is the voltage level at which the X1 Touch will stop charging the bat- LiPo 4.18 - 4.3V/Cell END VOLT tery. This feature allows LiPo and LiFe packs to be CHARGE LiIon 4.08 - 4.2 V/Cell...

  • Page 10: Charging Program

    CHARGER OPERATIONS (cont.) CHARGER OPERATIONS (cont.) Number of Cells 2. CHARGING PROGRAM The available program modes are dependent on the battery type used. The Touch the CELLS icon to enter the cell selection screen. Use the ◄- and +► chart below lists the different operations available for each type of battery. to select the exact number of cells that are in your pack.

  • Page 11: Program Start

    CHARGER OPERATIONS (cont.) CHARGER OPERATIONS (cont.) 3. PROGRAM START 4. PROGRAM STOP Touch the start button or touch and hold the framed Operation Program To stop the charge or discharge process, touch STOP. The process will stop for 3 seconds to start the program. The charger will check the number of and you will be taken back to the Main Menu battery cells automatically.

  • Page 12: Information Displayed During Operation

    CHARGER OPERATIONS (cont.) INFORMATION DISPLAYED DURING OPERATION USING THE CHARGE MASTER CHARGE CONTROL SOFTWARE Visit the Hitec RCD USA (www.hitecrcd.com) website to download the free 1. CHARGING STATUS MONITOR 2. GRAPH CHARGE MASTER software for Windows PC’s. With the Charge Master soft-...

  • Page 13: Memory Presets - Data Store/Load

    CHARGER OPERATIONS (cont.) CONFORMITY DECLARATION MEMORY PRESETS – DATA STORE/LOAD The Hitec X1 Touch satisfies all relevant and mandatory EC directives and FCC Part The X1 Touch charger can store up to 5 different charge/discharge profiles 15 Subpart B:2008. for your convenience. These stored profiles can be recalled quickly without This product has been tested to meet the following technical standards: having to go through the setup process.

  • Page 14: Warranty And Service

    ONE YEAR LIMITED WARRANTY For a period of one year from the date of purchase, HITEC RCD USA, INC. shall REPAIR OR REPLACE, at our option, defective equipment covered by this warranty. Other- wise, the purchaser and/or consumer is responsible for any charges for the repair or replacement of the charger.
  • Page 15 www.hitecrcd.com...

Table of Contents